AIGOSTAR 100801TYQ Led TV Backlight User Manual
- June 4, 2024
- aigostar
Table of Contents
AIGOSTAR 100801TYQ Led TV Backlight
Please read this manual carefully before operating your product. Even you pass
your product to others, please also follow below instructions and operate
safety. We are not take responsibility like improper use or not to follow this
operation manual and safety advice lead to damage to property or even injury
to persons. Any warranty claim is also deemed as void.
Please check whether the product is complete. If you find any defects, please
contact salesman immediately and make sure the package is ok.
PARTS
- 4*0.SM Strip light(One of strip light with 1 M USB wire)
- 3*30CM connect wire
- 3*4 PIN
- One remote control
Product Description
Note:
-
The way to test the photoelectricity parameter value of the product:
Take O.Sm strip light and test it with SV DC power supply, and read the bare light source data. -
Test conclusion:
Goods Code| DC Voltage| Power
---|---|---
100801TYQ| 5V| 1.2W -
Class III
WARNING
-
THE PRODUCT IS NOT A TOY, PLEASE TAKE THE PRODUCT AND PACKAGE FAR AWAY FROM ADULT OR CHILDREN WHO CAN NOT EVALUATE THE RISK.
-
THE PRODUCT NEED TO INSTALL BY QUALIFIED ELECTRICIAN AND INSTALLED IN ACCORDANCE WITH LOCAL REQUIREMENTS.
-
PLEASE TURN OFF THE POWER SUPPLY BEFORE ANY OPERATIONS.
-
DO NOT LOOK DIRECTLY INTO THE LIGHT.
-
THE PRODUCT NEED TO BE CLEANED CORRECTLY.
AVOID CLEANING THE PRODUCT WITH SHARP OR ABRASIVE DETERGENT. -
ELECTRONIC WASTE AND ELECTRONIC DEVICE CANNOT DISPOSE WITH ORDINARY HOUSEHOLD WASTE.
-
THE REMOTE CONTROL CONTAIN NON-RECHARGEABLE BATTERIES, PLEASE MAKE SURE KEEP AND DISPOSE IT CAREFULLY. DO NOT THROW THE BATTERY INTO FIRE OR IMMERSE IN WATER.
-
PLEASE PUT THE PRODUCT ON DRY SURFACE, KEEP SAFETY DISTANCE AWAY FROM OVEN AND HEATER TO AVOID EXTREME TEMPERATURE, ELECTROSTATIC INTERFERENCE, STRONG IMPACT AND HIGH VOLTAGE.
-
ONCE THE PRODUCT BROKEN OR MALFUNCTION, PLEASE TURN IT OFF IMMEDIATELY AND CONTACT QUALIFIED ELECTRICIAN OR SERVICE PROVIDER TO DEAL WITH.
-
IF FIND LEAKING BATTERY, PLEASE MAKE SURE AVOID OUR SKIN, EYES AND MUCOSA TO TOUCH THE BATTERY’S ACID. IN CASE OF CONTACT WITH SKIN, WASH IMMEDIATELY WITH PLENTY OF WATER.
Parameter
- Battery type: CR 2025 3V 165MA
- Remote control range: About Sm
- LED strip: IP65
- USB wire: I P20
Replace the battery of remote control:
We suggest to replace the battery when the remote control performance reduction. Before insert the battery, please make sure the touch point between remote control and battery are clean. And clean them if necessary.
- Slide the battery cover in the arrow direction indicated and disassemble.
- Take down the exhausted battery and install new battery(CR 2025) if necessary. Please pay attention to polarity(+/-) when replacing batteries.
- Install the battery into remote control.
Installation
- Check the LED light strip if is working correctly.
- Connect the LED strip into right connector(see below diagram) and insert USB into TV. Check all LED strips and remote control if is working properly.
- After checking the strip light and remote control working properly and disconnect the USB interface, then stick the LED strip on TV. When finished install LED strip, only need insert the USB interface into TV and ready to use it.
Pay attention to the arrow direction!
When connecting to the short connector, please make sure each arrow points to DC SV on the same side.
Fixed the LED strip light LED strip light with double adhesive tape on the back. Peel off protective foil from the tape and fix it to the location you needed.
2-year quality guarantee under the correct operations.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>