StarTech Com SECTBLTPOS2 10.2” to 10.5” Secure iPad Enclosure with Surface Mount User Manual

StarTech Com SECTBLTPOS2 10.2” to 10.5” Secure iPad Enclosure with

Surface Mount

Compliance Statements

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders. PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. Apple and iPad are trademarks of Apple Inc., registered in the U.S. and other countries and regions.

Safety Statements

Safety Measures
Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.

Warning Statements

• Assemble this product according to the instructions.
• Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product.
• This product is intended for indoor use only and should not be used outdoors.
• Do not over-tighten the screws. If any resistance is encountered, stop tightening.
• Pinch hazard! Keep your fingers clear from moving components.

Product Diagram

Front View

Product Dimensions

Note : All measurements are in millimeters.

Front View
Rear View
Bottom View
Edge View
Side View

Product Information

Requirements
For the latest manuals, product information, technical specifications, and Declarations of Conformance, please visit: www.StarTech.com/SECTBLTPOS2

• Phillips Head Screwdriver
•  Electric Drill
• Pencil

Package Contents

Note: The following images are not to scale.

Installation

Note : Do not overtighten any of the screws.
Pinch hazards! Keep hands away from any pinch points created by the mechanical components. Failure to do so may result in serious personal injury.

Add the iPad to the Tablet Enclosure Assembly Unlock the Tablet Enclosure Assembly

1.  Insert the Key into the Lock, located on the side of the Tablet Enclosure Assembly, and turn counterclockwise to unlock. (Figure 1)
2.  Remove the Front Plate from the Rear Plate.

Add the Felt Tape to the Front Plate

1.  Remove the Adhesive Backing from the 200 x 5 mm Felt Tape (x 2) and affix to the long edges of the inside of the Display Frame, located on the Front Plate. (Figure 2)
2. . Remove the Adhesive Backing from the 150 x 10 mm Felt Tape (x 2) and affix to the short edges of the inside of the Display Frame, located on the Front Plate.

Add the Foam Blocks to the Rear Plate

20 x 15 mm x 3 mm

1.  Remove the Adhesive Backing from the 20 x 15 x 3 mm EVA Pads (x 4) and affix to the inside edge of the Tabs (x 4), located on the inside of the Rear Plate. (Figure 3)
2.  (Optional) Remove the Adhesive Backing from the 100 x 25 x 20 mm Foam Blocks (x 2) and affix next to the Tabs, towards the center of the Rear Plate.
3.  (Optional) Remove the Adhesive Backing from the 100 x 15 x 12 mm Foam Blocks (x 2) and affix along the inside edge on the top and bottom of the Rear Plate. (Figure 4)

Insert the iPad into the Tablet Enclosure Assembly

1. Insert the Power/Data Cable through one of the openings, located in the rear/sides of the Rear Plate, and into the iPad.(Figure 5)
2.  Place the iPad into the Tablet Enclosure Assembly, routing the Power/Data Cable around the EVA Pads. Ensure the Power/Data Cable is routed without any sharp bends.
3.  Attach the Front Plate to the Rear Plate and Lock the Tablet Enclosure Assembly, using the Key. (Figure 6)

Mounting the Angled Bracket

Remove the Adhesive Backing from the Rubber Pads (x 4) and affix to the base of the Angled Bracket. (Figure 7)

Mounting Option #1 – Tabletop- Fixed

1. Place the Angled Bracket in the intended mounting location, on a Tabletop.
2.  Mark the location of the Screw Holes (x 3), using a Pencil.
3.  Remove the Angled Bracket and drill appropriately sized Pilot Holes (x 3) to an appropriate depth in the Tabletop, using an Electric Drill.
4.  Thread the Small Washers (x 3) over the 5 x 20 mm Self Tapping Screws (x 3) to complete the Screw Assemblies.
5.  Align the mounting holes, located on the Angled Bracket, with the Pilot Holes, located in the Tabletop.
6.  Insert the Screw Assemblies (x 3) through the Angled Bracket and into the Tabletop and tighten, using a Phillips Head Screwdriver. (Figure 8)

Mounting Option #2 – Tabletop – Rotating

1.  Place the Angled Bracket onto the intended mounting location, on a Tabletop.
2.  Mark the location of the Screw Hole, located closest to the front of the Angled Bracket, using a Pencil.
3.  Remove the Angled Bracket and drill an appropriately sized Pilot Hole in the Tabletop, using an Electric Drill.
4.  Thread a Small Washer over a 5 x 20 mm Self Tapping Screw to complete the Screw Assembly.
5.  Align the Large Washers (x 2) over the Pilot Hole. (Figure 9)
6.  Align the hole, located towards the front of the Angled Bracket, with the hole, located in the Large Washers.
7.  Insert the Screw Assembly through the Angled Bracket, the Large Washers, and into the Tabletop and partially tighten, using a Phillips Head Screwdriver.
8.  Adjust the tension of the Screw Assembly to adjust the ease of rotation.

Mounting Option #3 – Wall Mount

1.  Place the Angled Bracket onto the intended mounting location, on a Wall.
2. . Mark the location of the Screw Holes (x 3), using a Pencil.
3.  Remove the Angled Bracket and drill appropriately sized Pilot Holes (x 3) in the Wall, using an Electric Drill.
4.  Thread the Small Washers (x 3) over the 5 x 20 mm Self Tapping Screws (x 3) to complete the Screw Assemblies.
5.  Align the Angled Bracket with Pilot Holes, located in the Wall.
6.  Insert the Screw Assemblies (x 3) through the Angled Bracket and into the Wall and tighten, using a Phillips Head Screwdriver. (Figure 10)

Attach the Tablet Enclosure Assembly to the Angled Bracket

1.  Align the holes, located on the Rear Plate of the Tablet Enclosure Assembly, with the holes, located in the Angled Bracket.
2.  Insert the M4 x 8 mm Screws (x 4) through the Angled Bracket and into the rear of the Tablet Enclosure Assembly and tighten, using the M2.5 Hex Key.
3.  Attach the Power/Data Cable to an available Power Source.

Warranty Information

This product is backed by a five-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find th parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.

Reviews
Share your experiences using StarTech.com products, including product applications and setup, what you love about the products, and areas for improvement.

StarTech.com Ltd.

45 Artisans Crescent London, Ontario N5V 5E9

• Canada
  

• 4490 South

• Hamilton Road

• Groveport, Ohio

• 43125

• U.S.A.

• Unit B, Pinnacle 15

• Gowerton Road

• Brackmills,

• Northampton

• NN4 7BW

• United Kingdom

• Siriusdreef 17-27

• 2132 WT

• Hoofddorp

• The Netherlands

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

References

• Secure Tablet Stand, up to 10.5in - Tablet Mounts

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>