Smekitlly BY061 Universal Ceiling Fan Remote Control Kit Instruction Manual

Smekitlly BY061 Universal Ceiling Fan Remote Control Kit

PRODUCT INFORMATION

This wall control is designed to separately control your ceiling fan speed and light brightness. There are four buttons (Hi, Med, Low, Fan Off) to control the fan speed and one button (Light) to control the light. The ON/OFF switch is to turn the power to wall control On or Off. The red indicator on the transmitter will light when any butt on is pressed.

INSTALLATION AND OPERATING INSTRUCTIONS

SAFETY PRECAUTIONS

DANGER: HIGH VOLTAGE! lbusehold electrical power can cause serious injury or death. Discormect source of electrical power to the ceiling fan by removing fuse or switching off circuit breaker. Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring, please use a qualified and licensed electrician.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with the remote control receiver are designed to accept only one 12 gauge house wire and no more than two lead wires fmn the receiver. If your house wire is larger than 12 gauge or there is nore than one house wire to cmnect to the two receiver wires, consult an electrician for the proper size wire connectors to use.
CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THE FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE OR CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.

• Do not use this wall control with solid state ceiling fans.
• Electrical source and fan must be 115/120 volts, 60 Hz.

Maximum fan motor amps: 1. 0; Maximum light watts: 300 incandescent only.

INSTALLATION OF RECEIVER (Please refer to Figure 1 before continuing .)

Manually set fan speed control to HIGH via pull chain and set light to ON via pull chain.

IMPORTANT : Fan speed and light control will not be activated by wall control if pull chains for fan and light are not set to the HIGH and ON positions, respectively.

• Disconnect source of electrical power to the ceiling fan by removing fuse or switching off circuit breaker.
• Lower ceiling fan canopy from the mounting bracket.
• Disconnect existing wiring between ceiling fan and supply at electrical outlet box.
• Lay the black antenna wire on top of the receiver and slide the receiver into the mounting bracket. (Figure 1)
• Using the wire connectors supplied, make wiring connections as follows: (Figure 2)

CONNECT TO:

• GREEN fan wire B ARE supply wire
• RED or BLACK receiver wire (AC IN L) BLACK supply wire
• WHITE receiver wire (AC IN N)  WHITE supply wire
• WHITE receiver wire (TO MOTOR N)  WHITE fan wire
• BLACK receiver wire (TO MOTOR L) BLACK fan wire WALL CONTROL
• BLUE receiver wire (FOR LIGHT) BLUE light wire (from fan)
• Wrap each wire connector separately with electrical tape as an extra safety measure.

If other fan or supply wires are different colors than those mentioned,have this unit installed by a qualified electrician.

• Push all connected wires up into outlet box. Make sure antenna:nrtei;itrieof mounting bracket.
• Re-install the canopy on the mounting bracket.

SETTING CODE ON WALL CONTROL (TRANSMITTER AND RECEIVER)

This unit has 16 different code combinations. To set the code perform these steps:

Setting the code on the wall control

• Slide code switches 1 through 4 to your choice of up or down position. (Factory setting is all up).
• Do not use this position. Use a small screwdriver or ballpoint pen to slide firmly up or down. (Figure 4)

****

****

Setting the code on the receiver

• Slide code switches to the same positions as set on your transmitter (Figure 5)

INSTALLING WALL CONTROL

• Remove wall plate, disconnect and remove the toggle switch from wall outlet box. Using the wire connectors providedleantikicahoccmnections to the wall control as shown in Figure 2. Wrap each wire connector separately with electrical tape as an extra safety wires back inside wall outlet box. Secure wall control with 2 screws provided. Attach wall plate cover with the 2 original screws.

WALL CONTROL CARE AND OPERATION

This wall control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units such as garage door openers, car alarms or security systems. If you find that your fan and light kit go on and off without using your wall control, simply change the combination code in your wall control

Operation buttons on the front panel of the wall control:

• HI button
• MED button
• LOW button
• FAN OFF button
• LIGHT button
  • for fan high speed
  • for fan medium speed
  • for fan low speed
  • for fan speed off
  • for light brightness and off

The light function is controlled by pressing the LIGHT button. Hold button down to increase or decrease light. Tap button quickly to turn light off or on. If you press the button in excess of 0. 7 second it becomes a dimmer. The light varies cyclically in 0.8 seconds. The light button has auto resume, so the light will stay at the same brightness as the last time it was turned off.

IMPORTANT : M ake sure that fan has been turned off at wall switch and then allow blades to come to a complete stop befmruernally activating the reverse switch on the fan.

TROUBLESHOOTING GUIDE

Fails to operate:

1. Power to the receiver?
2. Receiver wired correctly?
3. Manual speed control on fan in highest position?
4. Light kit switch turned on?
5. Learning process between fan and wall control may not have been successfu
   • Turn power off and repeat Section V (Automated Learning Process) above.
6. Make sure the black antenna wire rests outside of hanging bracket.

WARNING: Check to see that all connections are tight, includin ground, and that no bare wire is visible at the wire can entitthe incedes for the isound voise and ran dansate could result.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>