WATLOW FMHA 0600-0096-0000 High Density Input/Output Modules User Guide

: June 13, 2024
: WATLOW

Table of Contents

WATLOW FMHA 0600-0096-0000 High Density Input/Output Modules
Safety Information
Available F4T/D4T Literature and Resources
Installation and Wiring
Input Connections
Warranty
Technical Assistance
Specifications
How to Reach Us
Read User Manual Online (PDF format)
Download This Manual (PDF format)
2208, Hyundia KIC Building B, 70 Doosan-ro

WATLOW FMHA 0600-0096-0000 High Density Input/Output Modules

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-PRODUCT-IMG

Safety Information

We use caution symbols where needed within this document to draw your attention to important operational and safety information.
A “CAUTION” safety alert appears with information that is important for protecting your equipment and performance. Be especially careful to read and follow all cautions that apply to your application.
A “WARNING” safety alert appears with information that is important for protecting you, others and equipment from damage. Pay very close attention to all warnings that apply to your application.
The electrical hazard symbol, (a lightning bolt in a triangle) precedes an electric shock hazard CAUTION or WARNING safety statement. Further explanations follow:

Symbol	Explanation

| CAUTION – Warning or Hazard that needs fur- ther explanation than label on unit can provide. Consult QSG for further information.

Available F4T/D4T Literature and Resources

All of the user documents listed below can be found on the Watlow website: http://www.watlow.com. The Watlow Support Tools DVD can be acquired by contacting Watlow customer service (507-494-5300).

Document Title and Part Number	Description

F4T Installation and Troubleshooting User Guide, part number: 0600-0092-

0000

| Provides detailed specifications and information regarding mounting the base, flex module wiring and troubleshooting.

F4T Setup and Operations User Guide, part number: 0600-0093-0000

| Explains how to configure and operate the device for an application using Composer software as well as the user interface (touch screen). Includes detailed descriptions of all device features and parameter settings.
D4T Installation and Troubleshooting User Guide, part number: 0600-0107-

0000

| Provides detailed specifications and information regarding mounting the base, flex module wiring and troubleshooting.

D4T Setup and Operations User Guide, part number: 0600-106-0000

| Explains how to configure the datalogger for an application using the user interface and Composer software. Includes detailed descriptions of all data logger features and parameter settings.

Installation and Wiring

To install the flex module:

Note the part number to determine the number and type of inputs oroutputs available to be connected in step 7.
Turn off device power.
Select a compatible base slot for the module. See the Flex Module-Slot Dependencies table below. If replacing a module, remove the oldmodule.
Affix corresponding slot number labels (provided) to the module and tothe removable screw terminal block.
With the component side of the module facing right (viewing the F4T/D4Tfrom the rear) insert the module into the slot until it latches.
Remove the screw terminal block from the module.
Wire field devices to the appropriate terminals. Wiring details for each input and output are provided in the following sections.
Reconnect the wired screw terminal block to the module. Be sure to reconnect the terminal block to the correct module.
Restore power to the F4T/D4T.

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-4

Note
If the flex module is a replacement with the same part number and slot position, the F4T/D4T uses it immediately when powered up. Otherwise, use Composer software to configure the F4T/D4T to expect and use the module.

Module Characteristics Description and Identification

Many of the modules appear to look alike at first glance, therefore, it is always recommended that the module part number be verified prior to plugging it into any of the available slots in a base. Each module is identified with a part number located on the back side of the assembly next to the screw terminal block, as displayed in the graphic to the right.

Wiring
Prior to wiring any of the I/O modules described in this document, it is recommended that the warnings and notes listed below be reviewed.
CAUTION
To prevent damage to the F4T/D4T, do not connect wires to unused terminals.

Note
Maintain electrical isolation between the analog input, digital input-outputs, switched dc/open collector outputs and process outputs to prevent ground loops.
Note
Modules IP10 when properly installed in base enclosure with slot caps in empty slots.
CAUTION: Quencharc Note:
Switching pilot duty inductive loads (relay coils, solenoids, etc.) with the mechanical relay, solid-state relay or open collector output options requires use of an R.C. suppressor for AC load or a diode for a DC load.

Note
Wire size and torque for screw terminations:

0.0507 to 3.30 mm2 (30 to 12 AWG) single-wire termination or two 1.31 mm2 (16 AWG)
0.57 Nm (5.0 lb.-in.) torque

Input Connections

Thermocouple

FMHA – [R] A A A – A _

Grounded or ungrounded sensors, greater than 20MΩ input impedance, 2kΩ source resistance max
3μA open-sensor detection
Thermocouples are polarity sensitive. The negative lead (usually red) must be connected to S terminal
To reduce errors, the extension wire for thermocouples must be of the same alloy as the thermocouple

RTD

FMHA – [R] A A A – A _

Platinum, 100 and 1kΩ @ 32°F (0°C) calibration to DIN curve (0.00385 Ω/Ω/°C)
RTD excitation current of 0.09mA typical. Each ohm of lead resistance may affect the reading by 2.55°C for a 100Ω platinum sensor or 0.25°C for a 1kΩ sensor (see table to right)

AWG	Ohms/ 1000ft
14	2.575
16	4.094
18	6.510
20	10.35
22	16.46
24	26.17
26	41.62
28	66.17

Process

FMHA – [R] A A A – A

0 to 20mA @ 100Ω input impedance
0 to 10V (dc) @ 20kΩ input impedance
0 to 50mV (dc) @ 20MΩ input impedance
Scalable

Potentiometer

FM [M, L] A – [C, L, Y, R] A – A

Potentiometer: 0 to 1.2kΩ

Thermistor

FMHA – [P] A A A – A _

20MΩ input impedance
0 to 40kΩ, 0 to 20kΩ, 0 to 10kΩ, 0 to 5kΩ
2.252kΩ and 10kΩ base at 77°F (25°C)
User-selectable curves for Alpha Technics, Beta THERM and YSI
User-scaling support for Steinhart-Hart coefficients

Thermistor Curve Setting| Base R @ 25 ºC| Alpha Technics| Beta Therm| YSI
---|---|---|---|---
Curve A| 2.252k| Curve A| 2.2k3A| 004
Curve B| 10k| Curve A| 10k3A| 016
Curve C| 10k| Curve C| 10k4A| 006

Custom

| Use Steinhart-Hart equation coefficients (A, B and

C) from thermistor manufacturer corresponding to the terms of the Steinhart- Hart equation:

1 / T = A + B ln (R) + C (ln(R))3

Six Digital Inputs

Voltage
- Max. input 36V at 3mA
- Input inactive when ≤ 2V
- Input active when ≥ 3V at 0.25mA
Dry Contact
- Input inactive when ≥ 500Ω
- Input active when ≤ 100Ω
- Max. short circuit 13mA

FMHA – [C] A A A – A _

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-13

Six Digital Outputs

Open Collector

Maximum switched open collector voltage is 32V (dc)
400mA, maximum open circuit voltage of 25V (dc), typical 8V (dc) at 80mA
Maximum output sink current per output is 1.5A (external class 2 or SELV* supply required)
Total sink current for all outputs not to exceed 8A
Do not connect outputs in parallel
Safety Extra Low Voltage

FMHA – [C] A A A – A _

Open Collector Outputs

Switched DC

User selectable voltage, 5V (dc) at 130mA or 19 to 22V (dc) at 80mA

Switched DC Outputs

Tri-Process/Retransmit Outputs

0 to 20mA into 400Ω maximum load
0 to 10V (dc) into 4 kΩ minimum load
Outputs are scalable
Output supplies power
Each output can be independently set for voltage or current
Output may be used as retransmit or control

FMHA – [F] A A A – A _

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-18

Four Mechanical Relays, Form A

5A at 240VÅ (ac) or 30V (dc) maximum resistive load
20mA at 24V minimum load
125 VA pilot duty @ 120/240VÅ (ac), 25 VA at 24VÅ (ac)
100,000 cycles at rated load
Output does not supply power.
For use with ac or dc
See Quencharc note (page 4)

Note
Not 60730 compliant.

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-20

Dual 10A Solid-State Relays, Form A

10A at 20 to 264VÅ (ac) maximum resistive load
10A per output at 240VÅ (ac), max. 20A per card at 122°F (50°C), max. 12A per card at 149°F (65°C)
Opto-isolated, without contact suppression
Maximum off state leakage of 105μA
Output does not supply power
Do not use on dc loads.
Requires two slots

FMHA – [K] A A A – A _

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-22

Note
This module requires 2 slots, therefore it cannot be placed in slot 3 or 6.

Note
Not 60730 compliant.

Four 2A Solid-State Relays, Form A

2A at 20 to 264VÅ (ac) maximum resistive load
50 VA 120/240VÅ (ac) pilot duty
Optical isolation, without contact suppression
Maximum off state leakage of 105μA
Output does not supply power.
Do not use on dc loads.
N.O., COM, N.O wiring (shared common) between each set of outputs.
See derating curve below for maximum current output.

FMHA – [L] A A A – A _

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-25

3 Mechanical Relays, 2 Form C, 1 Form A

5A at 24 to 240VÅ (ac) or 30V (dc) maximum resistive load
125 VA pilot duty 120/240VÅ (ac) 25 VA at 24VÅ (ac)
Output does not supply power
Form A relay shares common with one Form C relay.
See Quencharc note

FMHA – [B] A A A – A _

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-27

Warranty

F4T/D4T Flex modules are manufactured by ISO 9001 registered processes and are backed by a three-year warranty to the first purchaser for use, providing that the modules have not been misapplied.

Technical Assistance

To get assistance from Watlow:

Contact a local representative: see last page
Email: wintechsupport@watlow.com
Call: +1 507-494-5656 from 7 a.m. to 5 p.m. Central Standard Time (CST)

Symbol	Explanation

Unit is compliant with European Union directives. See Declaration of Conformity for further details on directives and standards used for compliance.

| Unit has been reviewed and approved by CSA Inter- national for use as Temperature Indicating-Regulating Equipment per CSA C22.2 No. 24. See: www .csa-inter- national.org
| Recognized component UL Files E185611 Process Control Equipment and E43684 Automatic Temperature Sensing Control Integrated Equipment, see conditions of acceptability.

Specifications

Input Type

| Max Error @ 25 Deg C| Accuracy Range| Operating Range|

Units

---|---|---|---|---
Low| High| Low| High
J| ±1.75| 0| 750| -210| 1200| Deg| C
K| ±2.45| -200| 1250| -270| 1371| Deg| C
*T (-200 to

| ±1.55| -200| 350| -270| 400| Deg| C
N| ±2.25| 0| 1250| -270| 1300| Deg| C
*E| ±2.10| -200| 900| -270| 1000| Deg| C
R| ±3.9| 0| 1450| -50| 1767| Deg| C
S| ±3.9| 0| 1450| -50| 1767| Deg| C
B| ±2.66| 870| 1700| -50| 1816| Deg| C
C| ±3.32| 0| 2315| 0| 2315| Deg| C
D| ±3.32| 0| 2315| 0| 2315| Deg| C
F (PTII)| ±2.34| 0| 1343| 0| 1343| Deg| C

Input Type

| Max Error @ 25 Deg C| Accuracy Range| Operating Range|

Units

---|---|---|---|---
Low| High| Low| High
*RTD, 100Ω| ±2.00| -200| 800| -200| 800| Deg C

RTD, 1kΩ

| ****

±2.00

| ****

-200

| ****

800

| ****

-200

| ****

800

| ****

Deg C

mV| ±0.05| 0| 50| –| –| –| –| –| –| mV
Volts| ±0.01| 0| 10| –| –| –| –| –| –| Volts
mAdc| ±0.02| 2| 20| –| –| –| –| –| –| mA DC
mAac| ±5| -50| 50| –| –| –| –| –| –| mA AC
Potenti- ometer 1k range| ****

±1

| ****

0

| ****

1000

| ****

–

| ****

–

| ****

–

| ****

–

| ****

–

| ****

–

| ****

Ohms

NSF approved inputs

Thermistor Input

Input Type| Max Error @ 25 Deg C| Accuracy Range| Units
Low| High
Thermistor, 5k range| ±5| 0| 5000| Ohms
Thermistor, 10k range| ±10| 0| 10000| Ohms
Thermistor, 20k range| ±20| 0| 20000| Ohms
Thermistor, 40k range| ±40| 0| 40000| Ohms

Declaration of Conformity

WATLOW Electric Manufacturing Company ISO 9001since 1996.
1241 Bundy Blvd. Winona, MN 55987 USA
Designation:Series EZ-ZONE®Flex ModulesModel Numbers:FMLA-(LAJ, LCJ, LEJ, MAJ, MCJ, MEJ, YEB1)A1-A1(A1,F1,B1,G1)X1X1FMMA-X1(A1,C1,E,F1,K)(A1,C1,H,J,K)A1-A1(A1,F1,B1,G1)X1X1FMHA-(R1,P1,C1,F1,B1,J,K,L1)A1A1A1-A1(A1,F1,B1,G1)X1X11FMCA-XAAA-A(A,F,B,G)XX;
Note: X1= Any letter or numberClassification:FMLA, FMMA and FMHA are Process Controlmodules, FMCAare Communication modules; Modules are Integrated Controlsin either EZ-ZONE®CC,F4Tor D4TBases;Modules are IP10when properly installed.Rated Voltage and
Frequency:Relay, SSR or No-Arc Control outputs 24 to240 V~ (ac)50/60 Hz, Switched DC, Processand communications;low voltage SELVRated Power Consumption:See manual for de-ratingat increase dtemperatures.No-arc relays 15A1.C, Dual SSR module 1.C 10A each output,
Mechanical relay 5A125 VA,25 VA at 24 V~ (ac)1.B,Discreet SSR 1/2A1.C 20VA, Quad SSR 1.C 1.5A50 VA, Hex I/O ELV 1.5A, all others SELV limited energy.Flex Modules are considered components and have no function in and of themselves, it is only when installed inaWatlowEZ-
ZONE®CC, Series F4Tor Series D4TBase enclosure that they have useful function. Modules were tested as parts of these systems for compliance with the following directives.

2014/30/EUElectromagnetic Compatibility DirectiveEN 61326-1:2013Electrical equipment for measurement, control and laboratory use –EMC requirements (Industrial Immunity, Class B Emissions).

2014/35/EULow-Voltage Directive

EN 61010-1:2010All options compliantSafety Requirements of electrical equipment for measurement, control and laboratory use. Part 1: General requirements
EN 60730-1:2011EN 60730-2-9:20101Food Service Compliant options.Automatic electrical controls for household and similar
use –Particular requirements for temperature sensing controls.Only certain output options comply with 60730 spacing and dielectric requirements, see order information for compatible models.

Compliant with 2011/65/EURoHS2Directive

Per 2012/19/EU W.E.E.E Directive, Please Recycle Properly.
See the Declarations of Conformity forWatlowEZ-ZONE®CC,SeriesF4T and Series D4Tmodelsfor further details on standards used for compliance.

WATLOW-FMHA-0600-0096-0000-High-Density-Input-Output-Modules-
FIG-32