GPS CI-2 Air Ionization System Instructions

GPS CI-2 Air Ionization System

Product Information

The CI-2TM air ionization system from GPS Air is a product designed to improve air quality in various applications. It is capable of being installed in a wide range of environments, such as ceiling cassettes, air handlers, mini splits, and PTAC units. The system includes the CI-2 Air Ionization System, CI-2 Mounting Bracket, and Installation Fasteners.

What’s Included

• CI-2 Air Ionization System (1)
• CI-2 Mounting Bracket (1)
• Installation Fasteners (2)

Not Included

• Electrical wiring, junction box, or receptacle to provide power to the CI-2

Location

The CI-2 should be installed after any filtration in the system.
The suitability and actual location of installation may vary based on the equipment manufacturer’s recommendations.

Product Usage Instructions

Installation

1. Review the installation video on the GPS Air website or scan the provided QR code.
2. For low vibration locations on ferrous surfaces, use the integral magnet located on the CI-2. Ensure proper alignment with the indicator on the CI-2.
3. For high vibration or non-ferrous surfaces, use the mounting bracket with appropriate fasteners. Ensure proper alignment with the indicator on the CI-2.

Note: Improper installation methods may result in blocked airflow, improper airflow direction, airflow not interacting with emitters, or exposure to wet conditions. Refer to the provided figures for reference.

Installation Methods

Recommended Installation Locations for Specific Systems

Ceiling Cassette:

1. Optimum installation location is on the fan inlet shroud.
2. Ensure installation of the device does not hinder or interfere with any covers on the ceiling cassette.

Air Handler:

1. Optimum installation location is on the fan inlet.

Mini Split:

1. Mini splits have varying configurations between manufacturers.
2. The blower outlet and coils are the most likely installation locations.
3. Ensure installation of the CI-2 does not hinder covers and guards.

PTAC:

1. PTAC units have varying configurations between manufacturers.
2. The blower outlet and coils are the most likely installation locations.
3. Ensure installation of the CI-2 does not hinder covers and guards.

Wiring

1. GPS recommends powering the CI-2 constantly and not switching it with the system or blower.
2. The CI-2 requires a 24VAC or 12-36VDC power source. Connect the power wires as follows:
   • Black wire: Neutral
   • Red wire: Line
   • Green wire: Dry Contacts / BAS Alarm
   • White wire: Dry Contacts / BAS Alarm
3. Optional: Wire in BAS terminals. The CI-2 is equipped with a set of dry contacts that are normally open and close when the CI-2 is on and has no faults. The contacts are rated up to 125VAC and 300mA.
4. Optional: Use GPS PS-2 for incoming voltages from 110-277VAC.

Operation

• CAUTION! Never touch brushes while the unit is operating to avoid electric shock.
• Once powered, the unit initiates an internal check of all systems. If the auto cleaning wiper blade is not in the home position, it will move to the home position in series with the airflow.
• NOTICE: This product is to be used only as directed. Read entire manual before use. Do not use unless properly installed.
• For technical product queries, please reach out to techsupport@gpsair.com
• Thank you for purchasing a CI-2™ air ionization system from GPS Air.

What’s Included

• Before you start, confirm the contents of your shipment. Each CI-2™ will consist of the following:

1. CI-2 Air Ionization System
2. CI-2 Mounting Bracket
3. Installation Fasteners (2)

Not Included

1. Electrical wiring, junction box, or receptacle to provide power to the CI-2 As part of the installation process, a Startup Document should be completed. For the latest version of the document, visit our website or utilize the QR code.

Location

• WARNING: Make sure power is disconnected to the HVAC equipment before installation.
• NOTE: Use temperature – Maximum ambient temperature in which unit shall be used: 140°F/60°C.
• The CI-2 is capable of being installed in a wide range of applications. Actual location and suitability will vary based on equipment manufacturer. Some recommended installations are below.
• NOTE: Device should be installed after any filtration in system.

Installation

1. Review the installation video at our website or scan the QR code opposite.
2. The integral magnet (see Figure 1) can be used in low vibration locations on ferrous surfaces.
3. The mounting bracket should be used with appropriate fasteners in high vibration and on non-ferrous surfaces. (See Figure 2)
4. Airflow should be aligned with the indicator on the CI-2. (See Figure 3)

Installation Methods

Improper Installation Methods

Ceiling Cassette

1. Optimum installation location is on the fan inlet shroud.
2. Ensure installation of device does not hinder or interfere with any covers on ceiling cassette.

Air Handler

1. Optimum installation location is on the fan inlet.

Mini Split

1. Mini splits are compact by design and configurations will vary greatly between manufacturers.
2. The blower outlet and coils are the most likely installation locations.
3. Ensure installation of the CI-2 does not hinder covers and guards.

PTAC

1. PTAC units are compact by design and configurations will vary greatly between manufacturers.
2. The blower outlet and coils are the most likely locations.
3. Ensure installation of the CI-2 does not hinder covers and guards.

Wiring

1. GPS recommends the CI-2 be powered constantly and NOT switched with the system or blower.
2. The CI-2 requires a 24VAC or 12-36VDC source. Connect the power wires as follows:
   • Black = Neutral
   • Red = Line
   • Green = Dry Contacts / BAS Alarm
   • White = Dry Contacts / BAS Alarm
3. Wire in BAS terminals (optional). The CI-2 is equipped with a set of dry contacts that are normally open and close when the CI-2 is on and has no faults. The contacts are rated up to 125VAC and 300mA.
4. GPS PS-2 (optional). For incoming voltages from 110-277VAC.

Operation

• CAUTION! Never touch brushes while operating, shock may occur.
• Once powered, the unit initiates an internal check of all systems. If the auto cleaning wiper blade is not in the “home” position, it will move to the home position in series with the airflow.

Cleaning Cycle

• The CI-2 comes with a preset cleaning cycle designed to clean the brushes once every day.

Troubleshooting

1. Unit will not power up, LED not illuminated:
   • a. Confirm proper voltage is applied to the correct terminal(s).
   • b. Try disconnecting and re-applying the power source.
2. If the unit does not operate properly after verifying the above instructions please contact GPS for additional assistance.

Product Registration

• By registering your order, the standard limited warranty on eligible products from your purchase is automatically extended to 3 years, at no additional cost.
• Register your products at www.gpsair.com/product-registration or scan the QR code.
• The information provided in this manual is up to date at the time of printing. Any revisions to this document will supersede the content included.
• For the latest applicable version of this manual, visit our website or utilize the QR code.
• 3101 Yorkmont Road Suite 400 Charlotte, NC 28208 980-279-5622
• To access a list of applicable patents, please visit www.gpspatents.com
• © 2022 GPS Air
• www.gpsair.com
• GPS Air is the owner of certain trademarks that appear in our materials. Please visit www.gpsair.com/trademarks for a list of our marks.
• GPS-041-28-R21-CI2 I0M

References

• GPS Air | Optimize Your Indoor Air Quality | GPS Air IAQ Solutions
• Product Registration | GPS
• GPS Air | Optimize Your Indoor Air Quality | GPS Air IAQ Solutions
• GPS Air | Product Registration
• GPS Air | trademarks

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>