451-26-VGL Julieta Wall Sconce By Corbett Lighting User Manual
- June 13, 2024
- Corbett Lighting
Table of Contents
LIGHTING GROUP
Hudson Valley Lighting
Troy Lighting Mitzi
Corbett Lighting
451-26-VGL Julieta Wall Sconce By Corbett Lighting
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
JULIETA
451-26
Installation Instructions
FIXTURE INSTALLATION
- Attach the CROSSBAR (A) unto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted fo the structure of the building. Thread the HEX NUT (E) onto the NIPPLE (C) along with TOOTH WASHER (D), then thread the NIPPLE (C} onto the CROSSBAR (A). Adjust the NIPPLE (C} so that threads extends 1/4* beyond the FIXTURE ASSEMBLY (I).
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (F} on the CROSSBAR (A). NEVER CONNECT GROUND WIRE TO “HOT WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (G). Starting 1’ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUITI
- Connect the black fixture eads to the hot Generally black} wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Attach the FIXTURE ASSEMBLY (1) to the CROSSBAR (A) and secure with BARREL NUT (H).
- Attach the GLASS FLOWER (J} to the FIXTURE ASSEMBLY (|) and secure using the SOCKET COVER (K} and SOCKET RING (L}.
- Screw the BULB (M) into the SOCKET of the FIXTURE ASSEMBLY (I). THIS AXTURE IS RATED FOR 40 WATT TYPE B LAMP (G16.5 RECOMMENDED). DO NOT EXCEED THE RECOMMENDED WATTAGE!
- Restore power to the OUTLET at the breaker or fuse box.
PART(S) | REPLACEMENT PART NAME | NUMBER |
---|---|---|
A,B,C,D,E,F,G,H | HARDWARE KIT | HDW-451-26 |
1,K,L | FLOWER ASSEMBLY | GAS-451-26 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>