LIGHTWARE HDMI 4K Manager User Guide
- June 15, 2024
- LIGHTWARE
Table of Contents
- Important safety instructions
- Introduction
- Box Contents
- Front and rear view
- Front panel LEDs
- Installation
- EDID emulation
- EDID learning (OUTPUT LED)
- Further EDID options
- EDID memory structure
- Powering Options
- HDCP management
- Restoring the factory default settings
- Typical application diagram
- Specifications
- Software control – Using Lightware Device Controller (LDC)
- EDID management
- Firmware update – Using Lightware Device Updater (LDU)
- Audio Cable Wiring Guide
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
**LIGHTWARE HDMI 4K Manager User Guide
**
Important safety instructions
Please read the supplied safety instruction document before using the product and keep it available for future reference.
Introduction
HDMI-4K Manager is a multifunctional interface with built‑in EDID Management
and Pixel Accurate Reclocking, supporting DVI and HDMI 1.4 signals with or
without HDCP encryption.
The output signal is reclocked and stabilized using Lightware Pixel Accurate
Reclocking technology to remove jitter caused by long cables or poor quality
sources
Box Contents
-
HDMI-4K Manage
-
5V DC Power Adaptor with Interchangeable Plugs
-
USB Cable
-
Safety and Warranty info, Quick Start Guide
Front and rear view
Never use a third-party power supply but the supplied one or use Light ware’s rack mountable power supply unit with the appropriate DC-DC cable.
Legend
- HDMI in HDMI input port for sources and for supplying the device with power (depends on source capabilities). The applied cable shall not be more than 20 m (4Kp30) or 30 m (1080p60).
- EDID rotary switches The rotary switches select one of the EDID memory addresses.
- Status LEDs The LEDs display information about the signal states.
- Learn button Store the EDID of the sink on HDMI OUT or start the device on bootload mode.
- USB control USB mini-B type connector to access special settings perform a firmware upgrade and supply the unit with power
- DC in . Input for the supplied power adaptor.
- Hidden button Button for resetting the device.
- HDMI output Connect an HDMI cable between the sink and the unit.
Front panel LEDs
LIVE
- BLINKING: the device is powered properly and operational.
- ON: shows the malfunction of the CPU; please restart the device.
INPUT
- ON (orange): source is connected (5V detected).
- ON (green): signal is present.
AUDIO
- ON (red): HDMI, multichannel / compressed audio signal is detected.
- ON (purple): HDMI, PCM 2 channel audio signal is detected.
- OFF: no audio is transmitted.
OUTPUT
- ON (green): hotplug detected on HDMI OUT.
Installation
- Connect the desired source to the HDMI input port.
- Connect a sink device to the HDMI output port.
- Optionally connect a laptop or PC to the USB port and run LDC software.
- First connect the power cord of the supplied adaptor to the DC input, then to the AC power socket.
EDID emulation
Selecting an EDID
Turn the EDID address rotary switches to the desired position. Use a flat head screwdriver to change the address. The left switch sets the tens value, the right switch gives the ones value of the EDID.
Avoid the use of keys, coins, knives and other sharp objects
EDID learning (OUTPUT LED)
The EDID of the sink connected to HDMI OUT 1 can be stored in the user EDID memory:
- Turn the EDID rotary switches to the desired position (between #62 – #98).
- Press the LEARN button and keep it pressed for three seconds.
- The OUTPUT LED turns dark for a second, then provides feedback:
- BLINKING (green): EDID learning is successful, the EDID is stored.
- BLINKING (red): EDID learning is failed.
- The LED turns dark for a second, then shows the state(s) of the connected sink(s)
Further EDID options
The following functions are available when connecting to the device by LDC:
-
EDID learning or importing an EDID.
-
Exporting an EDID and saving it as a file.
-
Creating a custom EDID by using the EDID Editor or the Easy EDID Creator.
-
Deleting an EDID (from the user memory).
EDID memory structure
01-11: DVI EDIDs; 12-55: HDMI EDIDs
ID| Resolution| ID| Resolution| ID| Resolution|
ID| Resolution
---|---|---|---|---|---|---|---
00| Copy HDMI1| 14| 640x480p59| 28| 1920x1080i50_2| 42| 3440x1440p24
01| 640x480p60| 15| 720x480p59| 29| 1920x1080i60| 43| 3440x1440p30
02| 800x600p60| 16| 720x576p50| 30| 1920x1080i60| 44| 2560x1600p60
03| 1024x768p60| 17| 1280x720p50| 31| 1920x1080p24| 45| 2560x2048p50
04| 1280x768p50| 18| 1280x720p60| 32| 1920x1080p30| 46| 3840x2160p24
05| 1280x768p60| 19| 1024x768p60| 33| 1920x1080p50| 47| 3840x2160p30
06| 1280x1024p50| 20| 1366x768p60| 34| 1920x1080p60| 48| 3840x2160p60
07| 1280x1024p60| 21| 1280x800p60| 35| 1920x1080p60| 49| 4096x2160p24
08| 1600x1200p50| 22| 1440x900p60| 36| 2048x1080p60| 50| 4096x2160p30
09| 1600x1200p60| 23| 1600x900p60| 37| 2560x1080p60| 51| 4096x2160p60
10| 1920x1200p50| 24| 1280x1024p50| 38| 1600x1200p50| 52| 3840x2400p24
11| 1920x1200p60| 25| 1280x1024p60| 39| 1600x1200p60| 53| 3840x2400p30
12| 1440x480i60| 26| 1440x1080p60| 40| 1920x1200p60| 54| 720p60_3D
13| 1440x576i50| 27| 1920x1080i50_1| 41| 2560x1440p60| 55| 1080p60_3D
ID| Description| ID| Description
---|---|---|---
56| Universal DVI| 60| Universal HDMI 4K PCM AUDIO
57| Universal HDMI PCM AUDIO| 61| Universal HDMI 4K ALL AUDIO
58| Universal HDMI ALL AUDIO| 62-98| User EDIDs
59| Universal HDMI DC ALL AUDIO| 99| Copy HDMI2
Powering Options
The device can be powered by any of the following ways:
- Using the supplied power adaptor (recommended).
- Connect the device to a proper USB port by the supplied cable.
- Connecting an HDMI source to the HDMI input port.
Make sure that the port is able to supply 5V 500 mA current
If the power adaptor is connected, it will supply the device independently from the HDMI/ USB ports. If the adaptor is disconnected from the DC input connector, the device tries to use a different power source (HDMI or USB) if it is enabled and connected. (If the adaptor is unplugged from the AC socket but the DC plug is still connected, the device will be switched off and cannot be changed to another power source. Unplug the DC cable from the device to be powered by USB or HDMI.)
The USB and HDMI powering modes can be enabled/disabled via the LDC software.
- If you are not sure that your USB or HDMI port has enough power, disable the powering over USB and HDMI by Lightware Device Controller software. If the supplied power over USB or HDMI is not enough, the device will switch off. In the case of any strange behavior of the device, please disconnect the USB and HDMI cables and connect the 5V DC adaptor.
HDCP management
The HDCP setting of the HDMI input port can be enabled/disabled on the front panel as follows:
- Turn the EDID rotary switches to ‘01’ position.
- Press the LEARN button and keep it pressed for three seconds.
- The lower three LEDs give displays if the HDCP state is changed:
- Output→Audio→Input LEDs are dark and light up sequentially: HDCP is enabled.
- Input→Audio→Output LEDs light and get dark sequentially: HDCP is disabled.
Restoring the factory default settings
The settings and parameters can be set to factory default as follows:
- Set the rotary switches to ‘00’ position.
- Press and keep pressing the LEARN button for three seconds. When the lower three LEDs blink, release the button. The following settings and parameters are restored:
HDCP (input port): enabled
HDCP (output port): auto
HDMI mode (output port) : auto
HDMI output port (audio signal): unmuted
Test pattern generator: off
Typical application diagram
Specifications
General
Compliance : CE, UKCA
EMI (Emission): EN 55032:2015+A1:2020
EMI ( Immunity ): EN 55035:2017+A11:2020
Safety: EN 62368-1:2020
RoHS: EN 63000:2018
Cooling: passive
Power
Power supply : external power adaptor / HDMI input port / USB port
Power adaptor : Input 100-240 V AC 50/60 Hz, Output 5V DC, 3 A
Power consumption: 1.8 W (max)
Digital video signal
HDMI connector: 19-pole HDMI Type A receptacle
Supported si g nals: DVI 1.0, HDMI 1.4
Signal standard: DVI and HDMI standard which supports embedded audio
Supported resolutions : up to 4K / UHD (30Hz RGB 4:4:4, 60Hz YCbCr
4:2:0)
3D support: yes
HDCP compliant: yes
Control over CEC: yes, transparent
Re clocking: Pixel Accurate Reclocking
Cable length (input port) : max 20 m (4Kp30) or 30 m (1080p60)
EDID management
EDID emulation: yes
EDID memory : 61 factory presets, 37 user-programmable
Control
USB port : USB mini-B receptacle
Software control – Using Lightware Device Controller (LDC)
The device can be controlled from a computer using the Lightware Device Controller software. The application is available at www.lightware.com (Support / Downloads section), install it on a Windows PC or a MacOS and connect to the device.
Connecting by the USB port
Connect the supplied USB cable between the device and the computer and start the LDC.
The device is displayed under the USB devices section; select it, then press Connect.
Crosspoint menu
When LDC connects to the device, the Crosspoint menu is shown by default. The input and output port settings are available separately for the video and audio signals. Besides, the following tools are available:
Frame detector
The ports can show detailed information about the signal like blanking intervals and active video resolution. This feature is a good troubleshooter if compatibility problems occur during system installation.
Test pattern generator
The output ports can send a special image towards the sink devices for testing purposes. The settings of the test pattern are available via LDC:
Mode
- On: the test pattern is always sent to the output port.
- Off: the test pattern generator is off.
- No signal: the test pattern generator is switched on if video signal is not detected.
Clock source
- 480p / 576p / Original video signal: the clock frequency of the test pattern.
Pattern
- Red / Green / Blue / Black / White / Ramp / Chess / Bar / Cycle. Cycle setting means all the patterns are changed sequentially approx. in every 2 seconds.
EDID management
Advanced EDID Management can be accessed by selecting the EDID menu. The software allows to create, modify, delete, import, or export EDIDs. Please note that the factory presets cannot be modified.
EDID emulation is available only by the EDID rotary switches on the device
**Backup and restore (Configuration cloning)
**
This simple method eliminates the need to repeatedly configure certain devices to have identical (non-factory) settings. If the devices are installed in the same type of system multiple times, then it is enough to set up only one device to fit the user’s needs and then copy those settings to the others, thus saving time and resources. Installing multiple devices with the same customized configuration settings can be done in a few easy steps:
- Configure one device with all your desired settings with the LDC software.
- Backup the full configuration file to your computer.
- If needed, make some modifications to the configuration file using a text editor.
- Connect to the other device that has to be configured and upload (restore) your configuration file.
Firmware update – Using Lightware Device Updater (LDU)
Preparation
The following are necessary to perform a firmware update:
- Lightware Device Updater software – available on www.lightware.com,
- Firmware package of the device (LFP file) – please contact support@lightware.com.
- Power adaptor to supply the device
Performing the Update
- The device must be supplied with the power adapter when the firmware is updated.
Supplying the device over USB or HDMI is not recommended for this process.
- Connect a PC/laptop to the USB port of the device by the supplied USB cable.
- Start the LDU software and follow the instructions shown on the screen.
Starting the unit in bootload mode
If the usual firmware update cannot be performed for any reason, try the following:
- Press the LEARN button and keep it pressed.
- Press and release the hidden button.
- Release the LEARN button. The device is restarted in boot load mode.
Audio Cable Wiring Guide
The device is built with a 5-pole Phoenix connector, so we would like to help users assemble their own audio cables. See the most common cases below.
Balanced output to balanced input Phoenix – 2×6.3 (1/4”) TRS
Balanced output to balanced input Phoenix cable – 2x XLR plugs
Balanced output to unbalanced input Phoenix – 2x RCA
Balanced output to unbalanced input Phoenix – 2x 6.3 (1/4”) TS
For more information about the audio cable wiring, see the Audio Cable Wiring Guide on our website www.lightware.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>