HUDSON VALLEY 403-10-VB Oraibi 10 Light Chandelier Instruction Manual
- June 13, 2024
- HUDSON VALLEY
Table of Contents
HUDSON VALLEY 403-10-VB Oraibi 10 Light Chandelier Instruction Manual
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
FIXTURE INSTALLATION
- Attach the FIXTURE ASSEMBLY STEMS (L) to the FIXTURE ASSEMBLY (M).
- Feed the wire through the STEM (I) and twist tightly onto the WIRE BODY (K). Keep adding additional STEMS (1) until your desired hanging height is met.
- Slide the SLIP COLLAR (1), CANOPY (G) onto the STEM (1), and thread the CONNECTOR (H), with the NIPPLE (F), and NUT (C) onto the top end of the STEM (1). Screw on the CROSS BAR (A) to the NIPPLE (F), and tighten the NUT (C) to the bottom of the CROSSBAR (A)
- Pull the wires out from the junction box and install the CROSSBAR (A) onto the junction box using the MOUNTING SCREWS (E). This fixture is designed to be mounted on a standard round of octagon junction box. The junction box must be securely mounted to the structure of the building.
- Trim off excess wire to a minimum 6 beyond the STEM (J) and strip each wire 5/8″.
- Attach the Ground wire (Green) to the ground Inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (B) on the CROSSBAR (A). NEVER CONNECT GROUND WIRE TO “HOT WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I’ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
- Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Push the wires back into the junction box. Lift up the CANOPY (G) up to the ceiling, and secure with the SCREW COLLAR (1).
- Push the BULB (N) in to the socket of the fixture. THIS FIXTURE IS RATED FOR 4 WATT TYPE G9 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE! THIS FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT FLUORESCENT-INCANDESCENT LIGHT SOURCE.
- Screw on the GLASS (O) to the Shade of the FIXTURE ASSEMBLY (M)
- Restore power to the OUTLET at the breaker or fuse box.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>