RODE STREAMER X Audio Interface and Video Capture Card User Guide

: June 1, 2024
: Rode

Table of Contents

STREAMER X Audio Interface and Video Capture Card
RADIATION EXPOSURE STATEMENT
EU COMPLIANCE STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

QUICK START GUIDE

STREAMER X Audio Interface and Video Capture Card

Either power the Streamer X from your computer using the included SuperSpeed USB-C cable connected to USB 1, or use the included power supply connected to the Streamer X’s dedicated power input.
Connect your HDMI source device (like your console or camera) into the HDMI IN port and connect your monitor or TV to HDMI THRU.
Connect your XLR, headset, or wireless microphone and select your input type by pressing the left encoder knob. Adjust the input gain by turning this encoder.
Connect headphones (if you’re not using a headset) and adjust your monitoring level with the right encoder. You can press this encoder to mute your headphones.
Download RØDE Central to configure your Streamer X and access its processing, effects, and SMART pad customization. See below for more information.
View the online user guide for more information on how to master your Streamer X.

Download RØDE Central to configure your Streamer X and access its processing, effects, and SMART pad customization. See below for more information rode.com/apps/rode-central

NORTH AMERICA
The Streamer X must not be co-located or operated in conjunction with any other antenna or transmitter.
The device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth in an uncontrolled environment.
Changes or modifications not expressly approved by RØDE could void the user’s authority to operate the equipment.
CAN ICES-003 (B) / NMB-003 (B)
This Class B digital apparatus complies with
Canadian ICES-003.

RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
Radio Frequency Exposure Statement for Canada
The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions. The minimum separation distance is 20cm.

Company Name: RODE LLC
Address: 2745 Raymond Ave, Signal Hill CA
90755, USA
Telephone Number: +1 562 364 7400

EU COMPLIANCE STATEMENT

Hereby, RØDE Microphones declares that the radio equipment type Streamer X is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://www.rode.com/streamer-x
Frequency Range: 2.402 – 2.480 GHz
Maximum Output Power: < 10dBm
For details of EU representative go to http://en.rode.com/distributors

Caution:
The Streamer X has been designed to be used with the provided power supply, as use the provided power supply only. Stop using the power supply unit and any cables if:

There is any damage to the charging port, power connector or power cord.
The power supply unit is exposed to excessive moisture, or liquids is spilled into the power supply unit.
The power supply unit enclosure is broken.

POWER SUPPLY UNIT SPECIFICATIONS:
Model Name: YDS-PD030A
Frequency: 50-60 Hz
Line Voltage: 100-240 Vac
Output Ratings: 20Vdc 1.5A; 15Vdc 2.0A; 12Vdc 2.5A; 9Vdc 3A; 5Vdc 3A

RODE STREAMER X Audio Interface and Video Capture Card - Fig
1