Alarm ADC-VDB7808 Wireless Video Doorbell Instruction Manual

: June 13, 2024
: ALARM

Table of Contents

In the Box
Pre-Installation Checklist
Installation
Charging The Battery
**Button light guide
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Smart Home Security
Battery Video Doorbell
Installation Manual
Installation Support: 877-998-1457
AAA.com/SmartHome-Install Alarm ADC-
VDB7808 Wireless Video Doorbell

In the Box

ADC-VDB780B Wireless Video Doorbell
ADC-VDB780B mounting plate
10° tilt wedge
Battery pack
Charging cable
Mounting screws (2)
Mounting anchors (2)
Wedge screws (4)
Quick start guide

Pre-Installation Checklist

ADC-VDB780B and included accessories
Drill/Screwdriver
Level
Pencil
An installed Alarm.com Smart Chime (ADC-W115C) – if you have not installed the Alarm.com Smart Chime yet, do that now. For installation instructions, see Alarm.com Smart Chime (ADC-W115C) – Installation Guide
Wi-Fi connection to broadband (Cable, DSL, or Fiber Optic) internet
A computer, tablet, or smartphone with Wi-Fi

Installation

Power on the Wireless Video Doorbell
Note : The Alarm.com Smart Chime (ADC-W115C) is required for installation.

Verify that there is an ADC-W115C enrolled on the account. For installation Chime (ADC-W115C) – Installation Guide. instructions, see Alarm.com Smart
Remove the Wireless Video Doorbell (VDB780B) from the packaging.
Separate the battery pack from the VDB780B body.
Activate the battery by plugging in the Micro USB charger to a wall outlet and connecting it to the battery.
Check the top of the battery pack for a blue protective ﬁlm. If present, please remove the ﬁlm and discard it.
Press the doorbell button on the front of the battery. If the button LED alternates between red and blue, the battery pack must be recharged prior to completing the installation. For more information, see Charging the battery
If the button LED isn’t alternating blue and red, reconnect the battery pack to the VDB780B body.
After the button LED stops ﬂashing red, press and release the doorbell button and ensure the LED lights up red.

Connect the Wireless Video Doorbell to the Alarm.com Smart Chime

Ensure the Wireless Video Doorbell (VDB780B) is less than 10 feet away from the Alarm.com Smart Chime (W115C).
Conﬁrm that the W115C has been installed and associated with an account.
To enable WPS mode, press and hold the VDB780B doorbell button ﬁrmly for greater than 30 seconds. The LED will begin ﬂashing blue.
Press and release the WPS button located on the side of the W115C to enable WPS mode. The WPS LED will begin ﬂashing rapidly.
If the pairing is successful, the W115C Devices LED will quickly blink 3 times, and the VDB780B LED will begin blinking red and then turn solid green.

Enroll the Wireless Video Doorbell to the Account

Add the Wireless Video Doorbell (VDB780B) to the account by selecting the account in MobileTech or by using a web browser and entering the following web address: www.alarm.com/addcamera.
Select the VDB780B from the video device list or enter in its MAC address to begin adding the device. The MAC address can be located on the device, on the box, or on the reference card.
Follow the on-screen instructions to ﬁnish adding the device.

Mount the Wireless Video Doorbell
Plan, Level, & Mark
VDB780B_ﬁeld-of-view.webp

Identify a location on the side of your doorframe to mount your Wireless Video Doorbell (VDB780B). We recommend a position approximately 4 feet above the ground for an optimal ﬁeld of view.
Place the mount at your desired location.
Use a level to ensure the mount is parallel with the ground.
Use a pencil to mark the two holes of the mount.

Tip : If you have someone to help you with the setup, use the Mobile App or Customer Website to start a live stream.
You can place the VDB780B over your planned mounting position to assess the ﬁeld of view before you start drilling.
Drill

Use a 1/4” drill bit to create appropriately sized holes for the supplied anchors at your marked locations.
Insert the anchors.

Screw

Place the mount over the two anchors.
Use the supplied screws to secure the mount in place.

Attach the Wireless Video Doorbell to the Mount

Align the prongs on the back of the Wireless Video Doorbell (VDB780B) with the 4 rectangular slots in the mount.
Push the VDB780B into the slots and slide down, until the device clicks into place.
Slide the latch on the bottom of the mount to secure the VDB780B in place.

Alarm ADC-VDB7808 Wireless Video Doorbell - Align

Conﬁrm Battery Charge

If the battery was not fully charged as part of the Power on the Wireless Video Doorbell section, please remove the VDB780B and follow the instructions in the Charging the Battery section.

Charging The Battery

Charging Requirements

A 5V/1.5A USB wall charger
The supplied charging cable

Charging Steps
Note : A fully depleted battery takes approximately 7 hours to charge.

Unlatch the bottom of the mount.
Remove the VDB780B from the mount.
Separate the battery pack from the VDB780B body.
Plug the supplied micro USB cable into the battery pack.
Plug the USB end of the cable into a USB wall charger and insert the charger into an outlet.
The charging LED, located on the top of the battery pack, will be solid orange while the device is charging. The charging LED will turn solid green when charging has completed.

LED Guide

**Button light guide

**

Operational States

Mode	Description	Button LED behavior
Standby or oﬀ	The camera is in standby mode (normal operation) or the battery

is
drained and requires recharging.| Oﬀ
Local connection| The camera has a local network connection.| Solid green
No local connection| The camera does not have a local network connection.| Solid red
Low battery| The camera’s battery is low and requires a recharge.| Alternating red and blue
Connecting to network| The camera is powered on and connecting to the network.| Blinking red
WPS mode| The camera is in WPS pairing mode.
To enter this mode, press and hold the button for 30-45 seconds.| Blinking blue
AP mode| The camera is in AP pairing mode.
To enter this mode, press and hold the button for 46-60 seconds.| Blinking white
Power cycle| The camera is being power cycled.
To enter this mode, press and hold the button for 61-75 seconds.| Blinking yellow
Factory reset| The camera resetting to factory default. To enter this mode, press
and hold the button for 76-180 seconds.| Alternating red and green
Firmware upgrade| The camera’s ﬁrmware is being upgraded.| Blinking yellow rapidly

Charging States

Mode description	Top LED Behavior	Button LED behavior

Charging
The battery pack is plugged in and charging.| Solid orange| On button press
Solid green =

75% charged
Solid orange =
75%-15% charged
Alternating red and blue = <15% charged
Fully charged
The battery pack is fully charged.| Solid green| On button press , solid green
Failure charging
The battery pack stopped charging because the device was plugged in
too long. This may signal that there is an issue with your battery pack.
Remove the charging cabled and reattempt charging after an hour. If
you see the same behavior, please contact your provider.| Alternating orange and green| Alternating red and white
Under temperature
The battery pack’s internal
temperature is too cold. Please charge the battery pack in a roomtemperature setting.| Solid green| Alternating red and yellow = -20° – 0°
Over temperature
The battery pack’s internal temperature is too hot. Please charge the battery pack in a roomtemperature setting.| Solid green = -20° – 0°
Oﬀ = < -20°| Blinking red rapidly = -20° – 0°
Oﬀ = < -20°