HUDSON VALLEY MDS810-AGB Somerset LED Semi Flush Mount Instruction Manual
- June 13, 2024
- HUDSON VALLEY
Table of Contents
HUDSON VALLEY MDS810-AGB Somerset LED Semi Flush Mount
Product Information Product Name: Somerset MDS810
Manufacturer: Hudson Valley Lighting Group
Brands: Hudson Valley Lighting, Troy Lighting, Mitzi, Corbett Lighting
Website: www.hvlgroup.com
Product Usage Instructions
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Ensure that the junction box is securely mounted to the building structure. The fixture is designed to be mounted on a standard round or octagon junction box.
- Attach the Ground wire (Green) to the ground inside the outlet box (generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). Never connect the ground wire to the hot wire to avoid serious injury or death.
- Connect the white fixture lead to the neutral wire (generally white) in the outlet box. Fasten the wires together using an approved fastener (WIRE NUT) (D). Starting 1 inch below the fastener, tightly wrap the connection with electrical tape to seal the end of the fastener. Make sure there are no exposed wires or strands that could cause a dangerous short circuit.
- Connect the black fixture leads to the hot wire (generally black) in the junction box. Fasten the joined wires as in the previous step. Never reverse hot and neutral wires to avoid serious injury or death.
- Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the BALL NUTS (E).
- Screw the BULB (G) into the SOCKET of the fixture. Ensure not to exceed the recommended wattage of 8 watts for type B lamps.
- Lift the ALABASTER (H) up to the FIXTURE ASSEMBLY (F) and secure with the RING (I) and FINIAL (J).
- Restore power to the outlet at the breaker or fuse box.
| Replacement Parts Part Number | Part Name |
|---|---|
| HDW-MDS810 | Hardware Kit |
| RNG-MDS810 | Ring |
| FIN-MDS810 | Finial |
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
FIXTURE INSTALLATION
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D,E | HARDWARE KIT | HDW-MDS810 |
| I | RING | RNG-MDS810 |
| J | FINIAL | FIN-MDS810 |
- Attach the MOUNTING PLATE (A) unto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Attach the Ground wire (Green to the ground inside the outlet box Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Connect the white fixture lead to the neutral (Generally white wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I* below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
- Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Attach the FIXTURE ASSEMBLY (F) to the MOUNTING PLATE (A) and secure with the BALL NUTS (E).
- Screw the BULB (G) into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 8 WATT TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
- Lift the ALABASTER (H) up to the FIXTURE ASSEMBLY (F) and secure with the RING (I) and FINIAL (J).
- Restore power to the outlet at the breaker or fuse box.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>