Westfalia 972914 Electric Foam Cutter WEDS150 Instructions

Westfalia 972914 Electric Foam Cutter WEDS150

Dear Customers,
Instruction manuals provide valuable hints for using your new device. They enable you to use all functions, and they help you avoid misunderstandings and prevent damage. Please take the time to read this manual carefully and keep it for future reference. If you pass the device on to third parties, enclose these instructions.

Product Information

SAFETY NOTES

Please note the included General Safety Notes and the following safety notes to avoid malfunctions, damage or physical injury:

• Please read this manual carefully and use the device only according to this manual.
• Dispose of used packaging material carefully or store it out of the reach of children. There is a danger of suffocation!
• Persons with limited physical, sensorial or mental abilities are not allowed to use the device, unless they are supervised and briefed for their safety by a qualified person.
• Do not leave the unit unsupervised while it is turned on. Keep children away while the unit is in use. Do not allow children or people in need of supervision to use the unit.
• Do not continue using the unit after it, or the power cord, have been damaged.
• Do not run the power cord around sharp edges or over hot surfaces.
• Do not touch any hot surfaces. The knife becomes very hot during operation.
• Be extra careful when using the unit around combustible materials.
• Only place the unit on a solid, level surface on the provided stand.
• During cutting harmful fumes may escape. Work only in well aired spaces or under a suitable air extraction system.
• Turn off the unit and pull the power plug while you are not using the unit or before cleaning. Do not pull on the power cord, always grasp the plug itself.
• Allow the unit to cool down before cleaning or storing.
• Do not use the unit outdoors.
• Do not immerse the unit in liquids of any kind. Do not use the unit to heat plastic or liquids.
• Should the unit become damaged do not use it any further and have it repaired by a professional or contact our customer service. Do not disassemble the unit or try repairing it yourself.

Operation

Before first Use

• Remove the device from the packaging and dispose of the packaging material that is not required (e.g. foil) or keep it in a place that is inaccessible to children. There is a risk of suffocation!

Intended Use
The rigid foam cutter is intended for profile and circular cuts in rigid foam panels such as Styrofoam, Alporite, pipe insulation and polystyrene ceiling panels.

Operation

1. Use the included hex key to attach the blade in its holder as shown in the title picture.

2. Insert the plug into a suitable socket. Use the red ON/OFF trigger switch and use the red dial on top of the unit to control the temperature up to a maximum of 550°C. The temperature is ideal when the material is easily cut without overheating and smoking.

3. The device needs a few moments to reach the set temperature. Once the blade has reached the set temperature, it will remain so as long as the ON/OFF switch is pressed.
   Danger! There is a risk of burns! Keep body parts away from the hot blade. Toxic gases are produced when cutting hard foam, polystyrene, etc. Ensure adequate ventilation. Use the sharp edge of the blade to cut out the desired material or to make a cutting line. Use the full width of the blade to cut wide grooves in the material.

4. When finished, release the ON/OFF switch.
   Note that the blade will still be hot for some time. Allow the device to cool down completely before putting it down.

5. When not in use, pull the plug out of the socket.

Cleaning and Storage

• Before cleaning, pull out the mains plug and let the device cool down a bit!
• To clean the device, use the enclosed brass brush and a slightly damp cloth. It is advisable to clean the blade while it is still warm (not hot!). Do not use any aggressive cleaning substances, scouring agents or similar for cleaning.

Technical specifications

• Nominal voltage: 230 V~ 50 Hz
• Rated Power: 150 W
• Temperature range: 0 – 550° C
• Blade Length: 150mm
• Total Length: approx. 42 cm
• Cable length: 2 m
• Weight: approx. 500g
• Protection Class: II

EU DECLARATION OF CONFORMITY

We, the Westfalia Werkzeugcompany, Werkzeugstraße 1, D-58093 Hagen, declare by our own responsibility that the product

Electric Foam Cutter WEDS150
Article No. 97 29 14 is according to the basic requirements, which are defined in the European Directives and their amendments

• 2011/65/EU
  Restriction of the Use of certain hazardous Substances in electrical and electronic Equipment (RoHS)

• 2014/30/EU
  EN 55014-1:2017+A11, EN 55014-2:2015,
  EN 61000-3-2:2014, EN 61000-3-3:2013

• 2014/35/EU
  Low Voltage Directive (LVD)
  EN 60335-1:2012+A11+AC+A13+A1+A14+A15+A1+A2+AC,
  EN 60335-2-45:2002+A1+A2, EN 62233:2008

The technical documentations are on file at the QA department of the Westfalia Werkzeugcompany.

DISPOSAL

Dear Customer,
Please help avoid waste materials. If you at some point intend to dispose of this article, then please keep in mind that many of its components consist of valuable materials, which can be recycled. Please do not discharge it in the rubbish bin, but check with your local council for recycling facilities in your area.

CUSTOMER SERVICES

DEUTSCHLAND
Westfalia
Werkzeugstraße 1
D-58093 Hagen
Telefon: (0180) 5 30 31 32
Telefax: (0180) 5 30 31 30
Internet: www.westfalia.de

SCHWEIZ
Westfalia
Wydenhof 3a
CH-3422 Kirchberg (BE)
Telefon: (034) 4 13 80 00
Telefax: (034) 4 13 80 01
Internet: www.westfalia-versand.ch

ÖSTERREICH
Westfalia
Moosham 31
A-4943 Geinberg OÖ
Telefon: (07723) 4 27 59 54
Telefax: (07723) 4 27 59 23
Internet: www.westfalia-versand.at

References

• Westfalia Versand Österreich | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
• Westfalia Versand Schweiz | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
• Westfalia Versand Deutschland | Werkzeug ✓ Garten ✓ Technik ✓ & mehr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>