Westfalia WBFW7.2 7.2 8 V Mini Drill And Grinder User Guide

: June 13, 2024
: Westfalia

Table of Contents

WBFW7.2 7.2 8 V Mini Drill And Grinder
TECHNICAL DATA
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

8 V Mini Drill and Grinder
Art. 99 20 18
Original Instructions

WBFW7.2 7.2 8 V Mini Drill And Grinder

Westfalia WBFW7 2 7 2 8 V Mini Drill And Grinder -
Description

Clamping chuck
Light
Spindle lock
On/Off-Switch
Speed regulator
Battery charge indicator
USB-C charging socket

Dear Ladies and Gentlemen,
Instruction manuals provide valuable hints for using your new device. They allow you to use all functions to avoid misunderstandings and damage. Please take the time to read this manual carefully and keep it for future reference.
If you pass the device on to third parties, enclose these instructions.

Unbox device
Loading the battery
Insert tool
Switch on the device
Set speed
Battery charge indicato

Westfalia WBFW7 2 7 2 8 V Mini Drill And Grinder -
FIGURE

TECHNICAL DATA

Nominal speed| 5000 – 31 000 min
-1
---|---
Dimensions| 205 x 38 x 35 mm
Weight (Device)| 260 g
Chuck| 3,2 mm
Sound Pressure
Level| LpA = 63 dB(A)
KpA = 3 dB(A)
Sound Power Level| LwA = 74 dB(A)
KwA = 3 dB(A)
Hand Arm Vibration| ah = 2,5 m/s²
K = 1,5 m/s²
Battery capacity| 1000 mAh
Charge time| 3-5 hours
USB socket| Type C
Battery voltage| 7,2 V ****

The declared vibration total value and the declared noise emission values have been measured in accordance with a standard test method and may be used for comparing one tool with another. The declared vibration total value may also be used in a preliminary assessment of exposure.
Please note the included General Safety Notes and the following safety notes to avoid malfunctions, damage or physical injury.
**** Please also note the safety instructions in the operating instructions for cordless tools.

Please read these operating instructions carefully and only use the device in accordance with these instructions.
Use protective equipment including safety goggles and hearing protection when operating the device. If the operation of the device causes discomfort or discomfort, stop working immediately and investigate the cause.
Dispose of unnecessary packaging material or keep it in a place that is out of the reach of children. There is a risk of suffocation!
Persons with limited physical, sensory or mental abilities may not use the device unless they are supervised and instructed by a supervisor.
Use metal detectors and voltage detectors to locate hidden power, water, and gas lines. Do not touch live components or conductors.
Ensure that the work area is adequately lit.
Make sure the cutter is securely fastened in the clamping chuck. Loose tool bits can be thrown out of the machine and present a safety hazard.
Place the tool on the workpiece before switching on the device.
Before starting work, check that there is enough clearance under the workpiece for the cutter.
Do not put pressure on the device: this will shorten its lifespan.
Cutter can get very hot during operation. There is a risk of burns.
Allow tool bits to cool before touching.
Never use your hands to remove chips or scrap material near the tool insert.
If you are interrupted while operating the cutter/driver, complete the step you have started and turn off the power before you look up.
Whenever possible, use fixtures or a vise to securely fasten the workpiece.
Regularly inspect the clamping chuck for signs of wear and damage. Have defective parts repaired or replaced by an authorized workshop.
Always wait until the application tool has come to a complete standstill before putting the device down.
Check all screws, nuts and other fasteners for tightness at regular intervals and tighten them if necessary.
Have your power tool repaired only by qualified specialists and only with original spare parts. This ensures that the safety of the power tool is maintained.
Allow the device to cool down for 15 minutes after charging or intensive use. Failure to follow this instruction could result in overheating or fire.
Do not open, disassemble, compress, heat above 60 °C or incinerate the device. Do not throw into fire or similar.
Be careful when using the device near flammable or easily meltable materials such as plastic or glass.
Not aim the device at one and the same place for a long time.
Never point the switched-on device at people, animals, plants, flammable objects or liquids.
Do not use the device in an explosive atmosphere.
Be aware that heat can be conducted to combustible materials that are obscured.
Always keep the air vents clean to avoid overheating of the device and risk of fire.
Only use original accessories.
If the device is damaged, stop using the device and have it repaired by a specialist or contact our customer service. Do not disassemble the device or attempt to repair it yourself.

Safety instructions for battery-powered devices
WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a fire, burn and explosion hazard.
Cordless devices do not belong in household waste.
The batteries must be properly disposed of together with the devices.

EC DECLARATION OF CONFORMITY
We, the Westfalia Werkzeugcompany, Werkzeugstraße 1, D-58093 Hagen, declare by our own responsibility that the product
8 V Mini Drilling and Grinder
Article No. 99 20 18
is according to the basic requirements, which are defined in the European Directives and their amendments.

2011/65/EU| Restriction of the Use of certain hazardous Substances in electrical and electronic Equipment (RoHS)
---|---
2014/30/EU| Electromagnetic Compatibility (EMC)
EN IEC 55014-1 :2021, EN IEC 55014-2 :2021,
2006/42/EC| Machinery
EN 60745-1:2009+A11:2010, EN 60745-2-23:2013

The technical documentations are on file at the QA department of the Westfalia Werkzeugcompany.
Hagen, 17th of July, 2023

Thomas Klingbeil,
QA Representative

CUSTOMER SERVICES

Westfalia
Werkzeugstraße 1
D-58093 Hagen
Telefon: (0180) 5 30 31 32
Telefax: (0180) 5 30 31 30
Internet: www.westfalia.de| Westfalia
Moosham 31
A-4943 Geinberg OÖ
Telefon: (07723) 4 27 59 54
Telefax: (07723) 4 27 59 23
Internet: www.westfalia-versand.at| Westfalia
Wydenhof 3a
CH-3422 Kirchberg (BE)
Telefon: (034) 4 13 80 00
Telefax: (034) 4 13 80 01
Internet: www.westfalia-versand.ch
---|---|---

DISPOSAL
Dear Customer
**** Please help avoid waste materials.
If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled. Please do not discharge it in the rubbish bin, but check with your local council for recycling facilities in your area.

Gestaltung urheberrechtlich geschützt
©Westfalia 07/23 ****