TATYBO WT3 Wireless Gaming Headset with USB Dongle User Manual

June 13, 2024
TATYBO

TATYBO WT3 Wireless Gaming Headset with USB Dongle User Manual
TATYBO WT3 Wireless Gaming Headset with USB Dongle

Use of Line-in cable

Use of Line-in cable

Product description

Product description

  1. 2.4G key
  2. On/Off button
  3. Virtual 7.1/Effect Light
  4. Microphone mute
  5. Increase/decrease volume
  6. Paired lights
  7. LINE IN interface
  8. External microphone
  9. Status effect light
  10. Charging indicator light
  11. Type-C interface

Connecting

Connecting

Product parameter

Horn diameter 50 mm Transmission distance ≤10 meters,360degrees
Speaker impedance 20Ω Operating Voltage 3.7V    __
Battery capacity 1000mAh Charging voltage DC5V  1A
Battery Type Polymer lithium battery Microphone sensitivity -42±3dB
Charging time ≤2.5 hours Microphone indicative Omnidirectional
Battery life ≥30 hours Low latency <25MS

Transmitter parameters

Working voltage 5V Transmitting power 7.5 dBm
Working current 30mA Transmission distance ≤10M, 360°
Frequency range 2.402GHz-2.480GHz Receiving sensitivity -92dBm
Bandwidth 950 KHz

launcher

Device plug: compatible with laptop/PC/PS4/PS5/TV/Switch

a) When using, plug in the computer’s A-end USB interface or B-end Type-C interface for plug and play wireless connection.
A.

  1. The transmitter is plugged into the USB port on the A end of the computer or the Type-C end of the phone, laptop, etc. It will automatically connect without the need for the user to install drivers and run additional software.

B.

  1. After inserting the transmitter into the USB interface on the A terminal of the computer, the green indicator light of the transmitter flashes at this time, and the green light remains on after the headset is turned on and the code is checked. On the computer, you can view the icon in the lower right corner of the device that displays “TATYBO WT3”, indicating that the wireless headset device has been successfully installed. “On first use, open the ‘Audio’ bar of the ‘Sounds and Audio Device Properties’ of this device and set it to the default.”.
  2. Insert the B-terminal Type-C transmitter into the phone or laptop with the Type-C interface, and automatically turn on the pairing mode. The green light flashes quickly, and the green light remains on after the code is matched. The B-terminal Type-C transmitter is inserted into the phone interface, and the green indicator of the transmitter flashes. The wireless headset is turned on, and the green light remains on after the code is matched. This indicates that the plug and play wireless connection device has been successfully installed.

How to re-pair when unable to connect with your device.

  1. After the transmitter is inserted into the device, follow the steps b1 and b2 above to connect.
  2. Pairing operation between transmitter and earphone: Press and hold the power button+7.1 button for 5 seconds to pair again. The pairing sound “Pairing” flashes quickly, and then insert the USB dongle to connect successfully. The green light remains on.

Line-in connection line use

  1. Device side plug: compatible with PC (32-bit/64bit)/PS4/PS5/XBOX LINE IN mode/Ninto Switch/ Android/iOS mobile devices/devices with 3.5 audio interface
  2. Instructions for using the Line-in interface: Plug in the Line-in cable to shut down the wireless device, turn off the headset effect light, and enter the wired headset mode
  3. External microphone use: Insert to enable the external microphone, and unplug to disable the microphone.
Button Function Operate Step
2.4Gswitching key 2.4G mode Move down/up
  1. Move down to 2.4G mode, with a green light indicating “Gameplay mode”.

| Virtual 7.1/ Effect Light Switch| Click/Double Click|

  1. Turn on the default music mode for the headphones, click to turn on virtual 7.1 mode, and then click to turn on music mode.
  2. The earphones default to displaying the effect light. Double click on the effect light to turn it off, and then double click on the effect light to turn it on.

| Mi Mute Mode| Click|

  1. In headphone call mode, click on the “talk mic unmute” button to activate the “talk mic unmute” button, and then click on the “talk mic mute” button to activate the “talk mic mute” button.

| On/Off Key/ Pause/Playe| Long press for 2 seconds/ Click|

  1. Press and hold the power button for 2 seconds in the shutdown state to hear the “power on” effect light constantly on and the pairing light flashes quickly. Press and hold the power button for 2 seconds in the startup state to hear the “power off” effect light turn off and the pairing light turns off.
  2. In music playback mode, click the power button to pause.
  3. In music playback mode, click the power button to play.

2.4Gpairing mode| Long press for 5 seconds|

  1. In the shutdown state, press and hold the power button+7.1 button for 5 seconds to re-enter pairing mode The ‘Pairing’ pairing light flashes quickly.

Answer/hang up/reject| Click/Double Click|

  1. Click the power button to answer a incoming call,
  2. Click the power button to hang up during the call, and
  3. In call mode, double-click the headset to reject the incoming call.

Connect/ Disconnect| /|

  1. The “Connected” pairing light is constantly on when connecting the headphones to the phone.
  2. Connect the headphones to the phone Connect it, then turn off the Bluetooth mode prompt tone of the phone, and the “Distincted” pairing light will flash quickly.

| Increase/ decrease volume| Slide up/down|

  1. Slide up to increase the volume until the maximum prompt tone is “beep” (no interruption during playback, no”
  2. Slide down to decrease the volume to the minimum beep sound.

LINE INmode| External 3.5 audio cable| Inserting a 3.5 audio cable|

  1. In the power on state, insert a 3.5 audio cable, reset the power off, use wired headphones, and a prompt tone“power off”。

| Type-C char ging| Insert chargin g cable|

  1. Charging current: 500mA, red light on for long charging, green light on when fully charged

Answers to questions

  1. What about the distortion or jamming of the wireless headset?
    Answer:

  2. Check the source of music,

  3. Disconnect other devices,

  4. Re-plug the transmitter and pair it

  5. Play multiple players on the PC and the jamming operation fails, but the headset function is normal?
    Answer:

  6. Check the playback decoder,

  7. Turn off multiple players in the background,

  8. Check whether there is any obstacle between the headset and the PC terminal that will affect the signal transmission between them.

*When playing music in 2.4G mode and the battery voltage is lower than 3.2V, there is a low battery prompt. The prompt sounds “Low Battery” every 1 minute, and the red light flashes quickly.
When the battery voltage is lower than 3.1V, the system automatically shuts down with a prompt sound of “power off”.
The headset low battery prompt indicates that you are ready to use the headset after it is fully charged.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals