DELFIELD EHEI36C E-Chef Hot Food Table Instruction Manual

Fresh Solutions, Fit For You
EHEI36C E-Chef Hot Food Table
Instruction Manual

Original Instructions Installation, Operation, and Maintenance Manual

This manual is updated as new information and models are released. Visit our website for the latest manual.

Original Document
Part Number 9291472 12/21
Caution
Read this instruction before operating this equipment.

General Information

Warning
Read this manual thoroughly before operating, installing, or performing maintenance on the equipment. Failure Following instructions in this manual can cause property damage, injury, or death.
DANGER
Do not install or operate equipment that has been misused, abused, neglected, damaged, or altered/modified from that of original manufactured specifications.
DANGER
Never stand on the unit! They are not designed to hold the weight of an adult and may collapse or tip if misused.
warning
Authorized Service Representatives are obligated to follow industry-standard safety procedures, including, but not limited to, local/national regulations for disconnection / lock out / tag out procedures for all utilities including electric, gas, water, and steam.
Warning
Do not store or use gasoline or other flammable vapors or liquids within or around the vicinity of this or any other appliance. Never use flammable oil- soaked cloths or combustible cleaning solutions, for cleaning.
Warning
This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. Operation, installation, and servicing of this product could expose you to airborne particles of glasswool or ceramic fibers, crystalline silica, and/ or carbon monoxide. Inhalation of airborne particles of glasswool or ceramic fibers is known to the State of California to cause cancer. Inhalation of carbon monoxide is known to the State of California to cause birth defects or other reproductive harm.
Warning
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision concerning the use of the appliance by a person responsible for their safety. Do not allow children to play with this appliance.
Notice
Proper installation, care, and maintenance are essential for maximum performance and trouble-free operation of your equipment. Visit our website www.mtwkitchencare.com for manual updates, translations, or contact information for service agents in your area.
Notice
These appliances are intended to be used for commercial applications, for example in kitchens or restaurants, canteens, hospitals, and in commercial enterprises such as bakeries, butcheries, etc., but not for continuous mass production of food.
Notice
Climatic class 4 is defined as ambient conditions of 30°C and 55% relative humidity, according to ISO 23953-2.
Notice
This product utilizes Ecomate blowing agent methyl formate
Serial Number Location
The serial number on all E-Chef™ Series models is printed on the tag located on the interior side panel.
Always have the serial number of your unit available when calling for parts or services.
Warranty Information
Visit www.delfield.com/warranty to:

• Register your product for a warranty.
• Verify warranty information.
• View and download a copy of your warranty.

Regulatory Certifications
USA DOMESTIC MODELS ARE CERTIFIED BY:

• National Sanitation Foundation (NSF)
• Underwriters Laboratories (UL)
• Underwriters Laboratories of Canada (cUL)

EXPORT (-E) MODELS ARE CERTIFIED BY:

• National Sanitation Foundation (NSF)
• European Conformity Technical Inspection Association

Model Numbers
This manual covers the following E-Chef™ Hot Food Tables:

Installation

DANGER
Installation must comply with all applicable fire and health codes in your jurisdiction.
DANGER
Risk of fire/shock. All minimum clearances must be maintained. Do not obstruct vents or openings.
DANGER
Use appropriate safety equipment during installation and servicing.
DANGER
All utility connections and fixtures must be maintained in accordance with local and national codes.
Warning
Remove all removable panels before lifting and installing.
Warning
Use caution when handling metal surface edges of all equipment.
Location
Warning
These appliances are to be connected with flexible connections for equipotential bonding and connection to services such as electricity supply, water supply, gas supply, and steam supply such that the appliance can be moved in the direction required for cleaning for a distance not less than the dimension of the application in the direction of movement plus 500mm without the flexible connections becoming taught or being subject to strain.
Warning
To avoid instability the installation area must be capable of supporting the combined weight of the equipment and product. Additionally, the equipment must be level side to side and front to back.
Warning
This equipment is intended for indoor use only. Do not install or operate this equipment in outdoor areas. The location selected for the equipment must meet the following criteria. If any of these criteria are not met, select another location.

• Units are intended for indoor use only.
• The location MUST be level, stable, and capable of supporting the weight of the equipment.
• The location MUST be free from and clear of combustible materials.
• Do not install near objects or surfaces affected by heat or moisture.
• Equipment MUST be level both fronts to back and side to side.
• Position the equipment so it will not tip or slide.
• Recommended air temperature is 41° – 86°F (5° – 30°C).
• Proper air supply for ventilation is REQUIRED AND CRITICAL for safe and efficient operation. Refer to the Clearance Requirements chart on page 8.
• Do not install the equipment directly over a drain. Steam rising up out of the drain will adversely affect the operation, and air circulation, and damage electrical/electronic
  components.

Weight of Equipment

Notice
This symbol indicates the location of the equipotential bonding conductor connection.

Notice
This symbol indicates a hot surface that can cause injury to persons.

Clearance Requirements
DANGER
Minimum clearance requirements are the same for noncombustible locations as for combustible locations. The flooring under the appliance must be made of noncombustible material.

• The factory-installed legs must be used and not removed.

Dimensions

Capacity

Electrical Service
DANGER
Check all wiring connections, including factory terminals, before operation. Connections can become loose during shipment and installation.
Warning
This appliance must be grounded and all field wiring must conform to all applicable local and national codes. Refer to rating plate for proper voltage. It is the responsibility of
the end user to provide the disconnect means to satisfy the authority having jurisdiction.
All electrical work, including wire routing and grounding, must conform to local, state, and national electrical codes. The following precautions must be observed:

• The equipment must be grounded.

• A separate fuse/circuit breaker must be provided for each unit.

• A qualified electrician must determine the proper wire size dependent upon location, materials used, and length of run (minimum circuit ampacity can be used to help select
  the wire size).

• The maximum allowable voltage variation is ±10% of the rated voltage at equipment start-up (when the electrical load is highest).

• Check all green ground screws, cables, and wire connections to verify they are tight before start-up.

Leg Leveling
All four legs are adjustable. Adjust each leg until the unit is stable and level, both fronts to back and left to right. A level unit is necessary to maintain an equal water depth
throughout the wells.
Plumbing
Warning
Moisture collecting from improper drainage can create a slippery surface on the floor and a hazard to employees. It is the owner’s responsibility to provide a container or outlet for drainage.
A waste connection is provided 26.5” (67cm) above the floor, and 5.25” (13cm) from the right end. You must supply the required 1/2” (1.3cm) connection at the gate valve.
Notice
These appliances will operate within the marked rated voltage range without adjustment.

Operation

DANGER
The on-site supervisor is responsible for ensuring that operators are made aware of the inherent dangers of operating this equipment.
DANGER
Steam can cause serious burns. Always wear some type of protective covering on your hands and arms when removing lids or pans from the unit. Lift the lid or pan in a way that will direct escaping steam away from your face and body.
DANGER
Do not operate any appliance with a damaged cord or plug. All repairs must be performed by a qualified service company.
DANGER
Keep power cord AWAY from HEATED surfaces. DO NOT immerse the power cord in water. DO NOT let the power cord hang over the edge of the table or counter.
Warning
When operated dry, the good bottoms become very hot. Do not allow unprotected skin to contact any well surface.
Warning
The operator of this equipment is solely responsible for ensuring safe holding temperature levels for all food items. Failure to do so could result in unsafe food products for customers.
Warning
Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
Warning
All covers and access panels must be in place and properly secured, before operating this equipment.
Warning
Opening the drain cock will lead to the outflow of the hot contents of the bains-Marie.
Caution
Never use anything other than plain water in the wells or tanks. Failure to observe this warning may result in personal injury or damage to the unit.
Caution
Using ice in hot food well can cause condensation and damage to the well over time.
Before the unit is used the first time, turn the temperature knob to HI and heat the well for up to 30 minutes. Any residue or dust that adhered to the heater element(s) will be
burned off during this initial preheat period.
NOTE: Never place food directly into the well. Always use pans.
Although these models may be operated either with or without water in the wells, the wet operation is recommended. When using thick sauces always operate the hot food well filled with water. This will provide a more uniform temperature for the sauce.
Always place covers on pans when not serving to prevent food from drying out and to reduce your operating cost. For most efficient operation when empty or pre-heating,
keep covered insets in each well.
Do not put food down the drain.
WET OPERATION
Use only 4” (10cm) deep pans during wet operation.

1. Fill food well with 2” (50mm) of water. For quicker preheating, use hot water to fill the well.
2.  Turn the control to HI and pre-heat the warmer for 30 minutes. For the fastest pre-heating place covers or empty pans in the well.
3. After pre-heating, set the control to your desired serving temperature.

DRY OPERATION
Use only 6” (15.2cm) deep pans during dry operation. When operated dry, the bottom of the food well will discolor. A mild abrasive cleaner is recommended to clean this discoloration.

1. Pre-heat the well on HI for approximately 15 minutes. For the fastest pre-heating place covers or empty pans in the well.
2. After preheating, set the control to your desired serving temperature.

TEMPERATURE

THIS PAGE WAS INTENTIONALLY LEFT BLANK

Maintenance

DANGER
It is the responsibility of the equipment owner to perform a Personal Protective Equipment Hazard Assessment to ensure adequate protection during maintenance procedures.
DANGER
Failure to disconnect the power at the main power supply disconnect could result in serious injury or death. The power switch DOES NOT disconnect all incoming power.
DANGER
Disconnect electric power at the main power disconnect for all equipment being serviced. Observe the correct polarity of incoming line voltage. Incorrect polarity can lead to
erratic operation.
Warning
When cleaning the interior and exterior of the unit, avoid the front power switch and the rear power cord. Keep water and/or cleaning solutions away from these parts.
Warning
Never use a high-pressure water jet for cleaning or hosing down or flooding the interior or exterior of units with water. Do not use power cleaning equipment, steel wool, scrapers, or wire brushes on stainless steel or painted surfaces.
Warning
When using cleaning fluids or chemicals, rubber gloves and eye protection (and/or face shield) must be worn.
Caution
Never use an acid-based cleaning solution on exterior panels! Many food products have an acidic content, which can deteriorate the finish. Be sure to clean the stainless steel surfaces of ALL food products.
Caution
Maintenance and servicing work other than cleaning as described in this manual must be done by authorized service personnel.
General
You are responsible for maintaining the equipment in accordance with the instructions in this manual. Maintenance procedures are not covered by the warranty.
Stainless Steel Cleaning
Clean the unit and around it as often as necessary to maintain cleanliness and efficient operation. Wipe surfaces with a damp cloth rinsed in water to remove dust and dirt from the unit. Always rub with the “grain” of the stainless steel to avoid marring the finish. If a greasy residue persists, use a damp cloth rinsed in a mild dish soap and water solution. Wipe dry with a clean, soft cloth.
Never use steel wool or abrasive pads for cleaning. Never use chlorinated, citrus-based, or abrasive cleaners.
Stainless steel exterior panels have a clear coating that is stain resistant and easy to clean. Products containing abrasives will damage the coating and scratch the panels. Daily cleaning may be followed by an application of stainless steel cleaner which will eliminate water spotting and fingerprints. Early signs of stainless steel breakdown are small pits and cracks. If this has begun, clean thoroughly and start to apply stainless steel cleaners in an attempt to restore the steel.
Food Wells
The interior of the food wells should be cleaned daily with a non-abrasive cleaner and a non-abrasive pad. If necessary, a mild abrasive may be used on the interior of the pans only. Hard water stains and lime scaling may require a special cleaning product.

• Follow product instructions carefully if a sanitizer is used.
• Do not to leave cleaners in a food well overnight or for an extended period of time.
• Never use steel wool.
• Never use a high-pressure water wash for cleaning as water can damage the electrical components.

Drain
Each unit has a drain. Each drain can become loose or disconnected during normal use. Be sure all drain lines are free of obstructions.

GFCI Troubleshoot
Cabinet trips GFCI (ground fault circuit interrupter):
A GFCI receptacle protects against “ground faults” whenever an electrical product is plugged into the GFCI outlet. GFCI outlets or GFCI breakers constantly monitor the current flowing from a hot to a neutral. If the current leaving the receptacle is greater than what is returning, then this imbalance will cause the GFCI to trip in order to protect the user from electrical shock.
Heaters are prone to absorbing moisture into the heater themselves during long periods of not being used such as shipping or summer breaks. There are a couple of ways to resolve this
issue (GFCI tripping – Nuisance tripping is not covered under warranty)
Below is a way of resolving the GFCI tripping issue on units that are just being started up or have been sitting for a length of time:

1. Fill each Hot food well up with roughly 1.5” -2” of water (where applicable).
2. Flip the On/Off switch to the “On position” and turn the first [2] wells to the # 1 position. The orange light will appear for each well-lit.
3. Wait 5 minutes and turn the next [2] wells to the # 1 position. The orange light will appear for each well.
4. Wait another 10 minutes and rotate the dial to the # 2 position for all wells.
5. Wait another 10 minutes and rotate the dial to the # 3 position for all wells
6. Wait another 10 minutes and rotate the dial to the # 4 position for all wells.
7. Do NOT go beyond the # 4 position for 20+ minutes if even needed, as that is typically the tipping point.
8. If the breaker trips during the process, let the breaker sit for a few minutes and then reset it. Turn the dial back 1-2 positions and restart the process over

PAGE LEFT INTENTIONALLY BLANK

DELFIELD
980 SOUTH ISABELLA ROAD, MOUNT PLEASANT, MI 48858
800-733-8821
WWW.DELFIELD.COM

References

• Delfield - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>