SOLIGHT WM-20W-RE LED Spotlight Instruction Manual

: August 16, 2024
: Solight

Table of Contents

SOLIGHT WM-20W-RE LED Spotlight
TECHNICAL PARAMETERS
DESCRIPTION OF EQUIPMEN
POSITIONING OF THE REFLECTOR
Operating the Device
Charging
Maintenance and storage
FAQ
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SOLIGHT WM-20W-RE LED Spotlight

Specifications

Luminous flux: 2000lm*
Power: 20W
Chromaticity temperature: 4000K
Light source: 40x SMD2835 LEDs
Batteries: Li-Ion (4400mAh, 3.7V)
Battery life: min. 2h/max. 10h
Battery charging time: approx. 4h
LED lifetime: 20,000 hours
Coverage: IP54

Thank you for purchasing our portable LED spotlight. Please read this manual carefully and heed the safety warnings and instructions before installing, using or repairing the unit. Doing so will ensure not only the protection of persons, but also the longevity of the equipment.

TECHNICAL PARAMETERS

DESCRIPTION OF EQUIPMEN

Spotlight
Handle
LED panel
Stand
USB-C charging cable
Wing nut for fixing the tilt
Charging indicator
Battery status button
USB-C socket cover
ON/OFF button
USB-C charging socket

Safety Notice
Positioning of the Reflector: You can adjust the position of the device vertically and horizontally.

Fully charge the batteries before starting the device for the first time.
The device is not intended for children.
If the device is damaged, do not use it further.
Neither the manufacturer nor the distributor shall be liable for any damage caused by improper use of the product.
Do not repair or modify the equipment, all repairs must only be carried out by the manufacturer’s service centre.
Do not open the cover or otherwise interfere with the construction of the product.
Keep the device away from: open flames, hot surfaces and flammable materials.
Place the device at least 0.1m from the object to be illuminated.
Do not cover/uncover the product while charging, as this creates a risk of overheating.
Keep the batteries out of the reach of children.
The battery is not replaceable, in the case of failure the entire device must be disposed of in a designated place.

POSITIONING OF THE REFLECTOR

You can adjust the position of the device vertically and horizontally.

Using the handle (2), place the product on a flat and stable surface.
Loosen the rotation screws (6) to adjust the LED panel (3) to the desired position.

Tighten the pivot screws when the adjustment is complete.

Operating the Device

The device can be operated in different modes. These can be selected by repeatedly pressing the ON/OFF button.

Press : 100% illumination
Press : 50% illumination
Press : 20% illumination
Off

Charging

Open the cover (9) of the USB-C charging socket and connect the supplied charging cable to the socket (11). Connect the charging cable to a 5V, max. 2A AC adapter (not included) and plug it into a power outlet. (It is not possible to switch on the reflector while it is charging. Always charge in a dry place.) When charging, all the indicator lights (7) start flashing. The battery is fully charged when all lights are on continuously.

NOTE:
After charging is complete, be sure to reattach the USB input cover (9) to protect the reflector from moisture and to ensure protection against splashing water.

Switching On/Off:
Press the ON/OFF button (10) to switch the device on/off.

Maintenance and storage

Do not use chemicals for cleaning. Use a dry, lint-free cloth. Clean only when the product is switched off and disconnected.
When not in use, store the device in a dry place inside its packaging.
To maintain the capacity of the rechargeable battery, the device needs to be charged for two hours every 4 months.

The light source of this luminaire is non-replaceable, at the end of its service life the entire luminaire must be replaced and disposed of in a designated place. This product contains a light source that for design reasons cannot be removed for verification and therefore the entire product is considered a light source

Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, Czech Republic