COOPER Lighting Solutions IB520143ML Portfolio LuxWire Cylinders Instruction Manual

: June 13, 2024
: COOPER Lighting Solutions

Table of Contents

COOPER Lighting Solutions IB520143ML Portfolio LuxWire Cylinders
Product Information
Product Usage Instructions
Up Down Installation Instructions
Trim
Cleaning
Wiring Diagrams
Dimming
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

COOPER Lighting Solutions IB520143ML Portfolio LuxWire Cylinders

Product Information

Product Model: IB520143ML
Product Name: PORTINFS O# LIOTM
Product Description: This product is a lighting fixture that requires installation and maintenance by a qualified electrician. It is designed to be installed in accordance with the applicable installation code and should only be handled by individuals familiar with the construction and operation of the product.

Product Safety Warnings:

Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily injury, and property damage.

Product Usage Instructions

Up Down Installation Instructions

Cylinder comes fully assembled when received. To install, remove the #8-32 nut located in the center of the 2 aircraft cables. The canopy can fall out of the way to expose the mounting strap. (See Figure 1)
Connect the mounting strap to the J-Box (supplied by others) with 2 #8-32 screws. (See Figure 2)
For options with the driver in the canopy, there is a splice cover to provide a barrier to the ceiling and the driver isattached to the mounting strap. Make connections to Driver following local code and referring to the wiring diagrams mentionedin the electrical section. (See Figure 3)
For remote driver options, connect the remote driver to J-Box following the instructions provided in the kit. Then connect the remote harness to the aircraft cable using the orange connectors attached to the ends of each side.
Once wiring is complete, slide the canopy back up to the ceiling and secure it with the #8-32 nut. Clip zip ties that are holding the aircraft cable so that the cylinder can hang freely.
To adjust height, use the cable fittings located on the cylinder body. Push the fitting to pull the cable through and be sure to clip the ends so that the cable does not contact any metal components.
Heat shrink is provided to insulate the cables from the cylinder body. It is recommended to put the heat shrink where the cable contacts the cylinder next to the cable fitting.

Down Light Installation Instructions

Cylinder comes fully assembled when received. To install, remove 2 #8-32 flat head screws from the canopy located outside ofthe 2 aircraft cables. The canopy can fall out of the way to expose the mounting strap. (See Figure 4)
To adjust height, the cylinder top needs to be removed by removing 4 screws, then use the cable fittings located on the cylinder top. Push the fitting to pull the cable through and be sure to clip the ends so that the cable does not contact any metal components. Then reinstall the cylinder top.

Trim

Remove lower trim from protective packaging. Rotate side clips(3) outwards. (See Figure 5) Remove LED Engine from protective packaging.

WARNING

Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Minimum 90°C supply conductors.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.

DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
NOTICE: Fixture may become damaged and/or unstable if not installed properly.
Note: Specifications and dimensions subject to change without notice.
Note: This fixture should be supported by main runners or other structure that is capable of supporting fixture weight of 40 Ibs.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Up Down Installation Instructions

Cylinder comes fully assembled when received. To install remove #8-32 nut located in the center of the 2 aircraft cables. The canopy can fall out of the way to expose the mounting strap. (Figure 1)
Connect the mounting strap to the J-Box (supplied by others) with 2 #8-32 screws. (Figure 2)
For options with the driver in the canopy, there is a splice cover to provide a barrier to the ceiling and the driver is attached to the mounting strap. Make connections to Driver following local code and seeing the wiring diagrams mentioned in the electrical section. (Figure 3)
4. For remote driver options, connect remote driver to J-box following the instruction provided in the kit. Then connect the remote harness to the aircraft cable using the orange connectors attached to the ends of each side.
Once wiring is complete, slide the canopy back up to the ceiling and secure back with the #8-32 nut. Clip zip ties that is holding the aircraft cable, so the cylinder can hang free.
To adjust height, use cable fittings located on the cylinder body. Push the fitting to pull the cable through and be sure to clip the ends so the cable does not contact any metal components.
Heat shrink is provided to insulate the cables from the cylinder body. Recommend putting the heat shrink where the cable contact the cylinder next to cable fitting.

Down Light Installation Instructions

Cylinder comes fully assembled when received. To install remove 2 #8-32 flat head screws from canopy located outside of the 2 aircraft cables. The canopy can fall out of the way to expose the mounting strap. (Figure 4)
Connect the mounting strap to the J-Box (supplied by others) with 2 #8-32 screws. (Figure 2)
For options with the driver in the canopy, there is a splice cover to provide a barrier to the ceiling and the driver is attached to the mounting strap. Make connections to Driver following local code and seeing the wiring diagrams mentioned in the electrical section. (Figure 3)
For remote driver options, connect remote driver to J-box following the instruction provided in the kit. Then connect the remote harness to the aircraft cable using the orange connectors attached to the ends of each side.
Once wiring is complete, slide the canopy back up to the ceiling and secure in place with 2 #8-32 flat head screws. Clip zip ties that is holding the aircraft cable, so the cylinder can hang free.
To adjust height, the cylinder top needs to be removed by removing 4 screws, then use cable fittings located on the cylinder on the cylinder top. Push the fitting to pull the cable through and be sure to clip the ends so the cable does not contact any metal components. Then reinstall to cylinder

Trim

Remove lower trim from protective packaging. Rotate side clips (3) outwards. (Figure 5) Remove LED Engine from protective packaging
Insert LED engine on to trim assembly. Align post on LED engine with slot on trim assembly. (Figure 6)
Rotate side clips (3) into place to securely attach trim assembly to LED engine. (Figure 7)
Plug in the luminaire quick disconnect on the module. (Figure 8)
Find the green tether inside cylinder and attach it to the heatsink using the screw and lock washer located in the envelope attached to the tether. (Figure 9)
Install the LED Engine and trim assembly by inserting the torsion springs into the spring receivers located inside the housing. (Figure 10)

Cleaning

To Clean Trims:
Gently wipe with soft, clean, dry lint-free cloth to remove dust.
Wipe with mild detergent solution on a soft, clean cloth to remove fingerprints and stains.
Rinse with clean water and dry with soft, clean, dry lintfree cloth.

Electrical Connection
Make certain no bare wires are exposed outside of wire nut
connectors.

Provide electrical service according to the “National Electrical Code” or your local electrical code to the cylinder housing assembly. Supply wire insulation must be rated for at least 90°C.
Connect supply lead wires to cylinder housing lead wires (line, neutral and ground) in the fixture using properly sized wire nuts. Be careful not to leave any bare conductors outside of the wire nut connectors.
Connect white to white, black to black, and green (from electrical service) on the supply side to the green wire in the cylinder housing assembly.

Wiring Diagrams

For D010TR Driver
For D010TE Driver
DL3 Driver
For D010 Driver
For D5LT Driver
For DMX Driver
For DE010 Driver
For DL2 Driver
For DLE Driver

Constructions built before Jan 2022 may have gray wire for 0-10 dimming control present. In these cases, the installer will label the gray building wire as a 0-10 dimming wire and connect to our product’s pink 0-10V dimming control wire. Reference NFPA70 (2020 NEC), section 410.69.

Dimming

The Portfolio D010 Cylinders can be dimmed with many standard 0-10V DC dimming controls. The Portfolio D010TE Cylinders can be dimmed with many trailing edge dimmers and 0-10V DC dimming controls. The Portfolio DL2 Cylinders can be dimmed with Lutron 2-wire forward phase controls. The Portfolio D5LT Cylinders can be dimmed with Fifth Light and DALI compatible controls. The Portfolio DMX Cylinders can be dimmed with DMX compatible controls. The Portfolio DE010 Cylinders can be dimmed with 0-10V DC dimming controls but are NOT to be dimmed using line voltage dimmers. The Portfolio *DLE Cylinders can be dimmed with Lutron EcoSystem® digital controls. To be assured of the latest information regarding luminaire and dimmer compatibility, please reference the Portfolio LEDwebsite: www.portfolio- lighting.com.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device complies with ISED ICES Standard Canada ICES-005 (A) / NMB-005 (A) or ICES-005 (B) / NMB-005 (B) depending on driver selected. Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Cooper Lighting Solutions