StarTech com QUAD-M2-PCIE-CARD-B PCI Express x16 to Quad M.2 PCIe SSD Adapter with Bifurcation User Guide

: June 4, 2024
: StarTech com

Table of Contents

StarTech com QUAD-M2-PCIE-CARD-B PCI Express x16 to Quad M.2 PCIe SSD
Product ID
Product Information
Package Contents
Requirements
Installation
- Install the M.2 Storage Drives
- Install the Card
Regulatory Compliance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

StarTech-com-QUAD-M2-PCIE-CARD-B-PCI-Express x16-to-Quad-M.2-PCIe-SSD-
Adapter-with-BifurcationLOGO

StarTech com QUAD-M2-PCIE-CARD-B PCI Express x16 to Quad M.2 PCIe SSD

Adapter with Bifurcation

StarTech-com-QUAD-M2-PCIE-CARD-B-PCI-Express x16-to-Quad-M.2-PCIe-SSD-
Adapter-with-Bifurcation-PRODUCT-IMAGE

Product ID

StarTech-com-QUAD-M2-PCIE-CARD-B-PCI-Express x16-to-Quad-M.2-PCIe-SSD-
Adapter-with-Bifurcation-01

Component	Function
1	LED Jumper Pins

Adapter Card to show Drive** activity

2

| Standoffs (x 4), Standoff Installation Screws (x 4), and Drive Mounting Screws (x 4)| • Secure M.2 Storage Devices to the PCIe to M.2 Adapter Card

• Compatible PCIe M.2 SSDs (NVMe and AHCI): 2242, 2260, 2280, and 22110 drives

3| M.2 Connectors| • Connect M Keyed M.2 Storage Devices to the

PCIe to M.2 Adapter Card

4| PCIe x16 Connector| • Connect the PCIe to M.2 Adapter Card to the

PCIe Slot in a Computer

Product Information

For the latest manuals, product information, technical specifications, and declarations of
conformance, please visit: www.StarTech.com/QUAD-M2-PCIE- CARD-B

Package Contents

PCIe to M.2 Adapter Card x 1
Quick-Start Guide x 1

Requirements

Computer x 1
PCIe x16 Slot with Bifurcation Support
Phillips Head Screwdriver x 1
PCI Express M.2 SSD x 4
Pliers x 1

Installation

Warning : PCIe Cards can be damaged by static electricity. Ensure that the Installer is properly grounded before they open the Computer Case or touch the PCIe to M.2 Adapter Card. The Installer should wear an Anti-Static Strap when installing any computer component. If an Anti-Static Strap is not available, discharge any built-up static electricity by touching a large Grounded Metal Surface for several seconds. Only handle the PCIe to M.2 Adapter Card by its edges and do not touch the gold connectors.
Note: Consult the documentation that came with the Computer/Motherboard for details regarding how to enable and configure PCIe Bifurcation.

Install the M.2 Storage Drives

Place the Drive next to the Adapter and note the Drive Installation Holes that match the length of the Drive. If the Standoffs and Installation Screws are already installed in the correct position, proceed to step 5.
On the front of the M.2 Adapter Card, use Pliers to hold the Standoff in place while using a Phillips Head Screwdriver to remove the Screw, located on the back of the Adapter.
Use the Phillips Head Screwdriver to remove the Screw on the front of the M.2 Adapter Card.
Remove the Standoff.
Repeat steps 2 – 3 to remove the remaining Standoffs and Standoff Installation Screws as needed.
Install the Standoff in the Drive Installation Hole that matches the length of the Drive.
Gently slide the M.2 Drive Connector into the corresponding M.2 Connector, located on the M.2 Adapter Card, and press the Drive down toward the adapter until the Drive is properly seated
Note : The M.2 Connector on the Drive is M Keyed so that it only fits M Keyed M.2 Storage Devices
Replace the Standoff Installation Screw, removed in step 2, and tighten using a Philips Head Screwdriver.
Insert the Drive Mounting Screw through the Drive Slot and into the Standoff and use the Phillips Head Screwdriver to tighten the Drive Mounting Screw, securing the Drive in place.
Repeat Steps 1 – 8 to install the remaining Drives.

Install the Card

Turn off the Computer and disconnect the Power Cable and any Peripheral Devices that are connected (e.g. printers, external hard drives, etc.).
Remove the Cover from the Computer Case.
Note : Consult the documentation that came with the Computer for details about how to do this safely.
Locate an open PCIe x16 Slot and remove the corresponding Metal Cover Plate from the rear of the Computer Case. In most instances, the Metal Cover Plate is attached to the rear of the Computer Case with a single Phillips Head Screw. Save this Phillips Head Screw for the next step.
Gently insert the PCIe to M.2 Adapter Card into the open PCIe x16 Slot and fasten the Bracket to the rear of the Computer Case, using the Phillips Head Screw from step 4.
Replace the Cover from the Computer that was removed in step 2.
Reconnect all of the Peripheral Devices that were disconnected in step 1.
Reconnect the Power Cable to the rear of the Computer.

Regulatory Compliance

FCC – Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.
NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Warranty Information

This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Use of Trademarks, Registered Trademarks, and other Protected Names and

Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.