EVENT LIGHTING TSUNAMI-IP Outdoor LED Tilt Moving Head User Manual
- June 13, 2024
- EVENT LIGHTING
Table of Contents
EVENT LIGHTING TSUNAMI-IP Outdoor LED Tilt Moving Head User Manual
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time.
Information and specifications within this manual are subject to change
without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version: 1 (1 September 2022)
Safety Instructions
Warning
-
Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
-
Do not look at the light source when the device is on.
Caution: This unit’s housing may be hot during and after operation. -
Install this device in a location with adequate ventilation, at least 50 cm from adjacent surfaces.
-
Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
-
Use a safety chain when mounting this device overhead.
-
This product is rated IP65, meaning it is protected against dust and water jets from all directions. Do not operate this device in any location where excessive heat or water beyond the IP65 specification may affect it.
-
Do not operate this device if the housing, lenses, or cables appear damaged.
-
Do not connect this device to a dimmer or rheostat.
-
ONLY connect this device to a grounded and protected circuit.
-
ONLY use the hanging bracket to carry this device.
-
In case of a serious operating problem, stop using immediately.
-
The maximum ambient temperature is 40° C. Do not operate this device at higher temperatures.
Power Input and Power Linking
This device has an auto-switching power supply that works with input voltage
range of 100~240 VAC, 50/60 Hz.
Link up to a maximum of 8A. Do NOT exceed this.
Product Installation
- This fixture can be mounted in many orientations provided each individual fixture is secured by the use of correct mounting bracket.
- Use a safety chain when mounting this device overhead.
Dimensions
Lux Chart
Menu Operation
Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select / Move down a level.
Menu
DMX Chart
This fixture is controlled by the universal DMX 512 protocol. The DMX address is the first channel used to receive instructions from the external controller. For independent control, each fixture must be assigned a unique address for each of its control channels. For example, this device has three channel modes: 7/14/42, if it’s set to 7 channel mode, and there are several fixtures need to be independently controlled, we just simply address first fixture at 1, and second fixture at 8, third one at 15, etc.
- If multiple fixtures have the same DMX address, they will behave synchronically.
- Display will flash when no DMX signal is received.
Technical Specifications
Photometrics
- Light Source:
- RGB: 480x SMD5050 0.5W 3-in-1 LEDs
- Strobe: 144x 5W White LEDs
- Beam Angle: 117°
- Output:1,800 lux @ 5m
- LED Lifespan: 50,000 hours
Effects
- Dimming: 0~100%
- Strobe: 0.3-20 Hz
Movement
- 8 / 16 bit movement
- Tilt: 270°
Power
- Input Voltage: 100~240V AC, 50/60 Hz
- Power Consumption: 1,000 W
- Connection: True1 in/out
Control
- Protocol: DMX512
- Operation Modes: DMX, auto, manual, sound active, master/slave
- DMX Channels: 7/14/42
- Interface: 3-pin XLR in & out
- Display: 4-button 2.4-inch LCD control panel
- Cooling: Fan
Housing
- Materials: Metal & Flame retardant ABS
- Finishing: Matte black
- IP rating: IP65
- Net Weight: 12 kg
Warranty
Please refer to your local dealer or please contact Event Lighting Pty Ltd.
www.event-lighting.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>