CORBETT 452-10-VPB Fabriano LED Wall Sconce Instruction Manual

Table of Contents

CORBETT-452-10-VPB-Fabriano-LED-Wall-Sconce-product-
img

Product Name: Fabriano
Model Number: 5-
Manufacturer: Unknown
Replacement Parts: Hardware Kit (HDW-5), Alabaster Finial (ALA-5), and Finial (FIN-5)

Fixture Installation
- Mounting Plate (A) and secure it using Mounting Screws (B).
- Ground Screw (C) should be properly connected. Never connect the ground wire to the hot wire to avoid serious injury or death.
- Use Wire Nut (D) to secure the wires properly. Ensure there are no exposed wires or strands that could cause a dangerous short circuit.
- Never reverse the hot and neutral wires to prevent serious injury or death.
Fixture Assembly:
- Attach the Fixture Assembly (with LED) (F) to the Mounting Plate (A) using Set Screws (E).
- If applicable, attach the Alabaster (G) component to the Fixture Assembly (with LED) (F).
- Secure the assembly with the Finial (H) component.

WARNING/CAUTION

DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER USE.
UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY
DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

CORBETT-452-10-VPB-Fabriano-LED-Wall-Sconce-fig-1

Attach the MOUNTING PLATE (A) unto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
Attach the Ground wire Green) to the ground inside the outlet box Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Connect the white fixture lead to the neutral (Generally white wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I” below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
Attach the FIXTURE ASSEMBLY (WITH LED) (F) to the MOUNTING PLATE (A) and secure with the SET SCREWS (E).
Attach the ALABASTER (G) to the FIXTURE ASSEMBLY (WITH LED) (F) of the fixture and secure with the FINIAL (H).
Restore power to the outlet at the breaker or fuse box.