LIEBHERR XCCsd 5250 Prime American Fridge Freezer Installation Guide

LIEBHERR XCCsd 5250 Prime American Fridge Freezer Installation Guide

General safety instructions

The manufacturer is continually working on the further development of all types and models. Please be aware that we reserve the right to make changes to the shape, equipment and technology.

1. General safety instructions

• Please keep this assembly manual in a safe place so you can refer back to it at any time.
• If you pass the appliance on, please hand this assembly manual to the next user.
• Read this assembly manual carefully before installation and use to ensure safe and correct use of the appliance. Follow the instructions, safety instructions and warning messages included at all times. They are important for ensuring you can operate and install the appliance safely and without any problems.
• First read the general safety instructions in the “General safety instructions” section of the operating instructions, which accompany these installation instructions, and follow them. If you cannot find the operating instructions, you can download the operating instructions from the internet by entering the service number at home.liebherr.com/fridge-manuals. The service number can be found on the serial tag:
• Observe the warning messages and other detailed information in the other sections when installing the appliance:

2. Installation dimensions

3. Transporting the device

• Transport the appliance in its packaging.
• Transport the appliance upright.
• Use two people to transport the appliance.

4. Side by side assembly

Set up the freezer or the appliance with the freezer compartment from the left when viewed from the front. These appliances are equipped with a side-wall heater on the right hand side to prevent condensation forming.

All the assembly components are supplied with the appliance.

Assembly parts in the accessory kit

Ensure that the following tools are to hand:

• Size 10 open-ended spanner (supplied)
• Torx® 25/20/15 screwdriver
• Cordless screwdriver
• Spirit level

Information on moving the SBS combination:

• Set up the appliances as close to the final position as possible before assembly.
  The appliances must be accessible on all sides for correct assembly.

• When moving the appliances after assembly, always take hold from the front outer corners. Never press your knee against the side walls or door.

• The SBS combination can be moved most easily when moved diagonally, that is by alternately pushing from the left and right corners.

If the combination is standing directly in front of the recess, push it in straight.

NOTICE
Risk of damage when moving the combined SBS appliance!
The combined SBS appliance is heavy once assembled. The appliance may be dented by improper movement.

• Observe the information given on moving the appliance (see above).
• Take off all protective film from the exterior of the appliance.

Bottom front of the appliance:

Fig. 10

• Tighten the outer adjusting feet. The appliances can be moved easier.
• Push both appliances to approx. 10 mm of each other so that they are positioned flush facing forwards.
• Straighten the appliances up using a spirit level on the top of the appliance.

Top front of the appliance:

Fig. 11

• Remove the existing covers.

• Before fitting the top bracket remove both earthing screws
  Fig. 11 (14) .

• Store the earthing screws safely. The screws will be necessary for fitting the bracket as shown below.

Fig. 12 Example illustration

• Slide the bracket Fig. 12 (3) onto the pins with the spacer between the appliances. Loosely screw in the brackets alternately right and left with four screws Fig. 12 (4) and the previously removed earthing screws Fig. 12 (14) .
• If necessary: Check the appliance is stood straight by laying a spirit level on the top of the appliance.

Bottom front of the appliance:

• Remove the existing covers.

Fig. 13

• If the metal plate Fig. 13 (1) is installed, unscrew the metal plate.

Note
If you want to transport the appliance or set it up as an individual appliance, you must re-attach the metal plate.

Fig. 14 Example illustration

• Slide the bracket Fig. 14 (6) on with the spacer between the appliances and screw in loosely with the 4 screws
  Fig. 14 (4) .

• If necessary: Set up the appliances so that they are level.

• Tighten the screws firmly at the top and bottom.

Top rear of the appliance:

Fig. 15 Example illustration

• Slide the bracket Fig. 15 (7) onto the appliance ceiling with the lugs and with the spacer between the appliances. Screw in firmly with 2 screws Fig. 15 (5) .

Bottom rear of the appliance:

Fig. 16 Example illustration

• Slide the bracket Fig. 16 (8) on with the slots over the retainer for the wall spacers.

Note
Holes for the screws must be pre-drilled.

Side by side assembly

• Mark the position of the holes to be drilled with a pencil.
• Remove the bracket again.

Fig. 17

Note
Only drill through the metal plate. Drilling depth approx. 1 mm.

• Pre-drill the screw holes with a 3 mm drill and deburr.

Fig. 18 Example illustration

• Slide the bracket Fig. 18 (8) on once more with the slots over the retainer for the wall spacers.
• Screw in tightly with the 2 screws Fig. 18 (5) .

Before fitting the top and front cover strips, push the two bars together over the whole length. The strips can be inserted more easily into the gap. Use a soft cloth to push the strips in to avoid dents in the surface of the cover strips. Press the strips into the gap carefully and evenly in order to achieve an optimum bond.

For appliances with lever handle

Fig. 19

• On the top press the short cover strip Fig. 19 (9) into the horizontal gap.

For appliances with recessed grip

Fig. 20

 On the top press the short cover strip Fig. 20 (9) into the horizontal gap.

For appliances with lever handle

Fig. 21

• On the front, press the long cover strip Fig. 21 (10) into the vertical gap. Ensure that the strip rests on the connecting plate.

For appliances with recessed grip

Fig. 22

• On the front, press the long cover strip Fig. 22 (10) into the vertical gap. Ensure that the strip rests on the connecting plate.
• Take off the protective film from the cover strip.*

Top front of the appliance:

Fig. 23 Example illustration

• Snap the top cover Fig. 23 (11) onto the still open gap between the two control panel trims. Make sure that the outer sides of the cover form a flush finish with the control panel trims.

Bottom front of the appliance

Fig. 24 Example illustration

• Place the bottom cover Fig. 24 (12) onto the bracket from the front Fig. 24 (1) , slide it down Fig. 24 (2) and snap it in at the bottom Fig. 24 (3) .

• To disassemble the cover, insert a screwdriver at the bottom on the side below the cover and release both lower hooks.
  The cover can swing out upwards.

• Connect the combination electrically. See the installation guide.
  Appliances with Ice Maker:

• Connect the appliance to the fixed water connection. See the installation guide.

NOTICE
Risk of damage when moving the combined SBS appliance!
The combined SBS appliance is heavy once assembled. The appliance may be dented by improper movement.

• Observe the information given on moving the appliance (see above).
• Carefully push the SBS combination into the specified position.
• If necessary, align the SBS combination using the levelling feet.
• Then prop up the door: Lower outer adjusting feet on the bearing bracket until they are resting on the floor.

The doors can be straightened at height on the outer lower bearing brackets:

• Open door to 90 °.

Fig. 25

• To lift the door, unscrew the adjusting foot Fig. 25 (18) clockwise using the supplied open-ended spanner Fig. 25 (2) until the foot makes contact with the floor. Then continue turning until the door is adjusted to the right height. When delivered, the bearing pin is completely screwed in.

Fit decorative base trim.
After you have assembled and straightened out the appliances, the base trims can be fitted at the bottom of the appliances.
The base trims are decorative and will not affect the functionality of the appliances.

For appliances with bottom soft stop mechanism

Fig. 26

• Secure the base trim recess at the bottom of the appliance, as shown in the figure.

Note
The trim must be pushed to a little behind the bearing bracket cover.

For appliances without bottom soft stop mechanism

Fig. 27

• Secure the base trim recess at the bottom of the appliance, as shown in the figure.

home.liebherr.com/fridge-manual

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>