LLOYTRON H1011 2400w Hair Dryer Instruction Manual
- June 13, 2024
- LLOYTRON
Table of Contents
H1011 2400w Hair Dryer
Instruction Manual
Travel Pro
Hairdryer
2400w
NOT FOR USE IN HOTELS, GUEST HOUSES ETC.
FOR HOUSEHOLD USE ONLY
MODEL: H1011
H1011 2400w Hair Dryer
thank you
Thank you for the purchase of this quality PAUL ANTHONY product. Used
carefully and in accordance with the instructions enclosed, it should give you
trouble free service over a long period of time. Please keep these
instructions for future reference.
FEATURES
- 3 Heat/ 2 Speed Settings
- Power: 2400w Max.
- Folding Function
- Narrow Concentrator Nozzle
- Safety Cut-Off
- Hang-Up Loop
- Quiet DC Motor
SPECIFICATIONS
- Operating Voltage: 220/240v AC 50/60Hz
- Power Consumption: 2400w max
- Ambient Operating Temperature: 5°C to 23°C
Note: Do not operate if ambient temperature is outside this range as this may damage the product.
IMPORTANT SAFEGUARDS AND PRECAUTIONS
SAVE THESE INSTRUCTIONS
- Read all instructions carefully
- For Household Use only.
- Not intended for commercial use.
- Only for use indoors.
DO NOT
Do not use outside or in damp conditions.
- Before plugging into mains socket, check whether supply line voltage and current rating are in compliance with the rated electrical parameters shown on the rating label.
- Keep away from hot surfaces, such as gas or electric hobs and ovens etc
DO NOT
Do not use for any purposes other than the appliances intended use.
DO NOT
Do not use if any part of this appliance is damaged in any way.
- This product is not intended to be operated by means of an external timer or separate remote control system.
- To prevent damage to the power cord, do not let it pass over sharp corners, edges or hot surfaces.
- If the power cord is damaged, do not use. Check before each use!
The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
- Always unplug when not in use.
- To prevent against the risk of electric shock, do not submerge any part of this appliance in water, unless advised in this manual.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with this appliance.
- Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.
WARNING! Do not use this appliance near bathtubs, showers or other vessels containing water.
- When the appliance is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the appliance is switched off.
- For additional protection, the installation of a residual current device (RCD) having a rated residual operating current of 30mA is advisable in the electric circuit supplying the bathroom. Ask your installer for advice.
WARNING
- Keep the appliance and its cord out of reach of children less than 8 years.
- Should this appliance fall into water, pull the plug out of the wall immediately. Do not place your hand in the water. The appliance should then be checked by a qualified electrician before use again!
- The air inlet and outlet openings should never be obstructed.
- Keep your hair away from the immediate vicinity of the air inlet opening.
- The safety grill fitted in the air inlet opening is designed to prevent hair being drawn in. If the grill becomes clogged, it should be cleaned (e.g. with vacuum cleaner or brush), as otherwise the airflow will be obstructed to such an extent that the thermal cut-out will operate.
DO NOT
Do not touch the scalp when using.
DO NOT
Do not allow the supply cord to come in contact with the heating element
during use.
DO NOT
Do not direct aerosols or water sprays into the appliance.
DO NOT
Do not use the hair dryer with wet hands or wet hair.
- When drying your hair in rollers, do not allow any clips, hairpins etc. to project more than 10mm (finger width) so as to ensure that they do not come in contact with the live parts inside the appliance.
- When using clips and hairpins, these may become hot with prolonged drying. It is advised that these are removed.
WARNING – SPECIAL SAFETY CUT OUT DEVICE
This hairdryer is fitted with a special thermal cut-out safety device.
If the product overheats due to a fault then the power will be removed from
the device and the unit will stop working.
First you should check the unit to find the cause of the fault, or take to an
engineer.
Check the fan is operating at full speed and the air inlet is not blocked.
Do not use the hairdryer if fault cannot be resolved.
The safety device is designed so that it will only reset if unplugged for more
than 2 minutes.
LOCATION OF CONTROLS
A- Speed Switch
This switch is used to operate the unit. Switch between off, low and high
speeds to operate the fan motor at different speeds dependent upon the hair
style requirements.
B-2 Heat Switch
During operation, switch between low, medium and high heat settings to change
the temperature of the air being output via the fan motor.
C- Folding Function
The folding function makes for easy storage and makes it perfect for travel.
D– Concentrator Nozzle Attachment
The removable concentrator nozzle attachment helps to focus the hot air to a
more concentrated target of hair.
E– Hanging Loop
The hanging loop allows for easier storage.
F — Cool Shot Button
During use, press and hold the cool shot button to change the output air
temperature from hot to cold. Once the cool shot is released, the output air
temperature will revert back to the temperature set by the heat switch.
OPERATION
■ BASIC DRYING
- GENTLY towel dry hair to REMOVE any excess water. AVOID rubbing hair too vigorously as this could cause split ends to form. USE a wide toothed comb to detangle hair.
- PLUG the power cord into a suitable mains supply, ensuring that the speed & heat setting switches are set TO’0′
- BEGIN drying hair by SETTING the speed/ heat switch to 1 increase depending on hair type. USE your fingers to ‘COMB’ through and DIVIDE hair to help dry more effectively.
- When hair is almost dry all over, SET both the speed and heat switches to the LOWEST setting based on desired styling.
- DIVIDE hair into manageable sections and BEGIN brushing from the nape of the neck towards the scalp, followed very closely by the dryer as you work your way through the hair. CONTINUE this process in SMALL sections at a time.
Recommended Settings
Hair Type| Airflow/Heat
Short & Curly| 1
Short & Sculptured| 1
Medium & Curly| 1
Medium & Sleek| 3
Medium & Sculptured| 2
Long & Curly| 1
Long & Sleek| 2
Long & Sculptured| 3
■ CONCENTRATOR NOZZLE ATTACHMENT
The removable concentrator nozzle attachment helps to focus the hot air to a
more concentrated target of hair.
■ STRAIGHT, SMOOTH HAIR STYLING
- BEFORE operating the hairdryer, ATTACH the concentrator nozzle attachment to the hairdryer, ENSURING that it clips into place SECURELY.
- USING a large, round brush, BRUSH the hair from underneath.
- PULL the hair down until the hair is fully extended and taut.
- SET the speed switch and heat switch to the HIGHEST settings and RUN the hairdryer SLOWLY up and down the length of the hair SEVERAL TIMES until it is dry.
- REPEAT this process with all sections of hair until it is completely dry all over.
■ CURLY HAIR
- SET the heat switch and speed switch to the LOWEST setting and MOVE the hairdryer quickly around your head.
- As the hair is drying, SCRUNCH it using your preferred styling product or TWIRL strands of hair around your fingers to add definition.
■ COOL SHOT
A touch of the cool shot button instantly produces cold air for setting hair
and also for professional styling. Use the cool shot as a finishing touch to
hold and set your new style.
CLEANING AND CARE
■ MAINTENANCE
The Hair Dryer is virtually maintenance-free. Keep all vents and openings
clear of dirt and dust. If cleaning becomes necessary, disconnect the unit
from the power source, ensure it has cooled completely and wipe the exterior
with a damp cloth, then wipe dry.
If any abnormal condition occurs, unplug the unit, allow it to cool and return
it for repair to an authorized service representative only. Repairs should not
be attempted by the user.
- Always disconnect the hair dryer before cleaning.
- Never immerse the hair dryer in water.
- It is sufficient to wipe the exterior over with a damp cloth and then wipe dry.
- A soft dry brush may be used to remove dust and hairs from the air inlet grille, to ensure proper airflow at all times.
WARNING
To avoid the risk of electrocution — KEEP AWAY FROM WATER HAZARDS
- **** DO NOT IMMERSE THE UNIT IN WATER OR ANY OTHER LIQUID
- DO NOT TAKE OR USE THIS APPLIANCE IN THE BATHROOM
- DO NOT USE A HAIR DRYER WITH WET HANDS
- NEVER USE THE HAIR DRYER IN THE BATH, UNDER A SHOWER OR OVER A WASH BASIN FULL OF WATER
- DO NOT REACH FOR THE HAIR DRYER IF IT HAS FALLEN INTO WATER OR ANY OTHER LIQUID. UNPLUG IT IMMEDIATELY.
■ STORAGE
When not in use, store the Hair Dryer out of reach of children in a safe, dry
location. Do not jerk or strain cord at plug connections. Do not wrap the line
cord around the appliance. Allow the cord to hang or lie loose and straight at
the point of entry into the appliance.
Only store the product in environments ranging from 5°C to 23°C ambient
temperature. Failure to comply could result in damage to the product.
WEEE/ENVIRONMENTAL PROTECTION
■ DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT
Do not dispose of this product with household waste. For the proper treatment,
recovery and recycling please take this product to the appropriate waste
collection point. If you are unsure where this may be, please contact your
local authority. Improper disposal may be harmful to the environment.
UK PLUG REWIRING
Your appliance operates on 220-240V-50Hz AC Mains and comes fitted with a 3-pin BSI Approved plug, so that it is ready for use by simply plugging into AC Mains. Should you need to change or refit a plug, proceed as follows:
■ IMPORTANT:
The wires in the mains lead are coloured in accordance with the following
code:
BLUE: NEUTRAL(N)
BROWN: LIVE (L)
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
The BLUE wire must be connected to the terminal which is marked with the
letter “N” or coloured BLACK. The BROWN wire must be connected to the terminal
which is marked with the letter “L” or coloured RED.
■ DO NOT CONNECT EITHER WIRE ‘L’ OR ‘N’ TO THE EARTH TERMINAL OF A 3-PIN
PLUG
Always ensure that the Mains Cord is located into the Plug through the Cord
Guard or Cable Clamp, and that the Cord Guard screws are tightened to clamp
the Cord (outer sheath and inner coloured wires) in position in the Plug. Make
sure the Plug top is also fitted securely.
The supply cord cannot be replaced. If the supply cord is damaged, the
appliance should be scrapped.
This appliance must be protected by a 13 Amp fuse in a 13Amp type (BS1363)
plug. Should you need to replace the fuse, use only an ASTA approved BS1362
fuse.
CUSTOMER SERVICES
If you have any queries about this product then please contact Lutron Customer
Services online at:
www.lloytronhelpdesk.com
To find out more about Paul Anthony products, visit
www.lloytron.com Distributed in UK by Lutron Ltd,
Laltex House, Leigh, England WN7 3XH
Distributed in Europe by Laltex Ireland Ltd, Dublin 2, D02 AY86