TOPPING MQADX5 Lite DAC and Headphone Amplifier User Manual

DX5 MOAIDXS5 Lite
DAC & Headphone amplifier
User manual

MQADX5 Lite DAC and Headphone Amplifier

Thank you for purchasing TOPPING DX5 MOA/DX5 Lite! The DX5 MQA/DX5 Lite is a high-performance device with multi-channel digital inputs, two Line Out outputs and two headphone outputs. It can be used as not only a HIFI DAC & headphone amp, but also a simple DAC or DAC .0. pre-amplifier, we hope it could bring you more fun at enjoying music. Now we recommend you read this manual so that you can use all the features of DX5 MOAKIX5 Lite correctly.

Introduction to MQA

MQA (Master Quality Authenticated) is an award-winning British technology that delivers the sound of the original master recording. The master MQA file is fully authenticated and is small enough to stream or download. DX5 MQA adopts MOA technology to receive and decode MQA audio and provide master-level sound. Visit mqa.co.uk for more information. Note: Only DX5 MQA supports MQA decoding. DX5 Lite does not.

Contents list

Note: You can download the driver and user manual on http://www.topping.audio/.

Attribute

4-PIN-XLR headphone output jack
Display| White OLED
Standby power consumption| <1.5W
Power consumption in normal usage| <6.0W

Front panel

1-1 4-PIN-XLR headphone output jack
1-2 6.35mm headphone output jack
1-3 Remote control receiver
1-4 OLED screen
1-5 Volume knob/Muti-function Button
Rear panel

2-1 Right channel balanced XLR output
2-2 Left channel balanced XLR output
2-3 Left channel single-ended RCA output
2-4 Right channel single-ended RCA output
2-5 Bluetooth input
2-6 USB input
2-7 Coaxial SPDIF input
2-8 Optical SPDIF input
2-9 Power input (AC 100-240V 50Hz/60Hz)
2-10 Power switch
*Note: Description of XLR male connector pin definition.
1. GND 2.+ 3. –

Display

3-1 Input
3-2 Output
3-3 Current sampling rate
3-4 Volume
3-5 PCM/DSD/MQA format indication (MQA format indication for DX5 MQA only) *
*Note: There are three forms of MQA operation modes.

1. MQA”: Indicates that the product is decoding and playing an MQA stream or file, and denotes provenance to ensure that the sound is identical to that of the source material.
2. ‘MQA.”: Indicates it is playing an MQAStudio file, which has either been approved in the studio by the artist/producer or has been verified by the copyright owner.
3. OFS”: Confirms that the product is receiving an MQA stream or file.

This delivers the final unfold of the MQA file and displays the original s ample rate.

Remote control

4-1 Standby
4-2 Volume up
4-3 Switch to previous input
4-4 Headphone amp output
4-5 Filter setting
4-6 Automatic standby
4-7 Mute
4-8 Headphone amp & Line Out output
4-9 Switch to next input
4-10 Volume down
4-11 Line Out output
4-12 Quick menu (Refer to Setup Menu)
4-13 Brightness*

*Note:

1.  “DIS: A” has the same brightness as “DIS: M”. The differences lie in when there is no operation after 30 seconds under” DIS A” mode, the screen will be automatically turned off, only display a dot at the bottom right corner. You can press any button to light up the screen.
2. When DX5 MQA/DX5 Lite is in Bluetooth input state, keep pressing the brightness button for 3 seconds to disconnect the existing Bluetooth connection and forcibly enter into Bluetooth pairing state.

Input range

DSD DSD64-DSD512 (Native) , DSD64-DSD256 (Dop)
MQA Full Decode (Only supported in DX5 MQA)
COAX/OPT IN| PCM 44.1kHz-192kHz/16bit-24bit
DSD DSD64 (Dop)
MQA Full Decode (Only supported in DX5 MQA)
BT IN| AAC/SBC/APTX/APTX LL/APTX HD/LDAC

Specifications

DX5 MQA/DX5 Lite Decoding parameters (LineOut/USB In@96kHz)

| RCA| XLR
THD+N@1 kHz (A-wt)| <0.00010%| <0.00009%
THD @20-20kHz 90kBw| <0.0005%| <0.0002%
SNR©l kHz (A-we| 125dB| 128dB
Dynamic range @1 kHz (A-wt)| 125dB| 128dB
Frequency Response| 20Hz-20kHz (±0.1 dB)| 20Hz-20kHz (±0.1 dB)
20Hz-40kHz (±0.3dB)| 20Hz-40kHz (±0.3dB)
Output Level| 2.1Vrms @OdBFS| 4.2Vrms @OdBFS
Noise@A-wt| <1.5uVrms| <2.0uVrms
Channel Crosstalk| -130dB @1 kHz| -140dB @1 kHz
Channel Balance| 0.3 dB| 0.3 dB
Output Impedance| 500| 500
DX5 MQA/DX5 Lite Headphone Amplifier specifications (USB In@96kHz)

| 6.35mm headphone jack| 4-PIN-XLR headphone jack
THD+N
@1kHz (A-wt)| <0.00010% @Output=145mW (32())| <0.00010% @Output=145mW (32())
<0.00009% @Output=15mW (3000)| <0.00009% @Output=15mW (3000)
TH D
@20-20kHz 90kBW| <0.00050% @Output=145mW (320)| <0.00050% @Output=145mW (320)
<0.00020% @Output=15mW (3000)| <0.00030% @Output=15mW(3000)
SNR @MAX OUT 1kHz (A-wt)| 125dB@1kHz| 125dB @1kHz
Dynamic Range @1kHz (A-wt)| 125dB@1kHz| 125dB @1 kHz
Frequency
Response| 20Hz-20kHz (±0.1 dB)| 20Hz-20kHz (±0.1 dB)
20Hz-40kHz (±0.3dB)| 20Hz-40kHz (±0.3dB)
Output Level| 6Vpp @G=L| 6Vpp @G=L
25Vpp @G=H| 25Vpp @G=H
Noise @A-wt| <1.7uVrms @G=L| <1.7uVrms @G=L
<5.5uVrms @G=H| <5.5uVrms @G=H
Channel Crosstalk| -114dB @1kHz| -114dB @1kHz
---|---|---
Gain| G=L 6.7dB (Vrms/FS)| G=L 6.7dB (Vrms/FS)
G=H 19dB (Vrms/FS)| G=H 19dB (Vrms/FS)
Channel Balance| 0.3 dB| 0.3 dB
Output Impedance| <0.10| <0.10
Output Power| 1800mW x 2 @320 THD+N<1%| 1800mW x 2 @320 TH13+14<l%
woomw x 2 @640 THD+N<1%| 1000MW X 2 @640 THD+N<1%
250mW x 2 @3000 THD+N<1%| 250mW x 2 @3000 THD+N<1%
Load impedance| >80| >80

Operation

Power on & off / standby operation: (1) Power on & off: Press the power switch on the rear panel to turn DX5 MQA/DX5 Lite on or off. (2) Standby setting: When it is working, press and hold the multifunction button on the front panel to enter standby state and short press to exit standby state when it is in standby. Or you can directly press the standby button on remote control to enter or exit standby state.
Note: When the automatic standby function is on, if the current input is not connected or input signal is invalid in 1 minute, it will automatically enter the standby state. Once having detected valid signal, it will automatically return to working state. Volume setting: (1) The enter and exit of mute state: Press the mute button on the remotecontrol to set mute, press the mute button again or adjust the volumeto exit mute state. (2) Volume adjusting: You can directly turn the volume knob or press the volume up or down button on the remote control to adjust the volume.
Note that long pressing the volume up/down button on the remote control will quickly adjust the volume, so please be careful in order to protect your hearing. Input channel switching: Press the knob on the front panel or the “Switch to previous input button” and the “Switch to next input button” on the remote control to switch the input in cycle. Output channel switching: Double- click the knob on the front panel or use the Headphone amp output button, Headphone amp & Line Out output button, Line Out output button on the remote control to set the output channel. (Press the Line Out output button can select RCA or XLR or RCA+XLR output)
Setup Menu
Enter the setup menu: After switching the power switch to “power off”, press and hold the knob on the front panel while switching to “power on” to enter the setup menu of DX5 MQA/DX5 Lite. Change settings: (1) The knob on front panel: rotate the knob to enter the next setting item, press the knob to set different parameters. (2) The remote control: press the volume up/down button to enter the previous/next setting item, press the left/right button to set different parameters. When setting the 13th Channel balance, press the middle button to restore to balance.![TOPPING MQADX5 Lite DAC and Headphone Amplifier

• remote control1](https://manuals.plus/wp-content/uploads/2023/09/TOPPING- MQADX5-Lite-DAC-and-Headphone-Amplifier-remote-control1.jpg) Save Settings: Please choose the 14th option of “Save and exit”. Setting descriptions:

  1. Auto power on & off setting (available for remote control setting)
     Screen display| Description
     ---|---
     AUTO I ON| Auto power on (Default)
     AUTO I OFF| Auto power off
  2. creen brightness set ing (available for remote control setting)
     Screen display| Description
     ---|---
     Display I L| Low
     Display I M| Mid (Default)
     Display I H| High
     Display I A| Mid brightness and screen will be turned
     off automatically after no operation for 30s
  3. Line Out mode setting
     Screen display| Description
     ---|---
     LO Mode I PRE| Per-Amp mode (volume adjustable) (Default)
     LO Mode I DAC| DAC mode (volume nonadjustable)
  4. Headphone amp gain (Available for remote control setting)
     Screen display| Description
     ---|---
     GAIN I L| Headphone Amp-Low gain (Default)
     GAIN I H| Headphone Amp – High gain
  5. Output channel setting (Available for remote control setting)
     Screen display| Description
     ---|---
     OUTPUT I PO| Headphone amp output
     OUTPUT I LO| Line Out output
     OUTPUT I PO+LO| Headphone amp & Line Out output (Default)
  6. Line Out output setting (available for remote control setting)
     Screen display| Description
     ---|---
     LineOut I RCA+XLR| RCA&XLR Output simultaneously (Default)
     LineOut I RCA| RCA Output only
     LineOut I XLR| XLR Output only
  7. PCM filter setting (available for remote control setting. set PCM filter mode when playing PCM)
     Screen display| Description
     ---|---
     PCM FIR I Model| Fast roll off linear
     PCM FIR I Mode2| Slow roll off linear
     PCM FIR I Mode3| Fast roll off minimum (Default)
  8. Bluetooth setting
     Screen display| Description
     ---|---
     BT I ON| Bluetooth enabled (Default)
     BT I OFF| Bluetooth disabled
  9. Polarity setting
     Screen display| Description
     ---|---
     Phase Normal| Normal polarity (Default)
     Phase Invert| Inverted polarity
  10. Dithering setting (available for remote control setting)
      Screen display| Description
      ---|---
      Dithering low| Lowest noise (Default)
      Dithering mid| Lower distortion
      Dithering high| Lowest distortion
  11. Volume step below -50dB
      Screen display| Description
      ---|---
      Vol step 1.0dB| Volume step 1 dB (Default)
      Vol step 0.5dB| Volume step 0.5dB
  12. Sound mode setting (available for remote control setting)
      Screen display| Description
      ---|---
      Sound Mode OFF| Sound Mode OFF (Default)
      Valve Sound| Valve Sound
      Transistor Sound| Transistor Sound
  13. Channel balance setting (available for remote control setting)
      Screen display| Description
      ---|---
      Balance C| Balance (Default)
      Balance L +0.5d| Setting range: L+0.5-10dB
      Balance R +0.5d| Setting range: R+0.5-10dB
  14. Save settings and restart
      Factory reset| Reset default
      ---|---
  15. 15.Factory reset
      Screen display| Description
      ---|---
      Factory reset| Reset default

Quick menu: When it is working, press the M button of the remote control to enter the quick menu, the quick menu is extracted from the setting menu with 5 common settings, which includes

1. PCM filter setting (7th in setup menu)
2. Headphone amp gain (4th in setup menu)
3. Sound mode setting (12th in setup menu)
4. Channel balance setting (13th in setup menu)
5. Dithering setting (10th in setup menu) The way to change settings is as above, and press the M button to exit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>