Klipsch CINEMA 201 ASB201 Dolby Sound Bar User Manual

CINEMA 201 ASB201 Dolby Sound Bar
User Manual

INSIDE

SOUND BAR

CONNECTIONS – HDMI-ARC

(IF TV HAS NO HDMI-ARC OUT SEE CONNECTIONS – DIGITAL OPTICAL)

A Basic TV HDMI input will not transfer the TV audio signal to the Sound Bar. The Cinema One Sound Bar will only receive TV audio through HDMI-ARC (with CEC turned ON), Optical or Analog connection.

TURN OFF TV SPEAKERS

CONNECTIONS – DIGITAL OPTICAL

(IF TV HAS NO OPTICAL OUT SEE NEXT PAGE)

CABLE NOT INCLUDED

CONNECTIONS – 3.5mm AUXILIARY

CABLE NOT INCLUDED

REMOTE

• On / Off
• LEDs On/Off (Sound Bar)
• System Volume Up
• System Volume Down
• Subwoofer Level Up
• Subwoofer Level Down
• Mute
• Bluetooth ® Source Select
• Source Select
• Virtual Surround Mode On/Off
• Dialog Enhance Mode On/Off
• Night Mode On/Off

SURROUND MODES

| ((SUR))
VIRTUAL SURROUND MODE| DIALOG
DIALOG ENHANCE MODE| NIGHT
NIGHT MODE
---|---|---|---
•Only active if receiving a| •Klipsch Custom DSP| •Optimizes E0 for Dialog| •Reduces Dynamic Range
Dolby Digital signal| •Independent of the EQ settings| •Can be ON regardless of Dolby Status or| •Subwoofer OFF
•Manufactured under| (Natural, Voice, Night)| Virtual Surround Mode| •Can be ON regardless of Dolby Status or
license from Dolby Lab-| •Can be ON regardless of Dolby Digital status| •Only one EQ profile active at one time| Virtual Surround Mode
oratories. Dolby, Dolby| | (Natural, Dialog Enhanced, or Night)| •Only one E0 profile active at one time
Audio and the double-D symbol are trademarks of Dolby Laboratories| | | (Natural, Voice Enhanced, or Night)
| MODE AMBIOPHONIOUE VIRTUEL| MODE D’EGALISATION D’ACCENTUATION VOCALE| MODE NOCTURNE
•Actif seulement avec reception Tun signal Dolby Digital| | |
| MODALIDAD DE SURROUND VIRTUAL| MODALIDAD DE ECUALIZACION DE| MODALIDAD NOCTURNA
•Activa solo cuando hay senal Dolby Digital| MEJORAMIENTO DE VOZ| |

BLUETOOTH WIRELESS TECHNOLOGY

PAIR

Hold 3 Seconds

|
---|---
| |
---|---|---

• Example only. Your device may differ.

RECONNECT

TV REMOTE PROGRAMMING

If you want to use the TV remote to control the sound bar, you can program the sound bar to take commands from your TV remote

1. Hold 3 Seconds
2. Source Flashes
3. Press x1 to Program
4. Source Turns Off
5. Press Volume Up x1
6. Source Flashes x3 and Turns Solid

To program Volume Down button repeat the steps shown and replace steps 3 and 5 with the button you want to program.

REMOTE CONTROL CODES

(FOR UNIVERSAL OR CABLE REMOTES)

HEX CODES – SET 1

VOLUME UP| Ox 856A 9F60
VOLUME DOWN| Ox 856A 9E61
MUTE| Ox 856A 9966
HEX CODES – SET 3

VOLUME UP| Ox A55A OAF5
VOLUME DOWN| Ox A55A OBF4
MUTE| Ox A55A 12ED
HEX CODES – SET 4

VOLUME UP| Ox 859A 817E
VOLUME DOWN| Ox 859A 827D
MUTE| Ox 859A 8778

• MUST HAVE AUDIO/AUX BUTTON OR AUDIO·SB BUTTON
  RED CENTER BUTTON
  NOTE** : NOT ALL UNIVERSAL REMOTES ARE COMPATIBLE

LED ON/OFF

• Press x1
• BRIGHT
• ALWAYS ON
• DIM
• OFF AFTER INACTIVITY

FACTORY RESET

Clears Bluetooth ® pairing history and user programmed IR commands
Hold 10 Seconds

CARE AND CLEANING

| “The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Klipsch Group, Inc. is under license. Other trademarks and trade names are those of their respective owners.”
---|---
| Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the doube-D symbol are registered trademarks of Dolby Laboratories.
| HDMI, High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing, Administrator in the United Staed and/or other countries.

MPORTANT SAFETY INSTRUCTIONS!

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are  rovided for your safety.
   If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE ONLY with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle.

17. The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable.

18. DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or fire.

19. The equipment shall be used at maximum 113˚F / 45˚C ambient temperature.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons.
WARNING : To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.
WARNING : To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instruction.
WARNING : No naked flame sources – such as candles – should be placed on the product.
WARNING : This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
THIS PRODUCT CONTAINS A LITHIUM COIN CELL BATTERY . IF MISUSED OR ABUSED THIS CAN RESULT IN:

• Smoke or gas hazard
• Heat hazard
• Fire hazard
• Explosion hazard

WARNING : Do not place batteries in mouth or ingest. Chemical burn hazard. Keep new and used batteries out of reach of children and pets. If swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
WARNING: If battery compartment does not close securely, stop using the product and keep it away from children and pets.
WARNING: Do not handle leaking or damaged Lithium batteries.
WARNING: Risk of leakage. Only use the specified type of batteries. Never mix new and used batteries.
Observe correct polarity. Remove batteries from products that are not in use for extended periods of time. Store batteries in a dry place.
WARNING: Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
WARNING: Do not recharge non-rechargeable batteries.
WARNING: Avoid exposure to extreme heat or cold.
Please dispose of any used batteries properly, following any local regulations. Do not incinerate.

WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel.
Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch.
WARNING: This product is intended to be operated ONLY from the AC Voltages listed on the back panel or included power supply of the product. Operation from other voltages other than those indicated may cause irreversible damage to the product and void the products warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power cord, use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2014/35/EU; European Union EMC Directive 2014/30/EU; European Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EU; European Union WEEE Directive 2012/19/EU; European Union

Eco-Design Directive 2009/125/EC; European Union Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) Directive 2006/121/EC; European Union Radio Equipment Directive (RED) 2014/53/EU.
This product contains batteries that are covered under the 2006/66/EC European Directive, which cannot be disposed of with normal household waste. Please follow local regulations.
You may obtain a free copy of the Declaration of Conformity by contacting your dealer, distributor, or Klipsch Group, Inc.’s worldwide headquarters. Contact information can be found here: http://www.klipsch.com/Contact-Us

WEEE NOTICE
Note : This mark applies only to countries within the European Union (EU) and Norway.
This appliance is labeled in accordance with European Directive 2012/19/EU concerningwaste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an
appropriate facility to enable recovery and recycling.

FCC AND CANADA EMC COMPLIANCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  nstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.
• Consult the dealer or an experienced radio/TV technician for help.

Approved under the verification provision of FCC Part 15 as a Class B Digital Device.
Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this device.
Caution: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC
Rules, this device is to comply with Class B limits. All peripherals must be shielded and grounded.Operation with non-certified peripherals or non-shielded cables my result in interference to radio or reception.
WIRELESS TRANSMITTER COMPLIANCE INFORMATION
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Slave Equipment: (for play-fi module 2.4G and 5GHz dual bands)
This device is slave equipment, the device is not radar detection and not ad- hoc operation in the DFS band.
Industry Canada statement:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Caution:(for play-fi module 2.4G and 5GHz dual bands)
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.
(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

RSB-3
FIRMWARE VERSION 1.4
Bluetooth Operating Frequency: 2402-2480MHz
Maximum RF Power: 10 dBm (e.i.r.p)
RSB-6
Bluetooth Operating Frequency: 2402-2480MHz
Maximum RF Power: 4 dBm (e.i.r.p)
RSB-8
Bluetooth Operating Frequency: 2402-2480MHz
Maximum RF Power: 4 dBm (e.i.r.p)
RSB-11
Bluetooth Operating Frequency: 2402-2480MHz
Maximum RF Power: 10 dBm (e.i.r.p)
Wireless Tx & Rx Operating Frequency: 2405.35-2477.35MHz
Maximum RF Power: 10 dBm (e.i.r.p)
RSB-14
Bluetooth Operating Frequency: 2402-2480MHz
Maximum RF Power: 10 dBm (e.i.r.p)
Wireless Tx & Rx Operating Frequency: 2405.35-2477.35MHz
Maximum RF Power: 10 dBm (e.i.r.p)
Wi-Fi Operating Frequency: 2412-2472 MHz
Maximum RF Power: 20 dBm (e.i.r.p)
Wi-Fi Operating Frequency: 5150-5350MHz & 5470-5725MHz
Maximum RF Power: 20 dBm (e.i.r.p)

SOUND BAR WARRANTY

WARRANTY – U.S. Klipsch Group, Inc, (KGI) warrants to the original retail purchaser that this product is to be free from defective materials and workmanship for a period of one (1) year on electronics and three (3) years on woofer, cabinet and non-electrical mechanics, from the date of purchase, if it is properly used and maintained. If this product proves defective in either material or workmanship, KGI, at its option, will (a) repair the product, or (b) replace the product, at no charge for parts or labor. If the product model is no longer available and cannot be repaired effectively or replaced with an identical model, KGI at its sole option may replace the unit with a current model of equal or greater value. In some cases, modification to the mounting surface may be required where a new model is substituted. KGI assumes no responsibility or liability for such modification. To obtain a repair or replacement under the terms of this warranty, please return to dealer first, if possible, and the dealer will direct you accordingly for repairs or replacement. You will be required to submit a copy of the original receipt.
Return shipping for exchanges/repairs is the sole responsibility of the original retail purchaser.

Limitations:

• This limited warranty does not cover failure of the product resulting from improper installation, misuse, abuse, accident, neglect, mishandling, or wear from ordinary use or environmental deterioration.
• This limited warranty does not cover cosmetic damage, including paint damage, or consequential damage to other components or premises which may result for any reason from the failure of the product.
• This limited warranty is null and void for products not used in accordance with KGI’s instructions.
• This limited warranty is null and void for products with altered or missing serial numbers and for products not purchased from an authorized dealer.
• This limited warranty terminates if you sell or otherwise transfer this product to another party.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE, JURISDICTION TO JURISDICTION OR COUNTRY TO COUNTRY. KGI’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPLACEMENT OR REPAIR AS SET FORTH IN THIS WARRANTY  TATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE TERM OF THIS WARRANTY. SOME STATES, JURISDICTIONS OR COUNTRIES DO NOT ALLOW THE EXCLUSION OF CERTAIN IMPLIED WARRANTIES OR CONDITIONS, OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THIS LIMITATION MAY NOT APPLY TO YOU. KGI DOES NOT ACCEPT LIABILITY FOR SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING WITHOUT LIMITATION, ANY LIABILITY FOR THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES OR FOR PRODUCTS NOT BEING AVAILABLE FOR USE. THE MAXIMUM LIABILITY FOR WHICH KGI MAY BE RESPONSIBLE WILL BE NO MORE THAN THE AMOUNT YOU PAID FOR THE PRODUCT THAT IS THE SUBJECT OF THE CLAIM. SOME STATES, JURISDICTIONS OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

WARRANTY OUTSIDE THE U.S.
The Warranty on this product shall comply with applicable law when sold to a consumer outside of the United States.
To obtain any applicable warranty service, please contact the dealer from which you purchased this product, or the distributor that supplied this product.

©2022, Klipsch Group, Inc. Klipsch Group, Inc. is a wholly-owned subsidiary of Voxx International Corporation.
Klipsch and Keepers of the Sound are trademarks of Klipsch Group, Inc., registered in the United States and other countries.
The Bluetooth ® word mark is a registered trademark owned by Bluetooth SIG, Inc. and any use of such mark by Klipsch Group, Inc. is under license.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, the Symbol, DTS and the Symbol together, Virtual:X, and the DTS Virtual:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
V03 – 220609

3502 WOODVIEW TRACE, INDIANAPOLIS, IN, USA
KLIPSCH.COM

Documents / Resources

| Klipsch CINEMA 201 ASB201 Dolby Sound Bar [pdf] User Manual
2ATKO-BAR201, 2ATKOBAR201, CINEMA 201 ASB201, CINEMA 201 ASB201 Dolby Sound Bar, Dolby Sound Bar, Sound Bar
---|---

References

• Patents - DTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>