BORMANN BWM3063 Pipe Adhesive User Manual

BORMANN BWM3063 Pipe Adhesive

Product Information:

The BWM3063 is a bonding tool used for melting pipelines and pipe fittings. It is designed for use with a voltage/frequency of 220 V ~ 50 Hz and has a power of 1500 W. The tool consists of several main parts including the chassis, indicator, heat insulation cover, heating board, support board, and cable.

Product Usage Instructions:

1. Installation & beaten the bonding tool: Choose the appropriate bonding tool based on the required specification. Install the bonding tool by using the inside hex screw, ensuring not to overtighten it to avoid damaging the thread.
   The smaller end of the bonding tool should be installed first. When changing the bonding tool during operation, exercise caution.

2. Fix the melting connection device: Attach the melting connection device to the support board, which is specially designed to fit into the fix-groove in the chassis. This ensures stability and ease of operation for the user.

3. Put through power and heat: Connect the tool to a power supply with an earth wire. Turn on the power, and the red indicator lamp will illuminate, indicating that the melting connection device is heating up. When the green indicator lamp is on, it means that the device has stopped heating. After a while, the red indicator lamp will turn on again, indicating that the melting connection device has reached the desired temperature and is ready for use.

4. Melting pipeline: Use a cut device to cut off the pipeline. Insert both the pipeline and pipe fitting into the bonding tool simultaneously and apply pressure for several seconds (refer to table 2 for specific times). Then, quickly pull them out perpendicular to their direction of insertion. Take care not to exert excessive force while pulling to prevent the head from getting crooked. Note that within the fixed processing time, the connection can be adjusted, but rotating it is prohibited.

Please refer to the provided table for specific details regarding the size of the bonding tool, pipeline specifications, internal diameter of concave head, internal diameter of protruding head, and heat making depth.

For more information and support, please visit www.nikolaoutools.gr .

Main Parts

1. Chassis
2. Indicator
3. Heat insulation cover
4. Heating board
5. Support board
6. Cable

Technical Data

• Voltage/Frequency: 220 V ~ 50 Hz
• Power: 1500 W

The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.

• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

Caution

1. Please check the outer cover and cables of the melting connection device first. Don’t use it if it is damaged.
2. Melting Connection device adopts the single-phase tertiary safety flat plug, user can’t change the plug at will, the power supply should have an earth connection.
3. Melting Connection device is prohibited to use outside when it is raining, and prevent water & various kinds of liquid from entering into meeting connection device.
4. Operator must operate and change bonding tool with wearing gloves while the device is in working normally.
5. The device should be paid attention to laying, prevent personnel and property from damaging.
6. Chassis of melting connection device can’t be opened willingly, so as not to got an electric shock and destroy the safety performance of the machine.
7. If indicator lamp are not changed for a long time, it shows the device is in non-normal working state, it should be quit work immediately and cut off the power.
8. Check inserting ability regularly in the course of using, the device should be stopped working as soon as basic insulating is destroyed.
9. The device should be sent to manufacturer to repair if it is out of order. Product Structure

Size of bonding tool: see table 1
unit: mm

Pipeline specification| Internal diameter of concave head| Internal diameter of protuding head| Heat making depth
---|---|---|---
20| 14| 5| 4
25| 16| 7| 4
32| 20| 8| 4
40| 21| 12| 6
50| 22,5| 18| 6
63| 24| 24| 6

1. Installation & beaten the bonding tool.
   According to specification needed, to install the corresponding bonding tool with inside hex screw, screw can’t be twisted too tight while cool installing, oth- erwise, the thread of bonding tool will be damaged easily. Generally, the small is in front of the big while installing. In working state, be careful while changing the bonding tool.

2. Fix the melting connection device.
   Melting connection device is matched with support board special-purposely, the board is fixed by the fix-groove in the chassis, simple & convenient. Make the operator operate be easier with step on the support board.

3. Put through power and heat
   Turn on power (caution: power supply with earth wire), the red indicator lamp is on, it shows the melting connection device is heating, if the green indicator is on, it shows the device stop heating. After a while, the red indicator lamp is on again, it shows melting connection device enter into the state of control & keep temperature, it can begin to work.

4. Melting pipeline
   Cutting off the pipeline with cut device, advance the pipeline& pipe fitting in the bonding tool in same time and beaten for several seconds (see table 2) and then, pull out them rapidly to move forward perpendicularly. It is not too big to exert while moving forward in order to prevent the head being crooked.

Note: within fixed processing time, the connection can be corrected, however, it is prohibited to rotate. Melting connection request.

WARRANTY

This appliance is a quality product. It was designed in compliance with current technical standards and made carefully using normal, good quality materials. The warranty period is 24 months for non-professional use and 12 months for professional use and commences on the date of purchase, which can be verified by the receipt, invoice or delivery note. During this warranty period all functional errors, which, despite the careful treatment described in our operating manual, are verifiably due to material flaws, will be rectified by our after-sales service staff. The warranty takes the form that defective parts will be repaired or replaced with perfect parts free of charge at our discretion. Replaced parts will become our property. Repair work or the replacement of individual parts will not extend the warranty period not will it result in a new warranty period be- ing commenced for the appliance. No separate warranty period will commence for spare parts that may be ted. We cannot offer a warranty for damage and defects on appliances or their parts caused by the use of excessive force, improper treatment and servicing. This also applies for failures to comply with the operating manual and the installation or spare and accessory parts that are not included in our range of products. In the event of interference with of modifica- tions to the appliance by unauthorized persons, the warranty will be rendered void. Damages that are attributable to improper handling, overloading, or natural wear and tear are excluded from the guarantee. Damages caused by the manufacturer or by a material defect will be corrected at no charge by repair or by providing spare parts. The prerequisite is that the equipment is handed over assembled, and complete with the proof of sale and guarantee. For a guar- antee claim, only use the original packaging. That way, we can guarantee quick and smooth guarantee processing. Please send us the appliances post-paid or request a Freeway sticker. Unfortunately, we will be unable to accept appliances that are not postpaid. The warranty does not cover parts that are subject to natural wear and tear. If you wish to make a warranty claim, report faults or order spare parts or accessories, please contact the after-sales center: Subject to change without prior notice.

WWW.NIKOLAOUTOOLS.GR

References

• BORMANNTOOLS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>