Eurom 400 Alutherm XS Wi-Fi User Manual

Eurom 400 Alutherm XS Wi-Fi User Manual

This product is only suitable for well insulated spaces or occasional use.

Mandatory warnings

Please read and understand these safety instructions. Incorrect use can cause injury and will void EUROM’s warranty.

WARNING
In order to avoid overheating, do not cover the heater

CAUTION
Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

WARNING

• Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
• To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air outlet.
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Heater must not be located immediately below a socket-outlet.
• If the supply cord is damaged, it must be replaced by manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Heater is to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• Do not use this heater if it has been dropped.
• Do not use if there are visible signs of damage to the heater.

When using the Alutherm heater freestanding with the pedestals mounted: Use this heater on a horizontal and stable surface.

The device is equipped with an overheating protection, which switches it off automatically in case of internal overheating. Switch the device off, unplug the power plug, remove the source of overheating, let it cool down and use as normal. Do not use the device if the source of overheating cannot be traced or if the problem persists, but always contact your supplier.

The device is fitted with a tipping safeguard, which ensures it automatically shuts off if it tips over. When the device is returned to its upright position, it will resume functioning normally. Before reusing the device, switch it off, unplug it and check it for damage. Do not use the device if it is damaged or malfunctioning, but always contact your supplier.

General safety instructions

WARNING

• Prevent splashing water on or in the device.
• Do not immerse any part of the device in water or other liquids.
• Never insert fingers or other objects into the openings of the device.
• Do not expose the device to strong vibrations or mechanical stress.

WARNING
The device becomes very hot during use. Do not touch the device during use or within five minutes after use.

CAUTION
Do not cover the device during usage or after use while the device is still hot. To reduce the risk of fire, keep textiles, curtains, tent canvasses and other flammable material at a minimum distance of 1 meter from the device. Safety during operation

WARNING
Do not use the device:

• outdoors or in a small space;
• if any parts are dirty or wet;
• near large objects, like behind a door, under a shelf or cupboard;
• near a water source, like a bath, shower, swimming pool or open window;
• near or in a dusty and dirty environment, like a construction site;
• near flammable materials, liquids or fumes, like a shed, stable or green house;
• near other heat sources and open fire;
• immediately below a socket outlet;
• with an appliance that automatically switches the device on, such as a timer, dimmer or any other device.

If the device, the electric cable or plug shows damage or is malfunctioning, immediately take the appliance out of use and disconnect the power supply.

Warranty
EUROM offers a 5-year warranty on this device from the date of purchase. The warranty does not cover wear and tear from normal use. The warranty expires if a defect is the result of unintentional or careless use of the device. The manufacturer, importer and supplier are not liable for incorrect connections. Introduction

Thank you for choosing this EUROM device. You have purchased a quality device that you will enjoy for many years. Using this device with respect and care will reduce the risk of personal injury or material damage.

CAUTION
It is important to read and understand this instruction manual before assembling, installing and using the device.

This manual describes the correct and safe use of this device. Keep this manual for future reference. The manual is an essential part of the device and must be given to the new owner upon resale or exchange. This manual has been compiled with the utmost care. Nevertheless, we reserve the right to improve and adjust this manual at any time. The images used may differ.

The following symbols and terms are used in this manual to alert the reader on safety issues and important information:

WARNING
Indicates a hazardous situation which, if the safety instructions are not followed, can lead to injuries to the operator or bystanders, light and/or moderate damage to the product or to the environment.

CAUTION
Indicates a hazardous situation which, if the safety instructions are not followed, can lead to light and/or moderate damage to the product or to the environment.

Identification

Specifications

Hereby, Euromac b.v. declares this product is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: www.eurom.nl/declaration-of- conformity.

• Wi-Fi and Bluetooth Frequency Band: 2.400 ~ 2.4835GHz
• Maximum radio-frequency power transmitted in this frequency band(s):
  • Wi-Fi: 17,5dBm
  • Bluetooth: 6,5dBm

Description
The Alutherm Wi-Fi is an easy-to-use electric heater for indoor use, see (Figure 3). The device can be programmed on a day and a week timer. The Alutherm Wi-Fi can be used with the Eurom Smart App.

1. ON/OFF switch
2. Control panel and LED display
3. Remote control
4. Power plug
5. Air inlet safety grill
6. Pedestals (optional)
7. Heat outlet safety grill

Control panel

1. ON/OFF button
2. LED display
3. SET button
4. WEEK button
5. Minus button
6. Remote control receiver
7. Plus button
8. MOD button

LED display

The LED display will go dark if no adjustments are made for 2 minutes. The LED display will light up again when you press a button.

Status indication (Figure 5, pos. 1):

• The 3 suns indicate whether the heater is set to low, medium or high capacity.*
• The Wi-Fi symbol indicates if there is a Wi-Fi connection.
• The “P” indicates that the program function is active.
• The “M” indicates that the manual function is active

*Does not apply to 400XS Wi-Fi, this model only has 1 heating level.

Temperature indication (Figure 5, pos. 2):

• SET indicates that a day or time can be set.
• ON indicates that the heater is switched on.
• OFF indicates that the heater has been switched off by the stand-by button or the tipping safeguard.
• Temperature shown in degree Celsius.

Time indication (Figure 5, pos. 3):

• Time shown in 24-hours format.

Day indication (Figure 5, pos. 4):

• Number corresponds with the day of the week: 1 = Monday, 2 = Tuesday, and so on.

Wi-Fi indication (Figure 5, pos. 5):

• The “G” indicates that the device is connected to the Wi-Fi thermostat.

Remote control

1. ON/OFF button
2. SET button
3. Frost protection button
4. Minus button
5. WEEK button
6. Plus button
7. Heat capacity button
8. ECO button
9. MODE button

*Batteries not included

Transport and storage

• Clean the device before storing it.
• Transport the device upright.
• Store the device upright in its original packaging in a cool, dry and dust-free area.

Assembly

WARNING
Never place the device on surfaces such as beds or deep-pile carpet as openings could be blocked.

WARNING
Plastic bags can be dangerous. To avoid danger of suffocation, keep this bag away from babies and children.

The device is packed in one box. Remove all packaging materials and check that the device is not damaged. Do not use the heater if it is damaged, but always contact your supplier. Keep the packaging for safe storage and transport. The device can be assembled in two ways; mounted on pedestals or mounted on a wall.

Mounting on pedestals

1. Lay the device down on a soft, steady surface (Figure 7, pos. 4).
2. Place the pedestals (Figure 7, pos. 3) on both sides of the main body (Figure 7, pos. 5).
3. Screw and tighten each pedestal with two small screws (Figure 7, pos. 1) using a Phillips screwdriver (Figure 7, pos. 2).
4. Place the device on a horizontal, solid and non-flammable surface.
5. Place the device with a minimum clearance distance (Figure 8) of:
   • 150 cm on the top side;
   • 30 cm on the sides;
   • 30 cm on the back side;
   • 50 cm on the front side.
6. Do not place the device immediately below a power outlet.
   

Wall mounting

WARNING
The wall used for mounting must be made from non-flammable material and should be able to withstand a minimum temperature of 200 °C.

CAUTION
Make sure to use suitable fastening materials, depending on the surface. Never block the space between the device and the wall.

1. Place the device on a vertical and solid surface. Use a spirit level when placing the device (Figure 9, pos. 1).

2. Place the device with a minimum distance (Figure 9) of:

   • 150 cm from the ceiling;
   • 30 cm from the side walls;
   • 30 cm from the floor;
   • 50 cm clearance on the front side.

3. Do not mount the device:

   • immediately below a socket outlet;
   • on a ceiling or roof.
     

4. Drill two holes at least 610 mm above the floor for the brackets. The distance between the holes is approximately (Figure 10, pos. A)*:

   • Alutherm 400XS: 195 mm;
   • Alutherm 800XS: 255 mm;
   • Alutherm 1200XS: 400 mm.

5. Place wall plugs (Figure 10, pos. 2).

6. Screw and tighten a left and a right bracket (Figure 10, pos. 3) to the wall with a large screw (Figure 10, pos. 4) using a Phillips screwdriver (Figure 10, pos. 1).
   
   CAUTION
   Be aware that these are the holes for the wall bracket and not the slots in the heater.

7. Lay the device down on a soft, steady surface (Figure 11, pos. 4).

8. Screw and tighten two brackets (Figure 11, pos. 1) on both sides of the main body (Figure 11, pos. 5) with a small screw (Figure 11, pos. 2) using a Phillips screwdriver (Figure 11, pos. 3).
   

9. Place the bracket holes (Figure 12, pos. 4) over the wall brackets (Figure 12, pos. 1).

10. Let the device (Figure 12, pos. 2) drop into the openings of the wall brackets (Figure 12, pos. 1).

11. Use the device brackets (Figure 12, pos. 3) to mark the bottom hole position on the wall.

12. Remove the device from the wall brackets (Figure 12, pos. 1).
    

13. Drill two holes at the marked positions and place the wall plugs.

14. Place the device (Figure 13, pos. 2) back on the wall brackets (Figure 13, pos. 1).

15. Screw and tighten the device brackets (Figure 13, pos. 4) with a large screw (Figure 13, pos. 3) to the wall (Figure 13, pos. 3) using a Phillips screwdriver (Figure 13, pos. 2).
    

Installation

WARNING
Do not put the power plug into the wall socket before the device is correctly mounted or stands in the right place.

Do not use an extension cable; this can cause overheating and fire. If using an extension cable is unavoidable, make sure it is undamaged and earthed. Use an extension cable with a minimum power of 1000 Watt (400XS), 1500 Watt (800XS) or 2000 Watt (1200XS). Always unwind the extension cable completely to prevent overheating.

CAUTION
Make sure that the main voltage is the same as indicated on the identification label of the device. All electrical connections must stay dry under all circumstances.

1. Make sure the device is correctly assembled.
2. Make sure the ON/OFF switch is in the OFF position (Figure 14, pos. 1).
3. Place the power plug (Figure 14, pos. 2) into an earthed wall socket that is easily accessible. Use an earthed wall socket with a minimum power of 2500 Watt.
   

Remote control

1. Remove the battery cover (Figure 15, pos. 1).
2. Insert two AAA 1.5V batteries (Figure 15, pos. 2) in the battery compartment. Make sure to insert the batteries correctly.
3. Replace the cover.

Operation

WARNING
Before every use, make sure that:

• you operate the device with dry hands;
• the device is clean and dry;
• the device is not damaged;
• the device is not covered or blocked;
• the device is securely installed.

CAUTION
When the device is turned on or off, it may emit a sound. This is caused by material expanding and shrinking during heating and cooling down.

CAUTION
The day and time settings will be lost if the device is switched off by using the ON/OFF switch or by unplugging it.

1. Set the ON/OFF switch to the ON position (Figure 16, pos. 1).
2. The display (Figure 16, pos. 2) will show OFF.
3. Press the ON/OFF button.
4. Press and hold the SET button until SET appears on the screen.
5. Use the plus and minus buttons to select the correct day and confirm with the SET button.
6. Use the plus and minus buttons to set the correct time:
   • Hours, confirm with the SET button;
   • Minutes, confirm with the SET button.
7. Press the MOD button to choose the desired function: manual or program.
   

Manual function
Set the capacity at which the heater will work using the plus and minus buttons. The 3 suns indicate whether the heater is set to low, medium or high capacity*.

*Does not apply to Alutherm 400XS, this model only has 1 heating level.

Program function

Set the desired temperature for the device using the plus and minus buttons. The device automatically chooses the correct heating capacity to achieve and maintain the desired temperature;

• 10 minutes after the desired temperature has been reached the device will change from high capacity to medium capacity;
• every 5 minutes the device will check the ambient temperature and adjust the heating capacity:
  • if the ambient temperature is more than 1 degree below the desired temperature, the device will increase capacity;
  • if the ambient temperature is within 1 degree below and 1 degree above the desired temperature, the device will maintain current capacity
  • if the ambient temperature is more than 1 degrees above the desired temperature, the device will decrease capacity;
  • if the ambient temperature is more than 2 degrees above the desired temperature, the device will stop heating after 5 minutes.

In most cases the device will heat up the room to a slightly higher temperature than the desired one. To save energy, it is recommended not to set the desired temperature too high and adjust accordingly.

Weekly timer setting
The week timer can be set via the remote control or the control panel, but it is easier to use the Eurom Smart App

1. Make sure the device is set to program function
2. Press and hold the WEEK button until ‘01’ or ‘][‘ starts to blink on the screen.
3. Use the plus and minus buttons to choose the desired setting:
   • 01 – one-off setting (must fall in the current week).
   • ][ – every week setting.
4. Confirm with the SET button; ON appears blinking on the screen.
5. Use the plus and minus buttons to choose the desired anticipation setting:
   • ON – the heater will anticipate the temperature 20 minutes before it is set. If it needs to be heated, the heater will heat with high capacity in order to heat the room to the desired temperature by the activation time*.
   • OFF – the heater will not anticipate the temperature and will turn on at the set time*.
6. Confirm with the SET button, 01 SET ON appears on the screen.
7. Use the plus and minus buttons to select:
   • the desired day (from 1 (Monday) to 7 (Sunday), confirm with the SET button;
   • the desired temperature, confirm with the SET button;
   • the desired hours, confirm with the SET button;
   • the desired minutes, confirm with the SET button.
8. 01 SET OFF will appear on the screen; repeat step 7 to indicate the deactivation time.
9. 02 appears on the screen, there are two options:
   • Set the next activation and deactivation times, repeat step 7 and 8 for every desired time. Make sure the timer settings do not contradict each other: maximum 28 per week, maximum 4 per day.
   • If you are done setting the activation and deactivation times, wait until the screen returns to standard settings.
10.  The screen will show P and the device will automatically switch on and off at the set times.

*Does not apply to the 400XS.

View weekly timer setting

Press the WEEK button repeatedly. You will see the following timer settings, one after the other:

• one-off or repeated;
• anticipation on or off;
• temperature setting;
• timer on-time;
• imer off-time;
• next timer setting.

All 28 timer settings are shown, including the settings that have not been configured.

Turning off weekly timer setting

Press and hold the WEEK button until ‘01’ or ‘][‘ appears on the screen.

Press and hold the MOD button until TIME disappears from the screen, which indicates that the data will be retained but will not be active. By pressing the MOD button again until TIME appears, you will reactivate the timer.

Deletingweekly timer setting
Timer settings can only be deleted with the buttons on the control panel.

1. Press and hold the WEEK button until ‘01’ or ‘][‘ appears on the screen.
2. Go past ‘01- ][‘ and on/off first by pressing SET briefly.
3. When the number of the timer setting that you want to change appears, press the SET
button for a little longer. You will hear a short beep and the selected setting will have
been deleted.
4. If you want to delete all timer settings, press and hold the WEEK button until ‘01’ or ‘][‘ appears on the screen. Press and hold the MOD and SET buttons at the same time, until you hear a beep. The screen will show 88:88, indicating that all settings have been deleted.

Frost protection mode
The remote control has a frost protection button, which can be pressed to create and maintain a room temperature of 5°C.

1. Press the frost protection button to activate; FP appears on the screen.
2. Press the frost protection button to deactivate.

If the heater is working in frost protection mode and a timer setting becomes active, the device will start to work according to the timer setting. When the timer setting ends and the device goes off, the device will not return to the frost protection mode.

ECO mode
The remote control has an ECO button for an energy-efficient mode; the device maintains the room temperature at 16°C.

1. Press the ECO button to activate; EC appears on the screen.
2. Press the ECO button to deactivate.

If the heater is working in ECO mode and a timer setting becomes active, the device will start to work according to the timer setting. When the timer setting ends and the device goes off, the device will not return to the ECO mode.

Eurom Smart App

CAUTION
Do not use the weekly timer created with the device at the same time as the weekly timer created with the Eurom Smart App. Timer settings created by the Eurom Smart App are not visible on the device display. Timer settings created on the device are not visible in the Eurom Smart App.

The device can be operated using an app on a smartphone or tablet. The Eurom Smart App can be used:

• to switch the device on and off;
• to regulate the temperature and capacity;
• to activate the frost protection mode.

The app can also be used to set twenty on and off timer settings daily, on the weekly timer.

1. Open the Eurom Smart App manual with the QR code (Figure 17) or go to www.eurom.nl/nl/manuals.
   

2. Complete the steps in the Eurom Smart App manual.

   • When the device is connected with Wi-Fi, the Wi-Fi symbol appears on the screen.
   • If the Wi-Fi symbol is blinking there is no connection.

Smart Timer

1. Create a schedule with days and times in the Eurom Smart App. Timer settings set in the app:
   • will be stored on the device;
   • will not be visible on the device;
   • will remain available if Wi-Fi disconnects;
   • will remain available if the device is switched off or unplugged;
   • can only be removed in the app.
2. Check the data in the app regularly.

ResetWi-Fi connection

1. Press and hold the MOD button. Existing connections will be deleted, the Wi-Fi symbol will start blinking and a new connection will be made.

Switch offWi-Fi connection

1. Press and hold the OFF button until a long beep sounds. The Wi-Fi is switched off and the Wi-Fi symbol will disappear from the screen.
2. Press and hold the OFF button until a short beep sounds. The Wi-Fi is switched on and the Wi-Fi symbol will appear on the screen.

Wi-Fi thermostat ready (optional)
This device can be connected with the optional Wi-Fi thermostat. The temperature is measured at the Wi-Fi thermostat instead of the device. This ensures an optimized comfort level. The device will keep heating until the set temperature on the Wi-Fi thermostat is reached.

It is possible to connect multiple devices to a single Wi-Fi thermostat. All the connected devices will switch on and off simultaneously.

To use the Wi-Fi thermostat:

1. Place the Wi-Fi thermostat in any power socket.
2. Download the Eurom Smart App on a (mobile) device.
3. Open the Eurom Smart App.
4. Add the Wi-Fi thermostat and other devices to the Eurom Smart App.
5. Go to the device(s) and press the Pairing Button to pair the device(s) to the Wi-Fi thermostat.

The device is connected to the Wi-Fi Thermostat. The G-sign illuminates in the Eurom Smart App and on the device. Now you can enjoy the optimized comfort level of permanent electric heating.

After operation

CAUTION
Do not use the power cable to unplug or carry the device. Do not wind the power cable too tightly or in sharp corners. Do not wrap the power cable around the device.

1. Make sure the ON/OFF switch is in the OFF position (Figure 16, pos. 1).
2. Disconnect the power plug from the power outlet (Figure 16).
3. Let the device cool down before touching it.
4. Wind the power cable.
5. Remove the batteries from the remote control (Figure 17).

Maintenance

WARNING
Do not perform any repairs or modifications to this device.

Maintenance and repairs must be carried out by a EUROM authorized professional. If the electric cable and/or electric plug are damaged, they should be replaced by the manufacturer, their service employee or persons with similar qualifications to prevent risks

Cleaning

WARNING
This device becomes very hot. Make sure the device is turned off, unplugged and completely cooled down before cleaning it.

CAUTION
Do not use:

• scouring pads;
• hard brushes;
• flammable, aggressive or chemical cleaning products.

Prevent water from entering the device. Do not immerse any part of the device in water or other liquids.

It is recommended to clean the device after each use and prior to storage.

1. Carefully vacuum the openings to remove dust and dirt.
2. Wipe the device with a damp, clean, soft, lint-free cloth or a soft brush.
3. Let the device dry completely prior to use and storage.

Disposal

Correct Disposal of this product.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Information requirement for the electric local space heaters

Model identifier(s): Alutherm 400XS Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage localspace heaters only (select one)
Nominal heatoutput| Pnom| 0,4| kW| manual heat charge control,with integrated thermostat| Not applicable
Minimum heat output (indicative)| Pmin| 0,4| kW| manual heat charge control with room and/or outdoortemperature feedback| Not applicable
Maximum continuous heatoutput| Pmax,c| 0,4| kW| electronic heat charge control with room and/or outdoortemperature feedback| Not applicable
Auxiliary electricity consumption| fan assisted heat output| Not applicable
At nominal heatoutput| elmax| 0,000| kW| Type of heat output/room temperaturecontrol (select one)
At minimum heatoutput| elmin| 0,000| kW| single stage heat output andno room temperature control| No
In standby mode| elSB| 0,000432wifi turn off, 0,000865wifiturn on| kW| Two or more manual stages, no room temperature control| No
| | | | with mechanic thermostatroom temperature control| No
| | | | with electronic roomtemperature control| No
| | | | electronic room temperaturecontrol plus day timer| No
| | | | electronic room temperaturecontrol plus week timer| Yes
| | | | Other control options (multiple selectionspossible)
| | | | room temperature control,with presence detection| No
| | | | room temperature control,with open window detection| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands
Information requirement for the electric local space heaters

Model identifier(s): Alutherm 800XS Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage localspace heaters only (select one)
Nominal heatoutput| Pnom| 0,8| kW| manual heat charge control,with integrated thermostat| Not applicable
Minimum heat output (indicative)| Pmin| 0,3| kW| manual heat charge control with room and/or outdoortemperature feedback| Not applicable
Maximum continuous heatoutput| Pmax,c| 0,8| kW| electronic heat charge control with room and/or outdoortemperature feedback| Not applicable
Auxiliary electricity consumption| fan assisted heat output| Not applicable
At nominal heatoutput| elmax| 0,000| kW| Type of heat output/room temperature control(select one)
At minimum heatoutput| elmin| 0,000| kW| single stage heat output andno room temperature control| No
In standby mode| elSB| 0,000432wifi turn off, 0,000865wifiturn on| kW| Two or more manual stages, no room temperature control| No
| | | | with mechanic thermostatroom temperature control| No
| | | | with electronic roomtemperature control| No
| | | | electronic room temperaturecontrol plus day timer| No
| | | | electronic room temperaturecontrol plus week timer| Yes
| | | | Other control options (multiple selectionspossible)
| | | | room temperature control,with presence detection| No
| | | | room temperature control,with open window detection| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands
Information requirement for the electric local space heaters

Model identifier(s): Alutherm 1200XS Wi-Fi
Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage localspace heaters only (select one)
Nominal heatoutput| Pnom| 1,2| kW| manual heat charge control,with integrated thermostat| Not applicable
Minimum heat output (indicative)| Pmin| 0,5| kW| manual heat charge control with room and/or outdoortemperature feedback| Not applicable
Maximum continuous heatoutput| Pmax,c| 1,2| kW| electronic heat charge control with room and/or outdoortemperature feedback| Not applicable
Auxiliary electricity consumption| fan assisted heat output| Not applicable
At nominal heatoutput| elmax| 0,000| kW| Type of heat output/room temperature control(select one)
At minimum heatoutput| elmin| 0,000| kW| single stage heat output andno room temperature control| No
In standby mode| elSB| 0,000432wifi turn off, 0,000865wifiturn on| kW| Two or more manual stages, no room temperature control| No
| | | | with mechanic thermostatroom temperature control| No
| | | | with electronic roomtemperature control| No
| | | | electronic room temperaturecontrol plus day timer| No
| | | | electronic room temperaturecontrol plus week timer| Yes
| | | | Other control options (multiple selectionspossible)
| | | | room temperature control,with presence detection| No
| | | | room temperature control,with open window detection| No
| | | | with distance control option| Yes
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Eurom – Kokosstraat 20 – 8281 JC – Genemuiden – The Netherlands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>