PITSOS RG57A2 Universal Air Conditioner Remote Control User Manual

RG57A2 Universal Air Conditioner Remote Control
User Manual

RG57A2 Universal Air Conditioner Remote Control

P1ZAI0982W – P1ZAO0982W
P1ZAI1282W – P1ZAO1282W
P1ZAI1884W – P1ZAO1884W
P1ZAI2484W – P1ZAO2484W

NOTE:

• Button’s design is based on a typical model and might be slightly different from the actual one you purchased, the actual shape shall prevail.
• All the functions described are accomplished by the unit. If the unit has no this feature, there is no corresponding operation that happened when pressing the relative button on the remote controller.
• When there are wide differences between “Remote controller Illustration” and “USER’S MANUAL” on the function description, the description of “USER’S MANUAL” shall prevail.

Remote Controller Specifications

Operation of buttons

1. ON/OFF Button
   This button turns the air conditioner ON and OFF.

2. MODE Button
   Press this button to modify the air conditioner mode in a sequence of the following: NOTE: Please do not select HEAT mode if the machine you purchased is cooling only type. Heat mode is not supported by the cooling-only appliance.

3. FAN Button
   Used to select the fan speed in four steps: NOTE: You can not switch the fan speed in AUTO or DRY mode.

4. SLEEP Button
   • Active/Disable sleep function. It can maintain the most comfortable temperature and save energy. This function is available on COOL, HEAT, or AUTO mode only.
   • For detail, see “sleep operation” in “USER S MANUAL”.
   NOTE: While the unit is running under SLEEP mode, it would be canceled if MODE, FAN SPEED, or ON/OFF button is pressed.

5. FRESH Button (applicable to RG57A3/BGEF and RG57D/BGE only)
   Active/Disable FRESH function. When the FRESH function is initiated, the Ionizer/ Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air.

6. TURBO Button
   Active/Disable Turbo function. Turbo function enables the unit to reach the preset temperature at cooling or heating operation in the shortest time(if the indoor unit does not support this function, there is no corresponding operation that happened when pressing this button.)

7. SELF CLEAN
   Button(applicable to Rg57(A2)A3/BGEF) Active/Disable Self Clean function
   

8. UP Button( )
   Push this button to increase the indoor temperature setting in 1 C increments to 30º C.
   DOWN Button( )
   Push this button to decrease the indoor temperature setting in 1º C increments to 17º C.
   NOTE: Temperature control is not available in Fan mode.

9. SHORTCUT Button
   • Used to restore the current settings or resume previous settings.
   • On the first time connecting to the power, if push the SHORTCUT button, the unit will operate on AUTO mode, 26º C, and fan speed is Auto.
   • Push this button when the remote controller is on, the system will automatically revert back to the previous settings including operating mode, setting temperature, fan speed level, and sleep feature(if activated).
   • If pushing more than 2 seconds, the system will automatically restore the current operation settings including operating mode, setting temperature, fan speed level, and sleep feature(if activated ).

10. TIMER ON Button
    Press this button to initiate the auto-on-time sequence. Each press will increase the auto-timed setting in 30 minutes increments. When the setting time displays 10.0, each press will increase the auto-timed setting 60 minutes increments.
    To cancel the auto-timed program, simply adjust the auto-on time to 0.0.

11. TIMER OFF Button
    Press this button to initiate the auto-off time sequence. Each press will increase the auto-timed setting in 30 minutes increments.
    When the setting time displays 10.0, each press will increase the auto-timed setting 60 minutes increments. To cancel the auto-timed program, simply adjust the auto-off time to 0.0
    

12. Swing Button (applicable to RG57(A2)A3/BGEF)
    Used to stop or start vertical louver movement and set the desired left/right airflow direction. The vertical louver changes 6 degrees in angle for each press. And the temperature display area of the indoor unit displays for one second. I keep pushing for more than 2 seconds, the vertical louver swing feature is activated. And the display area of the indoor unit displays ‘ IIII ‘ flashes four times, then the temperature setting reverts back. If the vertical louver swing feature is stopped, it displays ‘LC’and remains on for 3 seconds.
    Swing Button (applicable to RG57A3(A2)/BGEF)
    Used to stop or start horizontal louver movement or set the desired up/down airflow direction.
    The louver changes 6 degrees in angle for each press. If I keep pushing for more than 2 seconds, the louver will swing up and down automatically.
    SWING Button (applicable to RG57B(D)/BGE)
    Used to stop or start horizontal louver auto swing feature.
    DIRECT Button(applicable to RG57B(D)/BGE)
    Used to change the louver movement and set the desired up/down airflow direction.
    The louver changes 6º in angle for each press.

13. FOLLOW ME Button
    (applicable to RG57(A2)A3/BGEF)
    Push this button to initiate the Follow Me feature, the remote display is actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow Me button again. The air conditioner will cancel the Follow Me feature automatically if it does not receive the signal during any 7 minutes interval.

14. LED Button
    Disable/Active indoor screen Display. When pushing the button, the indoor screen display is cleared, press it again to light the display.

Indicators on LCD

Information is displayed when the remote controller is powered up.

Mode display

| AUTO
---|---
| HEAT
| FAN
| COOL
| DRY
| Displayed when data is transmitted.
---|---
| Displayed when the remote controller is ON.
| Battery display(low battery detection)
| Not available for this unit
ON| Displayed when TIMER ON time is set.
OFF| Displayed when TIMER OFF time is set.
| Show set temperature or room temperature, or time under TIMER setting.
| Displayed in Sleep Mode operation.
| Indicated that the air conditioner is operating in Follow me mode
| Not available for this unit
| Not available for this unit

Fan speed indication

| Low speed
---|---
Medium speed
High speed
Auto fan speed

Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation, only the relative functional signs are shown on the display window.

How to use the buttons

| Auto operation
Ensure the unit is plugged in and power is available. The OPERATION indicator on the
the display panel of the indoor unit starts flashing.
1. Press the MODE button to select Auto.
2. Press the UP/DOWN button to set the desired temperature. The temperature can be set within a range of 17º C~ 30º C in 1º C increments.
3. Press the ON/off button to start the air conditioner.
NOTE
1. In the Auto mode, the air conditioner can logically choose the mode of Cooling, Fan, and Heating by sensing the difference between the actual ambient room temperature and the setting
the temperature on the remote controller.
2. In Auto mode, you can not switch the fan speed. It has already been automatically controlled.
3. If the Auto mode is not comfortable for you, the desired mode can be selected manually.
---|---
Cooling /Heating/Fan operation
Ensure the unit is plugged in and power is available.
1. Press the MODE button to select COOL, HEAT(cooling & heating models only), or FAN mode.
2. Press the UP/DOWN buttons to set the desired temperature. The temperature can be set within a range of 17º C~ 30º C in 1º C increments.
3. Press the FAN button to select the fan speed in four steps- Auto, Low, Med, or High.
4. Press the ON/OFF button to start the air conditioner.
NOTE
In the FAN mode, the setting temperature is not displayed in the remote controller and you are not
able to control the room temperature either. In this case, only steps 1, 3, and 4 may be performed.

Dehumidifying operation
Ensure the unit is plugged in and power is available. The OPERATION indicator on the display panel of the indoor unit starts flashing.

1. Press the MODE button to select DRY mode.
2. Press the UP/DOWN buttons to set the desired temperature. The temperature can be set within a range of 17º C~ 30º C in 1º C increments.
3. Press the ON/OFF button to start the air conditioner.

NOTE
In the Dehumidifying mode, you can not switch the fan speed. It has already been automatically controlled.
Adjusting airflow direction
Use the SWING & button to adjust the desired airflow direction.

1. The up/Down direction can be adjusted with the button on the remote controller. Each time when you press the button, the louver moves an angle of 6 degrees. If pressing for more than 2 seconds ,the louver will swing up and down automatically.
2. The left/Right direction can be adjusted with the button on the remote controller. Each time when you press the button, the louver moves an angle of 6 degree. If pressing for more than 2 seconds ,the louver will swing up and down automatically.

NOTE: When the louver swing or move to a position which would affect the cooling or heating effect of the air conditioner, it would automatically change the swing/moving direction.

Timer operation
Pressing the TIMER ON button can set the auto-on time of the unit. Pressing the TIMER OFF button can set the auto-off time of the unit.
To set the Auto-on time.

1. Press the TIMER ON button. The remote controller shows TIMER ON, the last Auto-on setting time and the signal “H” will be shown on the LCD display area. Now it is ready to reset the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired auto-on time. Each time you press the button, the time increases by half an hour between 0 and 10 hours and by one hour between 10 and 24 hours.
3. After setting the TIMER ON, there will be a one-second delay before the remote controller transmits the signal to the air conditioner. Then, after approximately another 2 seconds, the signal “h” will disappear and the set temperature will re-appear on the LCD display window.

To set the Auto-off time.

1. Press the TIMER OFF button. The remote controller shows TIMER OFF, the last Auto-off setting time and the signal “H” will be shown on the LCD display area. Now it is ready to reset the Auto-off time to stop the operation.
2. Push the TIMER OFF button again to set desired Auto-off time. Each time you press the button, the time increases by half an hour between 0 and 10 hours and by one hour between 10 and 24 hours.
3. After setting the TIMER OFF, there will be a one-second delay before the remote controller transmits the signal to the air conditioner. Then, after approximately another 2 seconds, the signal “H ” will disappear and the set temperature will re-appear on the LCD display window.

CAUTION

• When you select the timer operation, the remote controller automatically transmits the timer signal to the indoor unit for the specified time. Therefore, keep the remote controller in a location where it can transmit the signal to the indoor unit properly.
• The effective operation time set by the remote controller for the timer function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20, 21, 22, 23 ,and 24.

Example of timer setting

TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want the unit to turn on automatically before you return home. The air conditioner will automatically start operating at the set time.
Example:
To start the air conditioner in 6 hours.

1. Press the TIMER ON button, and the last setting of starting operation time and the signal “H” will show on the display area.
2. Press the TIMER ON button to display “6.0H ” on the TIMER ON display of the remote controller.
3. Wait for 3 seconds and the digital display area will show the temperature again. The “TIMER ON” indicator remains on and this function is activated.

TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when you want the unit to turn off automatically after you go to bed. The air conditioner will stop automatically at the set time.
Example:
To stop the air conditioner in 10 hours.

1. Press the TIMER OFF button, the last setting of stopping operation time and the signal “H” will show on the display area.
2. Press the TIMER OFF button to display “10H ” on the TIMER OFF display of the remote controller.
3. Wait for 3 seconds and the digital display area will show the temperature again. The “TIMER OFF” indicator remains on and this function is activated.

COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF → TIMER ON
(On → Stop → Start operation)
This feature is useful when you want to stop the air conditioner after you go to bed and start it again in the morning when you wake up or when you return home.
Example:
Stop the air conditioner 2 hours after setting and start it again 10 hours after setting.

1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0H on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10H on the TIMER ON display.
5. Wait for 3 seconds and the digital display area will show the temperature again. The “TIMER ON OFF” indicator remains on and this function is activated.

TIMER ON → TIMER OFF
(Off → Start → Stop operation)
This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house.
Example:
Start the air conditioner 2 hours after setting, and stop it 5 hours after setting.

1. Press the TIMER ON button.
2. Press the TIMER ON button again to display 2.0H on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display 5.0H on the TIMER OFF display.
5. Wait for 3 seconds and the digital display area will show the temperature again. The “TIMER ON & TIMER OFF” indicator remains on and this function is activated.

Handling the remote controller

Location of the remote controller.

• Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is confirmed by a beep.

CAUTIONS

• The air conditioner will not operate if curtains, doors, or other materials block the signals from the remote controller to the indoor unit.
• Prevent any liquid from falling into the remote controller. Do not expose the remote controller to direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly. Use curtains to prevent the sunlight from falling on the receiver.
• If other electrical appliances react to the remote controller, either move these appliances or consult your local dealer.
• Do not drop the remote controller. Handle with care.
• Do not place heavy objects on the remote controller, or step on it.

Using the remote controller holder(optional)

• The remote controller can be attached to a wall or pillar by using a remote controller holder(not supplied, purchased separately).
• Before installing the remote controller, check that the air conditioner receives the signals properly.
• Install the remote controller with two screws.
• For installing or removing the remote controller, move it up or down in the holder.

Replacing batteries
The following cases signify exhausted batteries. Replace old batteries with new ones.

• Receiving beep is not emitted when a signal is transmitted.
• The indicator fades away.

The remote controller is powered by two dry batteries (R03/LR03X2) housed in the back rear part and protected by a cover.

1. Remove the cover in the rear part of the remote controller.
2. Remove the old batteries and insert the new batteries, placing the(+) and (-) ends correctly.
3. Install the cover back on.

NOTE: When the batteries are removed, the remote controller erases all programming. After inserting new batteries, the remote controller must be reprogrammed.
CAUTIONS

• Do not mix old and new batteries or batteries of different types.
• Do not leave the batteries in the remote controller if they are not going to be used for 2 or 3 months.
• Do not dispose of batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>