Guangzhou Biaiyue Electronic Products BER-TRV2S Digital Proportional Radio Control FHSS System Instruction Manual
- June 13, 2024
- Guangzhou Biaiyue Electronic Products
Table of Contents
- Thank you!
- radio control products
- SAFETY GUIDE
- QUICK OPERATOR GUIDE
- FCC Caution
- AUX CHANNEL ( 3CH )
- STEERING DUAL RATES ADJUSTMENT (ST.DIR)
- FAIL SAFE SETUP (S/F)
- TH.TRIM AND ST.TRIM ADJUSTMENT
- HANDING FOR BATTERY
- RECEIVER(RX) CONNECTION DIAGRAM
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Guangzhou Biaiyue Electronic Products BER-TRV2S Digital Proportional Radio Control FHSS System
Thank you!
Thank you for purchasing BER radio control products.
Beforing using,please patience reading this manual carefully.
radio control products
SAFETY GUIDE
To work with your models correctly and safely.This product is only equipped for radio controlled models.
- The usage of this product should be approved by local law and relevant regulations.
- We will not be responsible for the damage caused by unauthorized modification, adjustment and replacement of parts of this product.
- First turn on the transmitter make sure the batteries are well loaded. The voltage of TR batteries is never low than 4.4V.Then please check and confirm that the servos are all well and proper connected. Finally the receiver connect the full power.
- Keeping the radio away from moist,high temperature,and strong interference place. Please do not clean the radio with solvent. Do not strong shake.
- The antenna (silver part) does not touch anything or be bent when radio working. Otherwise will inference the control range or lead the radio out of control.
- Please do not play in night, bad weather such as rainy day or thundering days. Do not play beside high-voltage wire. Do not play near high power radio transmitting station etc. It will strong interfere the transmitter signal and lead unexpected accident.
- Before playing, please making sure the movement of servo correspond with you used to.
- Before starting, please making sure the TH and TH. TRIM in the lowest position or TH. TRIM in the neutral position.
- The sequence to end playing, Turning off the receiver first, then tum off the transmitter(TR) power and take out batteries. If operation is opposite, leading uncontrolled and accident.
- If the operators do not comply with safety guides instruction. may lead to serious injuries to yourself or others.
- The manual may be altered without prior notice to. Please contact us if you have any corrections or clarification that should be made in this instruction.
QUICK OPERATOR GUIDE
BINDING PROCESS:
Transmitter (TR) with batteries and keep 3CH button switch on, the TR led blue
light flashing and buzzer sound ‘B-B-B … ‘. It is in matching status. Then
receiver(RX)connect power, the RX led green light slow flash, Putting RX close
TR and keep RX BIND button till led green light quick flash several times then
slow flash, It shows binding successful. And tum off TR power and switch on TR
again, RX led light green become solid, It’s working status.
SERVO DIRECTION: Keeping the “TH. R/N” or “ST. R/N” button arrow mark 2 seconds and meanwhile buzzer sound “B”. It has reversed the direction of TH or ST servo.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference
that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. The
device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction
AUX CHANNEL ( 3CH )
Press 3CH button one time the 3ch servo moving 90 <: Pressing again, return
back.
NOTE: When hold “3CH” swith on radio,It’s in binding process. 3CH is a
BIND button. Not 3CH at this time
STEERING DUAL RATES ADJUSTMENT (ST.DIR)
Adjusting the dual rate of steering by adjusting ST.DIR knob, the picture showing
FAIL SAFE SETUP (S/F)
This function is to protect your models when signal weak or lost.
F /S will automatic put TH in lowest position or in setted place.
- The F /S is setted in receiver and setting data will be saved.
- To electronic power models, the F/S has been setted in RX.
- To gas power model, Putting trigger in brake position, keeping F /S button till led green light quick flash several times then go solid, releasing F /S button, this F /S function setted successfully.
- Rebinding the receiver, need resetting the F/S function.
Caution : For your safety, when has setted F/S function.
Before playing, checking F /S function work is very necessary!
TH.TRIM AND ST.TRIM ADJUSTMENT
“TH.TRIM” and “ST.TRIM” Each have two push buttons Pressing, buzzer sound type: “BBB>>>>>B<<<<<BBB” Big sound Bin neutral position.
Caution: TR rebinding RX can not change the” TH” or “ST” trim position that you previously have been setted. Switching on TR frist make sure” TH. TRIM” in lowest position.
HANDING FOR BATTERY
- Making sure install the batteries are in correct polarity order. If batteries are loaded reversed, the TR may be damaged.
- Using AA 4 dry batters or Ni-MH4 batteries.
- We test use 2S Li-Po(7.4V) battery work but not guarantee, nor responsible for any damaged or injured if you insist on DIY do Caution: Before installing batteries, checking the correct polarity loaded and right connection is very necessary.
RECEIVER(RX) CONNECTION DIAGRAM
TR TYPE BER-TRV1S/TRV2S RX TYPE: BER-RXVlC
Channel: 3CH
Frequency: 2.4GHz
Use DC:6V l00mA
N.W.: 320
R/F Power: <= 20dBm ;
Modulation: 2-FSK ;
Channel: 3CH
Frequency: 2.4GHz
DC: 6V 20mA
N.W.: 6g
Sensitivity: 1024
Frequency Signal: FHSS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>