REEKON P1-L Tagger Construction Label Printer User Guide

REEKON P1-L Tagger Construction Label Printer

Product Information

– Automatic templates for one-click printing of measurements,
materials, locations, assemblies, etc.
Power Source| Rechargeable via USB-C charging cable
Label Roll| Compatible with rolls of labels
Display| OLED screen with REEKON logo
Connectivity| Bluetooth for wireless connection to the ROCK Mobile app
Additional Information| – FCC compliant (part 15 of the FCC Rules)
– For any changes or modifications, seek approval from the
responsible party to avoid voiding the user’s authority to operate
the equipment
– Contact information: www.reekon.tools, CONTACT@REEKON.TOOLS

Product Usage Instructions

UNBOX

The P1-L Construction Label Printer is paired seamlessly with the ROCK Mobile app, allowing users to categorize, mark, and lookup items on the jobsite. The printer supports automatic templates for one-click printing of measurements, materials, locations, assemblies, and more.

OPEN LABEL COVER

• Press down on the Open Tray Latch until the Label Cover opens, exposing the inside of the printer.

UNCOIL LABELS

• Remove the small piece of tape at the beginning of the Label Roll. Unwind 2-3 labels from the roll.

INSERT ROLL

• Insert the roll of labels back into the printer. Ensure that the labels are facing down and that at least one label extends past the front of the cover.

CLOSE COVER

• Close the Label Cover of the printer until a clicking sound is heard and the Label Cover is locked closed. Ensure that at least one label extends outside of the coil.

POWER PRINTER ON

• Press and release the Power ON/OFF button (left side button) until a sound is heard and the REEKON logo appears on the OLED display.

LABEL ALIGNMENT

Align the labels by selecting the Label Feed button and allowing a label to dispense. Once dispensed, rip and discard any exposed labels. Note that the label’s edge should be parallel to the serrated edge. If the labels are misaligned and causing issues, repeat steps 4 and onwards, ensuring that the labels are aligned correctly.

DOWNLOAD ROCK APP

The printer is now ready to print labels. Download the ROCK Jobsite App for Android or iOS and connect to the printer in the Tools menu to begin printing. In the Tools menu of the ROCK Jobsite App, enter the serial name of P1-L, which can be found on the P1-L OLED screen. The serial name needs to be copied exactly.

PRINTER DIAGRAM

UNBOX

The P1-L Construction Label Printer pairs seamlessly with the ROCK Mobile app allowing users to categorize, mark, and lookup anything on the jobsite. Automatic templates allow for one click printing of measurements, materials, locations, assemblies and much more.

Using Instructions

OPEN LABEL COVER

• Press down on the Open Tray Latch until the Label Cover opens, exposing the inside fo the printer.

UNCOIL LABELS

• Remove the small piece of tape at the beginning of the Label Roll. Unwind 2-3 labels from the roll.

INSERT ROLL

• Insert the roll of labels back into the printer. Ensure that the labels are facing down and that at least one label extends past the front of the cover.

CLOSE COVER

• Close Label Cover of printer until clicking sound heard and Label Cover is locked closed. Ensure at least one label is extended outside of the coil.

POWER PRINTER ON

• Press and release the Power ON/OFF button (left side button) until sound is heard and REEKON logo appears on the OLED display.

LABEL ALIGNMENT

• Align the labels by selecting the Label Feed button and allowing a label to dispense. Once dispensed, rip and discard any exposed labels.

NOTE: labels edge should be parallel to serrated edge. Printer may jam if labels are misaligned. If having issues, repeat steps 4 and onward ensuring labels are aligned correctly.

DOWNLOAD ROCK APP

• Printer is now ready to print labels. Download the ROCK Jobsite App for Andriod or iOS and connect to the printer in the Tools menu to begin printing.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. This equipment complies with

FCC radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used with minimum distance 0mm between the radiator and your body.

IC WARNING

• This radio transmitter has been approved by Industry Canada.
• This Class B digital apparatus complies with Canadian standard ICES-003. This device complies with
• Industry Canada License exempt RSS standard(s). Operation is subject to the following two conditions.
• This device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
• This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
• The device has been evaluated to meet general RF exposure requirement. The device can be used with minimum distance 0mm between the radiator and your body.

TECHNICAL ASSISTANCE & REPAIR

• For questions about applications, technical support, repair or more information, please see our website: https://www.reekon.tools
• www.reekon.tools
• CONTACT@REEKON.TOOLS

References

• REEKON Tools - Digital Measuring Tools and Software

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>