homematic IP HmIPW-WRC6-A Wired Wall Mount Remote Control Instruction Manual
- June 13, 2024
- Homematic IP
Table of Contents
Wired Wall-mount Remote Control – 6 buttons,
anthracite
Installation and brief instructions
Proceed to the detailed manual
https://www.homematic-
ip.com/downloads/download/homematic_ip/bda/HmIPW-WRC6_UM_web.pdf
Device overview
A Mounting plate
B Clip-on frame
C Electronic unit
D Labelling field
F Button (channel 1-6) and LED (channel 7-13)
Installation
Please observe the safety instructions on the back side!
Mounting
A With supplied clip-on frame
B In (multi-gang) frame of other manufacturers
Connect device to:
A Central Control Unit
B Homematic IP Access Point (Cloud)
Teach-in HmIP device
Set-up system
Detailed manuals for…
| Wired System | Hematic IP App | Web UI Software |
|---|
https://www.homematic-ip.com/downloads/download/
handbuecher/HmIPW-Systemhandbuch.pdf| https://www
.homematic-ip.com/downloads/download/
handbuecher/Homematic_IP-Anwenderhandbuch.pdf|
https://www.homematic-ip.com/downloads/download/handbuecher/
WebUI_Handbuch_eQ-3.pdf
Function
This device is part of the Homematic IP smart home system and works with the
Homematic IP radio protocol. All devices of the Homematic IP system can be
configured comfortably and individually with the CCU3 user interface or
flexibly with the smartphone app in connection with the Homematic IP cloud.
The Homematic IP Wired Wall-mount Remote Control offers three pairs of freely
configurable buttons and can be used flexibly in the Homematic IP Wired system
to control devices and functions. At the push of a button it is possible to
switch lights on or off, raise or lower shutters or switch to
activate/deactivate the protection mode, for example.
A status LED is integrated next to each of the six buttons, which can light
up, flash or pulse in seven different colours. The LEDs can be used to
indicate a wide range of system states, such as the current protection mode,
lights switched on or open windows.
The wall-mount remote control is mounted to a free flush-mounted box using the
mounting plate. As an alternative to mounting with the supplied removable
frame, the remote control can be integrated into existing switch series from
other manufacturers. All current technical documents and updates are provided
at www.homematic-ip.com.
Installation instructions
Since the bus is powered by the Homematic IP Wired Access Point (HmIPW-DRAP),
you must first set-up a Homematic IP Wired Access Point (HmIPW-DRAP) to enable
power supply for the device. For further information, please refer to the
operating manual of the corresponding Wired Access Points.
Please note the insulation stripping length of the conductor to be connected,
indicated on the device.
Permitted cable cross sections for connecting to the device are: Rigid cable:
0.12-0.50 mm2
For reasons of electrical safety, only the following cables must be used for
connecting to the Homematic IP wired bus:
- Telephone cable J-Y(ST)Y with 2 x 2 x 0.8 (= 0.5 mm²) or 4 x 2 x 0.8 (= 0.5 mm²), shielded, TP
- Ethernet installation cable S/FUTP, Type Cat5e or higher with 2 x 2 x AWG22 (= 0.34 mm²) or 4 x 2 x AWG22 (= 0.34 mm²), shielded, TP
The shield (continuity wire) must be connected to “–” (=GND) at the bus connection of the Wired Access Point
(HmIPW-DRAP). The shield may not be connected to the device.
Please note! Only to be installed by persons with the relevant electro-
technical knowledge and experience!*
Incorrect installation can put your own life at risk and the lives of other
users of the electrical system. Incorrect installation also means that you are
running the risk of serious damage to property, e.g. because of a fire. You
may be personally liable in the event of injuries or damage to property.
Contact an electrical installer!
Technical specifications
Device short name
Supply voltage
Current consumption (max.)
Standby power consumption
Cable type and cross section
Installation
Degree of protection
Protection class
Ambient temperature
Dimensions (W x H x D)
Without frame
Including frame
Weight| HmIPW-WRC6-A
24 VDC, +5 % -20 %, SELV
40 mA
45 mW
Rigid cable, 0.12-0.50 mm²
only in normal commercial switch boxes (device boxes) in accordance with DIN
49073-1.
DIN 49073-1
IP20
III
-5 to +40 °C
71 x 71 x 40 mm
85 x 85 x 40 mm
68 g
---|---
Subject to technical changes
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>