American International NDK746 Car Stereo Installation Dash Kit and Accessories Owner’s Manual

American International NDK746 Car Stereo Installation Dash Kit and

Accessories

Product Information

The American International Car Stereo Installation Kits & Accessories are designed to provide a convenient and professional installation solution for car stereo systems. These kits and accessories are specifically designed for Nissan vehicles manufactured between 2009 and 2020, specifically the Nissan 370Z without factory navigation.

Product Usage Instructions

Follow the instructions below to properly install the car stereo using the American International Car Stereo Installation Kit & Accessories:

1. Ensure that the vehicle ignition is turned off and the negative battery cable is disconnected to prevent any electrical damage or injury.
2. Remove the existing car stereo system from the dashboard of your Nissan 370Z without factory navigation.
3. Identify the American International Car Stereo Installation Kit suitable for your Nissan 370Z model year.
4. Assemble the installation kit according to the provided instructions.
5. Connect the wiring harness of the car stereo to the corresponding wires of the installation kit. Ensure proper connections by following the color-coded instructions.
6. Securely mount the car stereo into the installation kit using the appropriate screws or brackets provided in the kit.
7. Reconnect the negative battery cable and turn on the vehicle ignition to test the car stereo functionality.
8. If everything is working correctly, carefully reassemble the dashboard components and ensure they are securely fastened.

Note: It is recommended to refer to the specific instructions provided with the American International Car Stereo Installation Kit & Accessories for detailed guidance on installation steps and any additional precautions specific to your Nissan 370Z model year.

For further assistance or troubleshooting, please consult the product support or contact American International customer service.

DASH DISASSEMBLY INSTRUCTIONS

1. Using a soft tool, unclip the shifter panel.
   Note: This may Include one or two pieces

2. Remove (2) Phillips screws from both side panels of the center console.
   Uncllp and remove the panels.

3. Remove (2) Phillips screws from the bottom dash bezel with the air vents. Uncllp and remove the panel.

4. Remove (4) Phillips screws securing the factory radio trim bezel and A/C control.

5. Remove (4) Phillips screws securing the factory radio to the subdash.

6. Remove (5) Phillips screws securing the climate controls to the dash trim bezel. Save for re assembly.

7. Remove (2) Phillips screws securing the climate control module to the OEM radio brackets. Save for reassembly.

KIT ASSEMBLY INSTRUCTIONS Single ISO Mount Application

1.  Install the OEM climate controls to the NDK746 main frame using the (5) screws removed during disassembly.
2. Install OEM climate control module into the NDK746 brackets using the (2) screw removed during disassembly.
3. Insert pocket Into lower section of the brackets and snap into rear pocket support tabs.
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of radio using screws provided with radio when possible, or screws supplied with kit.
5. Using the main frame of the as a guide, slide radio forward or backward for desired look and then tighten screws to the radio.

Note: Attach a rear support bracket to the rear of the new radio and adjust as necessary to support the weight of the radio. Suggested

Figure A

DOUBLE DIN INSTALLATION INSTRUCTIONS

Double DIN ISO Mount Appllcatlon
See Fig B for bracket tab removal.

1. Install the OEM cllmate controls to the NDK746 main frame using the (5) screws removed during disassembly.
2. Install OEM climate control module Into the NDK746 brackets using the (2) screw removed during disassembly.
3. Remove rear pocket support tabs.
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides of radio using screws provided with radio when possible, or screws supplied with kit.
5. Using the main frame of the as a guide, slide radio forward or backward for desired look and then tighten screws. to the radio.

Note: Attach a rear support bracket to the rear of the new radio and adjust as necessary to support the weight of the radio. Suggested

Figure B
Remove shaded tabs on left and right sides of the brackets (Right side not shown)

American International by PAC

Tech Support : support@aampglobal.com or 727-592-5991
Tech Support in Spat;lish/Para servicio tecnico en espanol, Ila me al+ 1 727 205-0436
Find vehicle applications and additional information at pac-audlo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>