Delfield 6100XL Series Reach In Freezers Instruction Manual

June 13, 2024
DELFIELD

6100XL Series Reach In Freezers

Product Information

Product Name: Fresh Solutions, Fit For You 6000XL & 6100XL
Series Reach Ins

Part Number: 9294254 01/23

Manufacturer: MTW Kitchen Care

Website: www.mtwkitchencare.com

This manual is updated as new information and models are
released. Visit our website for the latest manual.

Safety Notices

  • Warning: Read this manual thoroughly before
    operating, installing or performing maintenance on the equipment.
    Failure to follow instructions in this manual can cause property
    damage, injury or death.

  • Danger: Do not install or operate equipment
    that has been misused, abused, neglected, damaged, or
    altered/modified from that of original manufactured
    specifications.

  • Danger: Keep power cord AWAY from HEATED
    surfaces. DO NOT immerse power cord or plug in water. DO NOT let
    power cord hang over edge of table or counter.

  • Danger: All utility connections and fixtures
    must be maintained in accordance with Local and national
    codes.

  • Warning: Authorized Service Representatives
    are obligated to follow industry standard safety procedures,
    including, but not limited to, local/national regulations for
    disconnection/lock out/tag out procedures for all utilities
    including electric, gas, water and steam.

  • Warning: Do not store or use gasoline or other
    flammable vapors or liquids in the vicinity of this or any other
    appliance. Never use flammable oil soaked cloths or combustible
    cleaning solutions, for cleaning.

  • Warning: Do not use electrical appliances or
    accessories other than those supplied by the manufacturer.

  • Warning: Use caution when handling metal
    surface edges of all equipment.

  • Warning: This appliance is not intended for
    use by persons (including children) with reduced physical, sensory
    or mental capabilities, or lack of experience and knowledge, unless
    they have been given supervision concerning use of the appliance by
    a person responsible for their safety. Do not allow children to
    play with this appliance.

  • Caution: Use caution handling, moving and use
    of the R290 refrigerators to avoid either damaging the refrigerant
    tubing or increasing the risk of a leak. Components shall be
    replaced with like components. Servicing shall be done by a factory
    authorized service personnel to minimize the risk of possible
    ignition due to incorrect parts or improper service.

  • Notice: Proper installation, care and
    maintenance are essential for maximum performance and trouble-free
    operation of your equipment. Visit our website
    www.mtwkitchencare.com for manual updates, translations, or contact
    information for service agents in your area.

  • Notice: This product utilizes Ecomate blowing
    agent methyl formate.

Table of Contents

  1. Section 1 General Information
  2. Section 2 Installation
  3. Section 3 Operation
  4. Section 4 Maintenance
  5. Section 5 Troubleshooting

Fresh Solutions, Fit For You
6000XL & 6100XL Series
Reach Ins
Original Instructions Installation, Operation and Maintenance Manual
This manual is updated as new information and models are released. Visit our website for the latest manual.
Part Number: 9294254 01/23

Safety Notices
nWarning
Read this manual thoroughly before operating, installing or performing maintenance on the equipment. Failure to follow instructions in this manual can cause property damage, injury or death.
DANGER Do not install or operate equipment that has been misused, abused, neglected, damaged, or altered/ modified from that of original manufactured specifications.
DANGER Keep power cord AWAY from HEATED surfaces. DO NOT immerse power cord or plug in water. DO NOT let power cord hang over edge of table or counter.
DANGER All utility connections and fixtures must be maintained in accordance with Local and national codes.
nWarning
Authorized Service Representatives are obligated to follow industry standard safety procedures, including, but not limited to, local/national regulations for disconnection / lock out / tag out procedures for all utilities including electric, gas, water and steam.
nWarning
Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. Never use flammable oil soaked cloths or combustible cleaning solutions, for cleaning.
nWarning
This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. Operation, installation, and servicing of this product could expose you to airborne particles of glasswool or ceramic fibers, crystalline silica, and/or carbon monoxide. Inhalation of airborne particles of glasswool or ceramic fibers is known to the State of California to cause cancer. Inhalation of carbon monoxide is known to the State of California to cause birth defects or other reproductive harm.

nWarning
Do not use electrical appliances or accessories other than those supplied by the manufacturer.
nWarning
Use caution when handling metal surface edges of all equipment.
nWarning
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision concerning use of the appliance by a person responsible for their safety. Do not allow children to play with this appliance.
,Caution
Use caution handling, moving and use of the R290 refrigerators to avoid either damaging the refrigerant tubing or increasing the risk of a leak. Components shall be replaced with like components. Servicing shall be done by a factory authorized service personnel to minimize the risk of possible ignition due to incorrect parts or improper service.
N otice Proper installation, care and maintenance are essential for maximum performance and trouble-free operation of your equipment. Visit our website www. mtwkitchencare.com for manual updates, translations, or contact information for service agents in your area.
N otice This product utilizes Ecomate blowing agent methyl formate

Table of Contents

Section 1 General Information Section 2 Installation
Section 3 Operation
Section 4 Maintenance
Section 5 Troubleshooting

Model Numbers…………………………………………………………………………………………………… 5 Serial Number Information ………………………………………………………………………………….. 5 Warranty Information ………………………………………………………………………………………….. 5 Regulatory Certifications …………………………………………………………………………………….. 5
Location ……………………………………………………………………………………………………………… 7 Weight of Equipment …………………………………………………………………………………………… 8 Clearance Requirements………………………………………………………………………………………. 8 Drain Connections……………………………………………………………………………………………….. 8 Dimensions …………………………………………………………………………………………………………. 9 Electrical Service ………………………………………………………………………………………………..10 Energy Star ………………………………………………………………………………………………………..11 Refrigeration ……………………………………………………………………………………………………..11 Leveling……………………………………………………………………………………………………………..11 Stabilizing …………………………………………………………………………………………………………. 11 Leg & Caster Installation……………………………………………………………………………………..11
R290 Controls/Programming/Settings…………………………………………………………………14 Refrigerator Settings ………………………………………………………………………………………………………….. 14 Refrigerator Defrost……………………………………………………………………………………………………………. 14 Freezer Settings ………………………………………………………………………………………………………………….. 15 Freezer Defrost ……………………………………………………………………………………………………………………. 15 R290 Temperature Control & Display ………………………………………………………………………………. 16 R290 Evaporator Fan Operation……………………………………………………………………………………….. 16 R290 Changing Display from Fahrenheit to Celsius on ERC112 Control……………………. 17
Cleaning and Sanitizing Procedures…………………………………………………………………….19 General…………………………………………………………………………………………………………………………………. 19 Interior Cleaning…………………………………………………………………………………………………………………. 20 Exterior Cleaning………………………………………………………………………………………………………………… 20 Drain……………………………………………………………………………………………………………………………………… 21 Cleaning the Condenser Coil ……………………………………………………………………………………………. 21 Casters ………………………………………………………………………………………………………………………………….. 21 Doors/Hinges………………………………………………………………………………………………………………………. 21 Preventing Blower Coil Corrosion ……………………………………………………………………………………. 21
Problem -> Cause -> Correction Chart………………………………………………………………….22

Part Number: 9294254 01/23

3

Table of Contents (continued) THIS PAGE INTENTIONALLY LEFT BLANK

4

Part Number: 9294254 01/23

Section 1 General Information

Model Numbers
This manual covers the following models: 1 Section Refrigerators Solid Doors 6025XL-S
1 Section Freezer Solid Doors 6125XL-S

Serial Number Information
The serial number is on the identification plate that also includes the model number. The identification plate is located inside the cabinet on the left interior wall. Always have the serial number of your unit available when calling for parts or service.
Warranty Information
Visit http://www.delfield.com/warranty to: · Register your product for warranty. · Verify warranty information. · View and download a copy of your warranty.
Regulatory Certifications
Models are certified by:

·

National Sanitation Foundation (NSF)

·

Underwriters Laboratories (UL)

·

Underwriters Laboratories of Canada (cUL)

Part Number: 929254 01/23

5

General Information

Section 1

THIS PAGE INTENTIONALLY LEFT BLANK

6

Part Number: 9294254 01/23

Section 2 Installation

DANGER Installation must comply with all applicable fire and health codes in your jurisdiction.
DANGER Use appropriate safety equipment during installation and servicing.
nWarning
Do not damage the refrigeration circuit when installing, maintaining or servicing the unit.
Location
nWarning
This equipment must be positioned so that the plug is accessible unless other means for disconnection from the power supply (e.g., circuit breaker or disconnect switch) is provided.
nWarning
Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical conduit or gas lines.
nWarning
To avoid instability the installation area must be capable of supporting the combined weight of the equipment and product. Additionally the equipment must be level side to side and front to back.
nWarning
This equipment is intended for indoor use only. Do not install or operate this equipment in outdoor areas.

The location selected for the equipment must meet the following criteria. If any of these criteria are not met, select another location.
· The location MUST be level, stable and capable of supporting the weight of the equipment.
· The location MUST be free from and clear of combustible materials.
· Equipment MUST be level both front to back and side to side.
· Position the equipment so it will not tip or slide.
· Front casters MUST be locked once positioned.
· Recommended air temperature is 60° – 100°F (16° – 38°C).
· Proper air supply for ventilation is REQUIRED AND CRITICAL for safe and efficient operation. Refer to Clearance Requirements chart on page 8.
· Do not obstruct the flow of ventilation air. Make sure the air vents of the equipment are not blocked.
· Do not install the equipment directly over a drain. Steam rising up out of the drain will adversely affect operation, air circulation, and damage electrical / electronic components.

Part Number: 9294254 01/23

7

Installation

Section 2

Weight of Equipment

Description Solid Doors Solid Doors

Models

Weight

1 Section Refrigerators

6025XL-S

274 lbs (124 kg)

1 Section Freezers

6125XL-S

274 lbs (124 kg)

Clearance Requirements
DANGER Minimum clearance requirements are the same for noncombustible locations as for combustible locations. The flooring under the appliance must be made of a noncombustible material.

DANGER
Risk of fire/shock. All minimum clearances must be maintained. Do not obstruct vents or openings.

Top

6025XL-S

12.00″ (30cm)

6125XL-S

20.00″ (50cm)

· Keep the vents clean and free of obstruction.

· Casters or optional legs must be used and not removed.

Drain Connections
nWarning
Moisture collecting from improper drainage can create a slippery surface on the floor and a hazard to employees. It is the owner’s responsibility to provide a container or outlet for drainage.

8

Part Number: 9294254 01/23

Section 2

Dimensions

Model 6025XL-S
6125XL-S

Length

Depth

1 Section Refrigerators

25.5″ (65cm)

32.38″ (82cm)

1 Section Freezers

25.5″ (65cm)

32.38″ (82cm)

Height
79.5″ (202cm)
79.5″ (202cm)

Installation

6025XL-S 6125XL-S

Model

Volume

1 Section Refrigerators

20ft3 (595L)

1 Section Freezers

20ft3 (595L)

Part Number: 9294254 01/23

9

Installation

Section 2

Electrical Service
DANGER Check all wiring connections, including factory terminals, before operation. Connections can become loose during shipment and installation.
nWarning
This appliance must be grounded and all field wiring must conform to all applicable local and national codes. Refer to rating plate for proper voltage. It is the responsibility of the end user to provide the disconnect means to satisfy the authority having jurisdiction.

Rated Amperages, Horsepower, Voltage & Power Cord Chart
Maximum 10ft (3m) cord with plug.

Models

Amps HP V, Hz, Ph NEMA Plug

6025XL-S(H) 4.2 0.22 120, 60, 1 5-15p

6125XL-S(H) 5.5 0.55 120, 60, 1 5-15p

Freezers Refrigerators 1 Section 1 Section

· Plug units with R290 refrigerant into a receptacle that is a minimum of 14″ (36cm) above the floor.
· All electrical work, including wire routing and grounding, must conform to local, state and national electrical codes.
· The equipment must be grounded.
· A separate fuse/circuit breaker must be provided for each unit.
· Check all green ground screws, cables and wire connections to verify they are tight before start-up.
· The maximum allowable voltage variation is ±10% of the rated voltage at equipment start-up (when the electrical load is highest).
Ground Fault Circuit Interrupter
Ground Fault Circuit Interrupter (GFCI/GFI) protection is a system that shuts down the electric circuit (opens it) when it senses an unexpected loss of power, presumably to ground. Manitowoc does not recommend the use of GFCI/GFI circuit protection to energize our equipment. If code requires the use of a GFCI/GFI then you must follow the local code. The circuit must be dedicated, sized properly and there must be a panel GFCI/GFI breaker. We do not recommend the use of GFCI/GFI outlets to energize our equipment as they are known for more intermittent nuisance trips than panel breakers.

10

Part Number: 9294254 01/23

Freezers 1 Section

Section 2

Energy Use For Energy Star® Certified Units

Models

Energy Use in kWh

6025XL-S

1.66

Refrigerators 1 Section

6125XL-S

5.78

Installation

Refrigeration

Model

BTU/Hour Capacity

Heat of Rejection
(BTU)

1 Section Refrigerators

R290 Charge

Solid

Full Height Doors 6025XL-S

1754

390

113g

1 Section Freezers

Solid

Full Height Doors 6125XL-S

1759

755

100g

Leveling
After the cabinet has been placed in the desired location, cabinets with legs must be leveled. Level units from front to back and from side to side. Leveling will insure proper door operation and removal of condensate. Cabinets with casters must have the caster brake set so the cabinet cannot move.
Stabilizing
It is very important that all legs are properly adjusted to keep the cabinet level, evenly distribute the weight and to make sure the unit will not rock, lean or be unstable.
Leg & Caster Installation
DANGER Legs or casters must be installed and the legs or casters must be screwed in completely to prevent bending. When casters are installed the mass of this unit will allow it to move uncontrolled on an inclined surface. These units must be tethered/secured to comply with all applicable codes.
nWarning
The unit must be installed in a stable condition with the front wheels locked. Locking the front casters after installation is the owner’s and operator’s responsibility.
nWarning
Single Section models with glass doors or drawers are supplied with flanged feet that must be fastened to the floor to prevent the unit from tipping when the door/ drawer(s) are opened.

Part Number: 9294254 01/23

11

Installation
nWarning
Use a jack to lift the refrigeration unit off the ground just far enough to remove the leg/caster. Place blocking underneath the unit. Do not work underneath a raised unit without proper blocking. Do not lift the unit more than necessary to remove the leg/caster. Lifting the unit too far can make the unit unstable.
,Caution
All single-section units require that the swivel casters be mounted on the front and rigid casters be mounted on the rear.
To install the legs or casters: 1. Remove unit from skid.
NOTE: The bolts used to hold the unit to the skid should be re-used as the fourth hex head bolt for each caster or leg plate installation. The bolt should not measure over 2″ (5cm) in length.
2. Raise unit to access leg/caster mounting holes on bottom of unit.
3. Attach the legs or casters to bottom of cabinet using hex head bolts.

Section 2

12

Part Number: 9294254 01/23

Section 2

Installation

THIS PAGE INTENTIONALLY LEFT BLANK

Part Number: 9294254 01/23

13

Section 3 Operation

DANGER Do not operate any appliance with a damaged cord or plug. All repairs must be performed by a qualified service company.
DANGER Never stand on the unit! They are not designed to hold the weight of an adult, and may collapse or tip if misused in this manner.
nWarning
Do not contact moving parts.
nWarning
All covers and access panels must be in place and properly secured, before operating this equipment.
nWarning
Do not use electrical appliances inside the food storage compartment of this appliance.
nWarning
The operator of this equipment is solely responsible for ensuring safe holding temperature levels for all food items. Failure to do so could result in unsafe food products for customers.
nWarning
Overloading shelves can damage equipment or cause bodily injury.
nWarning
Damp or wet hands may stick to cold surfaces.
nWarning
Do not block the supply and return air grills or the air space around the air grills. Keep plastic wrappings, paper, labels, etc. from being airborne and lodging in the grills. Failure to keep the air grills clear will result in unsatisfactory operation of the system.
,Caution
Do not throw items into the storage area. Failure to heed this recommendation could result in damage to the interior of the cabinet or to the blower coil.

R290 Controls/Programming/Settings
R290 Refrigerator
Refrigerators are factory set at mid-range to maintain about 38ºF (3ºC) box temperature.
1. At initial start-up or anytime power is disconnected, then reconnected to the unit, the control will go into defrost mode.
2. The control will enter a DEFROST mode and the display will read dEF. The compressor and condenser fan as well as the evaporator fan will remain off until this initial defrost is complete. This initial defrost cycle may take up to 35 minutes to complete.
3. The display will continue to read dEF for an additional 30 minutes while the cooling cycle cools the box to the set temperature.
4. Then the digital thermostat will display box temperature.
5. The temperature control will cycle the compressor, evaporator fan motor and condenser fan motor to maintain box temperature at the control setting. For more information see R290 Evaporator Fan Operation on page 16.
R290 Refrigerator Defrost
The temperature control also monitors the evaporator temperature and will turn off the compressor and condenser fan motor when needed to allow accumulated frost on the evaporator to clear. During this defrost cycle, the digital temperature display will read dEF. After the defrost cycle is complete, the temperature control will return to a normal cooling cycle, but the display will continue to read dEF until the evaporator returns to normal cooling temperatures (up to 30 minutes).

Part Number: 9294254 01/23

14

Section 3

Operation

R290 Freezer
Freezers are factory set at mid-range to maintain about -2ºF (-19ºC) box temperature.
1. At initial start-up or anytime power is disconnected, then reconnected to the unit, the control will go into defrost mode
2. The control will enter a DEFROST mode and the display will read dEF. The compressor and condenser fan as well as the evaporator fan will remain off until this initial defrost is complete. This initial defrost cycle may take up to 35 minutes to complete.
3. The display will continue to read dEF for an additional 30 minutes while the freezing cycle cools the box to the set temperature.
4. Then the thermostat will display box temperature.
5. The temperature control will cycle the compressor, evaporator fan motor and condenser fan motor to maintain box temperature at the control setting. For more information see R290 Evaporator Fan Operation on page 16.
R290 Freezer Automatic Defrost
The control also monitors compressor total running time and will enter a defrost cycle after total compressor running time is greater than seven hours since the last defrost cycle OR if evaporator coil temperature drops below -30ºF (-34ºC) (indicating excessive frost on the coil).
R290 Freezer Manual Defrost
If a manual defrost is desired, hold the upper left button for five seconds or unplug the unit for several seconds, then plug unit back in. This will cause the control to re-initialize and then enter a defrost cycle.
When the control enters the defrost mode, it switches off the evaporator fan motor, compressor and condenser fan motor, and switches on the defrost heater to warm the evaporator coil. Thereby melting all frost accumulated during the previous refrigeration cycle. The digital temperature display will now read dEF. The control will continue the defrost cycle for a MINIMUM of six minutes and a MAXIMUM of 35 minutes depending on the amount of frost accumulated on the evaporator coil.
After the defrost cycle is complete, the control returns to a normal refrigeration cycle, however the evaporator fan motor will not switch on until the evaporator reaches -5°F (-21°C) or two minutes AFTER the compressor and condenser fan motor have begun operating. The digital temperature display will continue to read dEF until the evaporator has returned to normal freezing temperatures (up to 30 minutes).

CONTROL & DISPLAY R290 TEMPERATURE CONTROL & DISPLAY

Control Display

Operation / Indication

Status

Displayed

Comments

Normal (°C) Normal (°F)

Temp. [°C] Temp. [°F]

Unit depends on setting (parameters in control)

Show set-point

Temp.

Set to Defrost

dEF / Temp

Depends on setting (parameters in control or as chosen by upper
left button)

Sensor 1 defect

E01

X

Air sensor

Sensor 2 defect

E02

X

Coil sensor

Sensor 3 defect

E03

X

Open

Sensor 4 defect

E04

X

Open

High temperature alarm

Hi

X Automatically switching

at 2 sec rate

Low temperature alarm Lo

X

Line voltage too high, uHi

X

above 140 volts

Line voltage too low,

uLi

X

below 96 volts

Control calls for cooling LEA for more than 24 hours straight

X Time includes defrost. Error will go away if the control cycles off the compressor or if the power is shut off. If error is on a cold pan it could be related to a high ambient temperature or not shutting the rail off nightly.

All alarms sound for approximately 10 seconds and then are silent for 50 seconds. It will do that for 15 cycles and then remain silent. The alarm code will still be present on the display until the fault clears.

Part Number: 9294254 01/23

15

Operation

Section 3

R290 Temperature Control & Display Operation
Press upper or lower right button. · Display show actual set-point (blinking).
» If buttons untouched for 3 seconds returns to normal. · Increase set-point by pressing upper button. Max value
depends on parameters in control. · Decrease set-point by pressing lower button. Min value
depends on parameters in control. » If buttons untouched for 3 seconds returns to normal
and stores new set-point. Press upper left button for 5 seconds. · Start defrost.
Press lower left button for 5 seconds. · Unit goes into stand-by mode.
» The display will read off, then a period. · Press the lower left button again for 5 seconds.
» The display will read on. » The unit will then start up in the defrost mode, and
display will read dEF.
R290 Power Switch All freezers and refrigerators are equipped with a power disconnect switch located behind the louvered end panel. Switch must be in the on position for the unit to operate. If the switch is turned off, then returned to the on position, the unit will enter a defrost cycle and the display will read dEF.

R290 Energy Saver Switch
Select freezers are equipped with an energy saver switch for service use. It is located in the electrical box behind the front shroud. It controls the length of time that heat is applied to the door perimeter. The normal operating position for this switch is the on position, providing the shortest amount of time. If excessive condensation is observed on the door opening, switch to the off position with the help of an authorized service agent. The off position will increase the length of time the door heater is on.
R290 Temperature Alarm
The alarm will sound and flash “HI” or “LO” 90 minutes after the unit has reached its alarm temperature point or after any power interruption if the temperature is above or below the alarm set points. Refrigerators are factory set at mid-range to maintain about 38ºF (3ºC) box temperature. The high refrigerator temperature point is 50°F (10°C). The low refrigerator temperature point is 25°F (-4°C). Freezers are factory set at mid-range to maintain about -2ºF (-19ºC) box temperature. The high freezer temperature point is 20°F (-7°C). Freezers do not have a low temperature point.
R290 EVAPORATOR FAN OPERATION
Depending on the units requirements, units may have evaporator fans that run continually or cycle on and off when power is applied. If you have a unit that you notice the fan is cycling, please see the operations sequence below.
During normal operation the evaporator fan may cycle and/or pulse independently of the compressor. Consult Technical Support at 1-844-724-CARE if you are unsure of the proper function.

Cooling Cycle

Compressor Compressor

On

Off

Defrost Cycle
Compressor Off

Evap Fan On
Evap Fan Off
Evap Fan On
Evap Fan Off
Evap Fan On
Evap Fan Off

Refrigerator X

Freezer

X

Cycles On 2-Min, X Off 2-Min

X

X

16

Part Number: 9294254 01/23

Section 3
R290 CHANGING DISPLAY FROM FAHRENHEIT TO CELSIUS ON ERC112 CONTROL 1. Simultaneously hold the up and down arrows for
5 seconds to access menu for password protected parameters.

Operation
6. -F should be displayed indicating Fahrenheit. Use the down arrow to change it to -C for Celsius and hit the stand-by button (lower left button) to enter the change.

2. Screen should temporarily flash PAS and then move to a numeric screen.

3. Scroll to 187 using the up/down arrows and push the stand-by button (lower left button) to enter.

7. Push the defrost button (upper left button) to move out of the display unit menu.

4. Scroll to dis using the up/down arrows and push the stand-by button (lower left button) to enter into the display menu.

8. Push the defrost button (upper left button) to move out of the display menu and back to the normal display.
NOTE: For steps 7 and 8, display will return back to normal display after 30 seconds of inactivity.

5. Scroll to CFu using the up/down arrows and push the stand-by button (lower left button) to enter the display unit menu.

Part Number: 9294254 01/23

17

Operation

Section 3

THIS PAGE INTENTIONALLY LEFT BLANK

18

Part Number: 9294254 01/23

Section 4 Maintenance

DANGER It is the responsibility of the equipment owner to perform a Personal Protective Equipment Hazard Assessment to ensure adequate protection during maintenance procedures.
DANGER Failure to disconnect the power at the main power supply disconnect could result in serious injury or death. The power switch DOES NOT disconnect all incoming power.
DANGER Disconnect electric power at the main power disconnect for all equipment being serviced. Observe correct polarity of incoming line voltage. Incorrect polarity can lead to erratic operation.
nWarning
Never use sharp objects or tools to remove ice or frost. Do not use mechanical devices or other means to accelerate the defrosting process.

Cleaning and Sanitizing Procedures
,Caution
Maintenance and servicing work other than cleaning as described in this manual must be done by an authorized service personnel.
GENERAL
nWarning
When using cleaning fluids or chemicals, rubber gloves and eye protection (and/or face shield) must be worn.
You are responsible for maintaining the equipment in accordance with the instructions in this manual. Maintenance procedures are not covered by the warranty.

Maintenance
Interior Gasket Exterior Drain Condenser Coil Casters

Daily
X X X

Weekly X

Monthly
X X

After Prolonged Shutdown X X X X X X

At Start-Up
X X X X X X

Part Number: 9294254 01/23

19

Maintenance

Section 4

INTERIOR CLEANING
Notice When cleaning interior and exterior of unit, care should be taken to avoid the front power switch and the rear power cord. Keep water and/or cleaning solutions away from these parts.
Notice Never use a high-pressure water jet for cleaning or hose down or flood interior or exterior of units with water. Do not use power cleaning equipment, steel wool, scrapers or wire brushes on stainless steel or painted surfaces.
The interior can be cleaned using soap and warm water. If this isn’t sufficient, try ammonia and water or a nonabrasive liquid cleaner.

EXTERIOR CLEANING
Notice
Never use an acid based cleaning solution on exterior panels! Many food products have an acidic content, which can deteriorate the finish. Be sure to clean the stainless steel surfaces of ALL food products.
Clean the area around the unit as often as necessary to maintain cleanliness and efficient operation.
Wipe gasket and surfaces with a damp cloth rinsed in water to remove dust and dirt from the outside of the unit. Always rub with the “grain” of the stainless steel to avoid marring the finish. If a greasy residue persists, use a damp cloth rinsed in a mild dish soap and water solution. Wipe dry with a clean, soft cloth.
Never use steel wool or abrasive pads for cleaning. Never use chlorinated, citrus based or abrasive cleaners.
Stainless steel exterior panels have a clear coating that is stain resistant and easy to clean. Products containing abrasives will damage the coating and scratch the panels. Daily cleaning may be followed by an application of stainless steel cleaner which will eliminate water spotting and fingerprints. Early signs of stainless steel breakdown are small pits and cracks. If this has begun, clean thoroughly and start to apply stainless steel cleaners in attempt to restore the steel.

20

Part Number: 9294254 01/23

Section 4

Maintenance

DRAIN
Each unit has a drain located inside the unit that removes the condensation from the evaporator coil and routes it to an external condensate evaporator pan. Each drain can become loose or disconnected during normal use. If you notice water accumulation on the inside of the unit, be sure the drain tube is connected to the evaporator drain pan. If water is collecting underneath the unit, make sure the end of the drain tube is in the condensate evaporator. The leveling of the unit is important as the units are designed to drain properly when level. Be sure all drain lines are free of obstructions.
CLEANING THE CONDENSER COIL
In order to maintain proper refrigeration performance, the condenser fins must be cleaned of dust, dirt and grease regularly. It is recommended that this be done monthly. If conditions are such that the condenser is totally blocked in a month, the frequency of cleaning should be increased. Clean the condenser with a vacuum cleaner or stiff brush. If extremely dirty, a commercially available condenser cleaner may be required.
Failure to maintain a clean condenser coil can initially cause high temperatures and excessive run times. Continuous operation with a dirty or clogged condenser coil can result in compressor failure. Neglecting the condenser coil cleaning procedures will void any warranties associated with the compressor and cost to replace the compressor.
CASTERS
Wipe casters with a damp cloth monthly to prevent corrosion.

DOORS/HINGES
Over time and with heavy-use doors, the hinges may become loose. If this happens, tighten the screws that mount the hinge brackets to the frame of the unit. Loose or sagging doors can cause the hinges to pull out of the frame, which may damage both the doors and the hinges. In some cases this may require qualified service agents or maintenance personnel to perform repairs.
PREVENTING BLOWER COIL CORROSION
To help prevent corrosion of the blower coil, store all acidic items, such as pickles and tomatoes, in seal-able containers. Immediately wipe up all spills.

Part Number: 9294254 01/23

21

Troubleshooting

Section 5

THIS PAGE INTENTIONALLY LEFT BLANK

22

Part Number: 9294254 11/17

Section 5

Troubleshooting

THIS PAGE INTENTIONALLY LEFT BLANK

Part Number: 9294254 11/17

23

DELFIELD 980 SOUTH ISABELLA ROAD, MOUNT PLEASANT, MI 48858
800-733-8821 WWW.DELFIELD.COM
©2019 Welbilt Inc. except where explicitly stated otherwise. All rights reserved. “Part Number 9294254 01/23

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DELFIELD User Manuals

Related Manuals