RODE WIRELESSGO Compact Wireless Microphone System User Guide

: June 13, 2024
: Rode

Table of Contents

RODE WIRELESSGO Compact Wireless Microphone System
Product Information
Product Usage Instructions
USER GUIDE
OVERVIEW
SET UP
TRANSMITTER – TX
RECEIVER – RX
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RODE WIRELESSGO Compact Wireless Microphone System

Product Information

The Wireless Go is a compact wireless microphone system that operates in the 2.4GHz spectrum. The kit includes a transmitter with an internal microphone and a receiver with a 3.5mm TRS output. The transmitter can use the internal microphone if no external microphone is plugged in, and it has on-board processing optimized for the human voice. The receiver has a standard 3.5mm TRS microphone input and supplies 2.8V plug-in power for compatible microphones. It also has power and link LEDs to indicate battery status and pairing status.

Product Usage Instructions

Power Button

To turn on the unit, press and hold the power button for 3 seconds.
To turn off the unit, press and hold the power button for 3 seconds.
When the device is IN charging mode, a single press of the power button will turn it on.

USER GUIDE

OVERVIEW

The Wireless Go is a compact wireless microphone system that operates in the 2.4GHz spectrum. The kit includes a transmitter with an internal microphone and a receiver with 3.5mm TRS output.

SET UP

Press and hold the power button for 3
seconds to turn on the RX (receiver).
Press and hold the power button for 3
seconds to turn on the TX (transmitter).
The units will already be paired and start transmitting audio, the transmitter will
be using the internal microphone.
Clip on the supplied windshield if required
If desired, plug in a compatible external microphone and the TX will automatically switch the audio input.
Connect the 3.5mm TRS output of the RX to a camera’s microphone input or similar audio device.

TRANSMITTER – TX

Power Button

Press and hold the power button for 3 seconds to turn on the unit Press and hold the power button for 3seconds to turn off the unit Single press to turn on when the device is in charging mode.
Internal Microphone

The transmitter will use the internal microphone if there is not an external microphone plugged in On board processing optimized for the human voice.
Microphone Input

Standard 3.5mm TRS microphone input Supplies 2.8V plug-in power for compatible microphones “Power” and “Link” LED’s.
Power LED

Solid = internal battery is above 20% Slow ﬂ ash = internal battery is below 20%Rapid ﬂ ash = internal battery is below 10% Double ﬂ ash = Charging through USB (solid when 100% charge is reached)
Link LED

Solid = Paired and transmitting to an RX Slow ﬂ ash = Not connected to the RX or out of range Rapid ﬂ ash = in pairing mode (will time out after 3 seconds) Off = TX is in charging mode and to a receiver
USB-C

Standardised USB-C port Used for charging with USB power supplies and is able to connect to a computer for future ﬁ rewire updates The power LED will display charging mode if the unit is plugged into power while off, a quick single press the power button will turn on the TX Wireless Go User Guide.

RECEIVER – RX

Power Button

Press and hold the power button for 3seconds to turn on the unit Press and hold the power button for 3 seconds to turn off the unit Single press to turn on when the device is in charging mode
“dB” Button

Press the “dB” button to cycle through the three audio output levels (0dB, -12dB, -24dB) Set the level according to the requirements of the device receiving the audio. I.e. portable recorder, smartphone, camera, etc. The RX will remember the selection chosen for future use
Link Button

The RX and TX will come pre-paired out of the box If pairing is required Press and hold the button for 3 seconds The signal strength icon on the screen will start ﬂ asking Single press the power button on the TX The TX and RX should pair immediately.
Audio output

Standard 3.5mm TRS output Multi-mono signal.

USB-C

Standardised USB-C port Used for charging with USB power supplies and is able to connect to a computer for future ﬁ rewire updates The screen will display charging mode if the unities plugged into power while off, a quick single press the power button will turn on the RX Wireless Go User Guide V01.

TRS jack output

Pairing button dB Button Screen brightness indicator Transmitter battery status Receiver battery status Microphone input level meter (red = clipping) Pairing status & signal strength indicator Audio output level 3x options.