LABELMATE USA DISTRI-COUNT Combination Label Dispenser Counter User Manual
- June 4, 2024
- LABELMATE USA
Table of Contents
LABELMATE USA DISTRI-COUNT Combination Label Dispenser Counter
DISTRI-COUNT
Unique Label Counter/Dispenser that simultaneously counts and dispenses unpeeled labels on a tear-off bar. The softkey control panel and large display make the DISTRI-COUNT extremely easy to operate. Once the requested number of labels is counted/dispensed, the DISTRI-COUNT can immediately repeat the action or be reprogrammed to count/dispense a new number of labels.
DIMENSIONS
- H x W x D: 8.75” x 9” x 11.5” (232 x 295 x 222-mm)
MEDIA
- Alignment: left aligned
- Max roll diameter: 8” (220 mm)
- Core diameter: 1” – 4” (25 – 101-mm)
- Max width : 4.5” (115-mm)
- Min width: 0.4” (10-mm)
- Thickness: 0.003” – 0.007” (0.08 – 0.17-mm)
- Backing Paper: Tearable for use on the tear-off bar
- Max label length: 7.87” (200-mm)
GENERAL
- Power Supply: SYS1548-6515-T3 (PS-1545) 100-240V – 50/60Hz. Output 15VDC 4.33A
- Limited Warranty: 3 Years Parts & labor, 1 Year on Power Supply
THIS MANUAL IS VALID FOR THE FOLLOWING PRODUCTS:
P/N MODEL DESCRIPTION
- 50-269-0001 DISTRI-ST DISTRI-COUNT with standard label sensor for opaque labels.
- 50-269-0002 DISTRI-U DISTRI-COUNT with label sensor for transparent and black marked labels.
SAFETY INSTRUCTIONS
- This product is a Label Counter/Dispenser. It should be used only to count labels of the recommended dimensions and weight in an indoor, dry environment.
- Unplug the power cord prior to any manipulation.
- Use on a flat surface only.
- Ensure sufficient ambient light within the working area.
- The unit can be used in ambient temperatures of 35º to 105º F. (2º to 40º C)
- Connection of the Winder to the power source must comply with all local regulations.
- Special caution in cleaning-mode: Access to moving parts can be dangerous! Wearing safety gloves is recommended.
- Do not use sharp objects or tools to clean the unit as they can damage the rubber platen roller.
NOTE: Figures referenced below can be seen on Page 4
STEP 1 : LOADING THE MEDIA ROLL
- Remove the media roll guide and media path guide. (1 & 3)
- Open the mechanism cover. (7)
- Load the media as displayed and put the guides back. (FIG.3)
- Load the labels until they are approximately 0.4” out of the DISTRI-COUNT (FIG.4)
- Close the mechanism cover again. (FIG.4)
STEP 2 : AUTOMATIC CALIBRATION
-
Adjust the sensor position (4) with the adjustment knob (5) so it is able to detect your labels and the label
gap or a black-mark on the liner material. -
Switch on the power to start the automatic calibration of the label size.
-
The DISTRI-COUNT presents the first label precisely on the TEAR-OFF-BAR (8) and is now ready for use.
-
Opening and closing the mechanism cover (7) will initiate a new calibration process.
PRESET MODE: COUNTING FIXED NUMBER OF LABELS
- Use the 4 arrow buttons (FIG.1) on the control panel to set the desired number of labels and then press the START/STOP button.
- The DISTRI-COUNT now presents the requested number of labels on the TEAR-OFF-BAR. Tear-off downwards.
- The DISTRI-COUNT counter resets to the initial requested quantity for a new job. Press START/STOP to repeat. If you want a number of labels, press the CLEAR button and enter the new desired number.
COUNT MODE: COUNTING LABELS ON ROLL
- Make sure the DISTRI-COUNT Display is on “0000” by pressing the CLEAR button or initiating a new calibration.
- Press the COUNT/STOP button to start counting.
- Press the COUNT/STOP button again for pausing/counting.
OBTAINING THE TOTAL COUNT & RESETTING THE COUNTER
- Press and hold the CLEAR button on the keypad. After 2 seconds the display will show the total job quantity.
- To reset the count to zero, press and hold the CLEAR button for 2 seconds and press the arrow key just above.
MAINTENANCE
- In the event of dust or adhesive build-up on the platen roller or other parts of the driving mechanism, use a dust-free wipe/tissue with isopropyl-alcohol to clean.
- For easy cleaning, power-off. When powering back on, press and hold the feed button; the platen roller now turns with open cover. WARNING: Direct access to rotating parts can be dangerous. Do not touch parts unless the machine is powered off and unplugged.
PRODUCT LIMITED WARRANTY
| WARRANTY PERIOD | PRODUCTS COVERED |
|---|
5-Years
| à “CAT” and “Mini CAT” Label Rewinders.
à “UCAT” Label Unwinders.
3-Years
| à Label Counters ( Excluding Counter Displays and Encoders )
à Label Dispensers ( Excluding Counter Displays )
à Label Slitters ( Mechanical Parts Only – excluding Counter Displays )
à Reel-to-Reel Machines ( Excluding Counter Displays and Encoders )
à Print Mechanisms ( Excluding Counter Displays and Encoders )
à Label Applicators ( Excluding Polyurethane Rollers )
à Quick-Chucks
1-Year
| à Power Supplies, AC/DC Adaptors and Transformers
à Counter Displays
à Encoders
à Any other products or parts not specified herein
180 Days| à Out-of-Warranty Repairs
Labelmate USA warrants to the original end-user customer that Labelmate USA
products will be free from defects in materials and workmanship for the
duration described
herein below. Labelmate USA’s Limited Warranty covers only those defects that
arise as a result of the normal use of the products and does not cover any
other problems,
including those that arise as a result of
- improper maintenance or modification;
- parts or supplies not provided or supported by Labelmate USA;
- operation outside the products’ specifications; or
- unauthorized repair, modification or misuse.
Use of any unauthorized accessory or attachment will void coverage. The Warranty period for all products commences on the date of shipment from Labelmate USA and accrues to the original end-user customer. Warranty coverage is nontransferable and terminates immediately upon rental, resale or any other change in ownership. Original purchase documentation must be retained for coverage verification. In the event Labelmate USA substantiates, during the applicable Warranty period, a defect in any product which is covered by Labelmate USA’s Warranty, Labelmate USA shall repair or replace the product, at Labelmate USA’s option. Labelmate USA retains sole discretion to determine whether or not a product is defective. In no event shall Labelmate USA has any obligation to repair or replace until the customer returns the defective product to Labelmate USA. The customer assumes any and all responsibility and liability associated with the transportation of products for service under this Warranty. In the event your product requires service or you have questions regarding Warranty coverage, please call toll-free 877-833-7149 inside the United States, or+1 702-435-8535 outside the United States. LABELMATE MAKES NO OTHER WARRANTY OF ANY KIND, WHETHER EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, AND/OR FITNESS FOR A PARTICULAR PURPOSE. NO OTHER PERSON, AGENT, DEALER OR RESELLER IS AUTHORIZED TO GIVE ANY WARRANTIES ON BEHALF OF LABELMATE. ANY OBLIGATION TO WARRANTY OTHER THAN THAT SPECIFICALLY ADDRESSED HEREIN IS DISCLAIMED.
Toll Free: 877.833.7149
Direct: 702.435.8535
info@labelmateusa.com
12A Sunset Way Henderson, NV 89014
www.labelmateusa.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>