REDMAGIC NX729J 8 Pro Smartphone User Guide

: June 13, 2024
: REDMAGIC

NX729J

Quick Start Guide

Legal notice

Copyright Statement

All the copyrights of this document herein belong to Shenzhen Tengfei Technology Management Ltd. Without the written permission of copyright owner, no part of this publication may be excerpted, reproduced, translated by any person or entity in any form or by any means.

This document is subject to change without prior notice.

Shenzhen Tengfei Technology Management Ltd.

keeps the right to make the final explanation to this document.

Trademarks

Android is a trademark of Google, Inc.

Statement of Third-party Applications

During the installation process of some third-party applications, the issues of repeated restart or abnormal use of software might be caused by incompatibility of the third-party applications, rather than the phone itself.

Please download your software upgrade packages from the reliable official website.

The installation of a third-party ROM or non-official operating system might bring safety risks and security threats. Shenzhen Tengfei Technology Management Ltd.

shall not be liable for these risks and threats caused by upgrade of the operating system.

Your phone at a glance

Light/Proximity Sensor
Shoulder Trigger(L)
Power Button
Game MIC
Touch Screen
Shoulder Trigger(R)
USB Type-C Port
Card Tray
Fingerprint Sensor
Volume Buttons
Front Camera
Receive
Headphone
Flash
Rear Camera
Air Inlet
Microphone
Speaker
Game Boost Mode
Air Outlet
NFC
Noise-reduction MIC

Inserting the SIM card

Insert the end of the eject tool into the hole of the card tray and press firmly until the tray pops out.
Put one or two nano-SIM cards into the tray.
Push the card tray back into the phone.

REDMAGIC NX729J 8 Pro Smartphone A2

Note
Dimensions of a nano-SIM card: 9 mm*12 mm.

Charging the battery

Connect the phone to the power adapter using the included USB cable and power adapter.

REDMAGIC NX729J 8 Pro Smartphone A3

Note
Your phone and power adapter might heat up while charging.

Use other USB cable or power adapter might decrease the life span of your phone or cause fire, explosion and other hazards.

The illustrations of products and accessories in the user guide are all schematic diagrams and are for reference only.
Due to product updates and upgrades, the actual product and the schematic diagram may be slightly different, please refer to the actual product.

Powering On/Off Phone

Make sure the battery is charged before powering on.

Press and hold the Power key to turn on your phone.
To power off, press and hold the Power key and touch ,,Swipe to power off .

Waking Up Your Phone

Your phone automatically goes into sleep mode when it is not in use for some time. The display is turned off to save power and the keys are locked to prevent accidental operations.
You can wake up your phone by turning on the display and unlocking the keys.

Press the Power key to turn the screen on.
Swipe up on the screen.

Note
If you have set an unlock pattern, a PIN, or a password for your phone, youll need to draw the pattern, or enter the PIN/password to unlock the phone.

Hardware and software

The certified hardware version of your phone is

NX729J _V1AMB.

The certified software version of your phone is

NX729J_UNCommon_V3.03.

The Wi-Fi function for this device is restricted to indoor use only when operating in the 5150 MHz to 5350 MHz frequency range.

Safety warning

To prevent possible hearing damage when using a headset, do not use high volume for long period.
Use the earphone carefully. Excessive sound pressure from headsets and headphones can cause hearing loss.
Adapter shall be installed near the equipment and shall be easily accessible.
The phone’s normal operating temperature is 0°C ~ 40°C. In order to ensure the normal phone functions, do not use this phone outside the temperature range.

CAUTION

Risk of explosion if the battery is replaced by an incorrect type disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

FCC Regulatory Compliance

• FCC Regulations:

This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

Caution:
Changes or modifications not expressly approved by Shenzhen Tengfei Technology Management Ltd. for compliance could void the user,,s authority to operate the equipment.

• RF exposure information (SAR)

This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.

This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528.

The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID:2A9QD-NX729J.

The SAR limit set by the FCC is 1.6 W/Kg.

The highest reported SAR value for this device when using against the head is less than 1.6 W/Kg, for usage near the body-worn is less than 1.6 W/Kg(1g- 10mm).

Body worn operation

SAR compliance for body-worn operation is based on a separation distance of 10 mm between the unit and the human body. Carry this device at least 10 mm away from your body to ensure RF exposure level compliant or lower to the reported level. Ensure that the device accessories, such as a device case and device holster, are not composed of metal components. Keep the device away from your body to meet the distance requirement.

Hardware and software

The certified hardware version of your phone is

NX729J _V1AMB.

The certified software version of your phone is

NX729J_UNCommon_V3.03.

FCC Caution.

§ 15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

FCC Hearing-Aid Compatibility (HAC)

Your phone is compliant with the FCC Hearing Aid Compatibility requirements.

The FCC has adopted HAC rules for digital wireless phones. These rules require certain phones to be tested and rated under the American National Standard Institute (ANSI) C63.19-2011 hearing aid compatibility standards. The ANSI standard for hearing aid compatibility contains two types of ratings:

M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices than mobile devices that are not labelled. M4 is the better/higher of the two ratings.
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to work better with a hearing devices telecoil (“T Switch” or “Telephone Switch”) than unrated phones. T4 is the better/ higher of the two ratings. (Note not all hearing devices have telecoils in them.)

The tested M-Rating and T-Rating for this device ( FCC ID: 2A9QD-NX729J ) M4 and T3.

WARNING: Cancer and Reproductive Harm –www.P65Warnings.ca.gov.