RODE INTERVIEW PRO Handheld Microphone Adaptor User Guide
- June 1, 2024
- Rode
Table of Contents
INTERVIEW PRO
QUICK START GUIDE
INTERVIEW PRO Handheld Microphone Adaptor
- Unscrew the Interview PRO handle and slide down the cover to reveal its USB-C port
- Connect it to power to charge the internal battery – the power button LED will slowly flash green while charging and turn solid green when fully charged
- Disconnect from power and screw the handle sleeve back into place
- To power the Interview PRO on, press-and-hold the power button (repeat the process to turn it off)
- Enter your wireless receiver into pairing mode (for the Wireless PRO RX, short-press the right navigation button to select the first channel then long-press the right navigation button to enter pairing)
- Short-press the power button on the Interview PRO to enter pairing mode (the power button LED will flash blue)
- When successfully paired, the Interview PRO’s power button LED will turn solid green (this will turn amber when the battery level is low and red when critical)
- Press the ‘REC’ button to start and stop the onboard recording
- Press the ‘Mute’ button to stop the Interview PRO’s signal from being sent to the wireless receiver (on-board recording will continue when ‘Mute’ is enabled)
- View the user guide to learn about timecode capabilities and other advanced settings and features
Download and install RØDE Central to export onboard recordings, manage
settings and run firmware updates.
Be sure to use the included SuperSpeed USB-C cable for best results
rode.com/apps/rode-central
The Interview Pro must not be co-located or operated in conjunction with any
other antenna or transmitter.
The device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to wich the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth in an
uncontrolled environment.
Changes or modifications not expressly approved by RØDE could void the user’s
authority to operate the equipment.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
EU Compliance Statement
Hereby, RØDE Microphones declares that the radio equipment type Interview Pro
is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: http://info.rode.com/interview-pro
Frequency Range: 2.402 – 2.480 GHz
Maximum Output Power: < 10dBm
For details of EU representative go to http://en.rode.com/distributors
USA
**** FCC ID: 2AEAN-INTERVPRO
CANADA
IC: 20091-INTERVPRO
CAN: ICES-3 (B) / NMB-3 (B)
SOUTH KOREA
ID: R-R-R72-INTERVPRO
Company Name: RØDE Microphones
Model: Interview Pro
Country of Origin: Australia
NCC|
---|---
BSMI|
JAPAN|
INDIA|
MEXICO|
POWER
5VDC 1.5A
Note 1： “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.
Note 2： “ ” indicates that the percentage content of the restricted
substance does not exceed the percentage of reference value of presence.
Note 3： The “－” indicates that the restricted substance corresponds to
the exemption.
Regulatory information such as identification numbers are displayed on internal housing by unscrewing the handle.
SCAN FOR MORE INFO
https://rode.com/user-guides
/interview-pro
View the user guide to learn more
To prevent possible hearing damage, do not listen at high volume levels for long periods.
RØDE Microphones:
107 Carnarvon St, Silverwater NSW 2128, Australia
Authorised UK Representative:
RØDE UK, Unit A, 23-25 Sunbeam Rd, London NW10 6JP, United Kingdom
Authorised EU Representative:
RØDE EU, Neukirchner Str. 18, 65510 Hünstetten, Germany
rode.com
0927-0837-02-04
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>