HUSKY 1005019757 Heavy Duty Welded Steel Garage Storage User Guide

HUSKY 1005019757 Heavy Duty Welded Steel Garage Storage

THANK YOU
We appreciate the trust and confidence you have placed in Husky through the purchase of this Husky Welded cabinets. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Husky!

To reduce the risk of serious injury, read and follow the safety instructions below before assembling and using this product.

CAUTION: This product is not designed for commercial nor industrial usage.
CAUTION: This product is intended for indoor use only.
CAUTION: Use at least two people to move, assemble or install this product Failure to do so can result in personal injury or product damage.
CAUTION: Close and lock the doors before moving this product.
CAUTION: DO NOT alter this product in any manner This may cause product damage or personal injury.

CAUTION: DO NOT leave children unattended near
to product Cabinet may tip over if improperly
opened.
CAUTION: Check all nuts and bolts periodically for tightness. When required, tighten them.
CAUTION: Keep the product on level surface. The product could become unstable and it may tip over if stored or moved on an uneven surface, which may cause personal injury, death or product damage.
CAUTION: Any assembly or maintenance of the product must be carried out by adults only.
CAUTION: DO NOT stand on the product and do not use it as scaffold.
CAUTION: It Is always recommended to secure this product to the wall with the anti-tip hardware provided.

WARNING

• Unit must be placed on a level surface or leveled with included hardware (When applicable).
• Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
• For safety reasons, it is imperative thatthis unit be mounted on the wall or floor.
• Do not use without installing the tip restraint.
• Unit can tip over causing severe injury or death.
• Never open more than one drawer at a time.
• Do not exceed the recommended weight limits.
• Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
• Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.

Lifetime Warranty for the Cabinets.
1-Year Limited Warranty for Solid Wood Top.This full warranty gives you specific rights, and you may also have other rights, which vary state to state. The manufacturer is not responsible in any way for any damages, losses or inconveniences caused by equipment failure or by user negligence, abuse, or use non-compliant with the user manual or any additional safety, use, or warnings included in the product packaging and manual.
This warranty does not apply to the following:
Incidental/inconsequential damages and failures due to misuse, abuse, accident, alteration, or normal wear and tear.  Improper or inadequate maintenance.Damage in return transit. Unsupervised use by children under 18 years of age.
Contact the customer service team at 1-888-HD- HUSKY or visit www.huskytools.com.

Pre-installation

WEIGHT CAPACITY

TOOLS REQUIRED

BEFORE YOU BEGIN

• Begin by placing the package on a flat surface.
• Remove all cardboard, foam packaging material and clear plastic bags.
• Dispose or recycle all packaging materials.
• Verify all the contents in the box and gather tools required.

PACKAGE CONTENTS

NOTE: Hardware not shown to actual size.  Some of the hardwares offered may be more than needed, please keep them as spare parts.

Tall Cabinet Package Contents

Split Cabinet Package Contents

Wall Cabinet Package Contents

Door Cabinet Package Contents

Operation (Continued)

Removing the Drawer

• Empty the drawer, and extend the drawer completely.
• There are two black plastic levers on each side of the drawer. Pull up the left one while pushing down on the right one.
• Hold both levers and pull the drawer outward until it is released from the drawer slides.

Installing the Drawer

• Extend the drawer slide completely from the cabinet.
• Align the slide on the drawer with the slide inside the cabinet and make sure both left and right slides are properly positioned.
• Slide in the drawer and close it completely to finish the installation.

NOTE: DO NOT slide in the drawer violently until both drawer slides are aligned properly or it will cause damage on drawer slide.

NOTE: DO NOT slide in the drawer violently until  both drawer slides are aligned properly or it will cause damage on drawer slide.

Assembling the Tall Cabinet

Installing the Closet Rod

• Insert the right end of the closet rod (I) into the slot, and then slide down the left end.
  NOTE: Remove the pull out drawer before install the closet rod, and refer to page of removing the drawer.
  Installing the Rubber Grommets

• Insert rubber grommets (JJ) into the cut-off holes in the back panel.
  NOTE: Use a box knife to cut along the perforation in the U rubber grommets to create holes when necessary.

Adjusting the Leveling Feet

• Adjust the feet from inside the cabinet to make it level using the wrench (KK).
• Install the plastic cap(NN).

Attaching the Cabinet onto Studded Wall

• Use a stud finder to locate the studs and mark the wall with a pencil.
• Place the cabinet against the wall and align it to the stud marks.
• Level the cabinet. (Adjust the leveling feet when necessary.)
• Drill two wall screws (HH) and two washers (CC) into the wall.

Installing the Shelf

NOTE: Make sure all the clips are at the same level.

• Open the cabinet and insert the shelf clips (AA) into the perforated holes on each corner of the cabinet.
• Insert the shelf (F) on an angle and rotate to the level position.
• Lower the shelf onto the clips.
• Install the other shelf (F).

Adjusting the Pull Out Drawer in Tall Cabinet ( 1 )

• Remove the pull out drawer.
• Switch out the front side of the plate (1) slightly and lift up the rear part (2) to remove the drawer slide.
• Remove the other drawer slide.

Adjusting the Pull Out Drawer in Tall Cabinet (2)

• Insert the rear (2) of the drawer slide first, and then insert the front (1) afterwards.
• Insert the other drawer slide.
• Install the pull out drawer (J).

Using the Tall Cabinet Catch Plate

• Slide the latch and pull snap joint.
• Push and press the catch plate back to the bottom.

NOTE: When opened, the angle between the bottom panel and catch plate is 90°.

Assembling the Base Cabinet

Installing the Adjustable Feet

NOTE: Remove all the loose items inside the cabinet  before uttin down the cabinets.

• Locate the center hole on the bottom panel at each corner and screw the adjustable foot (II) into the center hole.
• Stand the cabinet and level the feet (II).

Installing the Casters (Optional)

NOTE: Remove all the loose items inside the cabinet before putting down the cabinets.

NOTE: Ensure the two casters with brake are on the same side and not diagonal from each other

• Locate the holes forming a square on the bottom of the cabinet.
• Align the caster with brake onto the holes.
• Secure the caster with brake using four bolts and four washers. Wrench tighten.
• Secure the other caster with brake using four bolts and four washers on the same side.
• Secure the two casters without brake using eight bolts and eight washers. Wrench tighten.

Installing the Shelf

NOTE: Make sure all the clips are at the same level.

• Open the cabinet and insert the shelf clips (AA) into the perforated holes on each corner of the cabinet.
• Insert the shelf (M) on an angle and rotate to the level position.
• Lower the shelf onto the clips (AA).

Install the Shelf for 2 Door Cabinet

Install the Shelf for Wall Cabinet

Installing the Anti-tip Bracket
Secure Anti-tip Bracket on Base Cabinet

• Locate the two holes on top of the back panel on each side of the cabinet.
• Place the anti-tip bracket (EE) and secure it with bolts (BB).
• Secure the other bracket (EE) with bolts (BB).

Secure Anti-tip Bracket to the Drywall

• Put the cabinet against the wall.
• Drill a pilot hole through the top perforated hole on the bracket (EE) and insert the plastic anchor into the pilot hole.
• Secure the bracket (EE) using a drywall screw (GG) and washer (CC).

Secure Anti-tip Bracket to the Studded Wall

• Put the cabinet against the wall.
• Drill a wall screw (HH) through the top perforated hole on the bracket (EE).
• Secure the bracket (EE) with wall screw (HH) and washer (CC).

NOTE: One bracket will be locked onto the studs or  both will be locked onto the drywall.

Adjusting the Door Hinge

• To adjust the doors in or out from cabinet, turn the screw (5) clockwise or counterclockwise.
• To adjust the doors left or right, turn the screw (6) clockwise or counterclockwise.

Installing the Wall Cabinet

Hanging the Wall Cabinet

• Use a stud finder to locate the studs and mark the wall with a pencil.
• Align the bracket (E) with two notches on the tall cabinet and level the bracket.
• Lock the bracket onto the wall with three wall screws (HH) and three washers (CC).
• Align and lock all the other brackets (E).

Hanging the Wall Cabinet (2)

• Hang the wall cabinets (B) onto the bracket (E).

Fastening the Cabinets

• Locate the four cut-off holes on the side panel of the wall cabinet and tall cabinet.
• Secure the cabinets with four bolts (BB), eight washers (CC) and four nuts (DD).
• Secure all the other cabinets together.
• Secure the bottom of the cabinet (B) onto the wall with two wall screws (GG), two plastic anchor(FF) and two washers(CC).

Troubleshooting

cabinet is leveled.
Doors are not aligned.| The hinge is not adjusted properly.| Adjust the door hinge until the doors are aligned.
The kick plate for tall cabinet is not touching the floor,| The kick plate is stuck.| Move the kick plate up and down to release it so that it can touch the floor,

Care and Cleaning

• Prior to cleaning, first turn off and unplug all the electrical devices from the power source.
• Use a dry or slightly dampened, clean cloth to wipe the exterior of the cabinets.
• Allow the electrical devices to dry completely before connecting to power and operating.
• Apply lubricating agent on some operative components such as drawer slides and hinges every six months. For Line-X coated items:
• Use a mild detergent and water with a clean cloth to wipe the exterior of the cabinets.
• The use of harsh solvents (e.g. acetone) is not recommended for cleaning.

Questions, problems, missing parts? Before returning to the store, call Husky

Customer Service

• 8 a.m. – 7 p.m., EST, Monday-Friday, 8 a.m. – 6 p.m., EST, Saturday
• 1-888-HD-HUSKY
• HUSKYTOOLS.COM

Retain this manual for future use.

• HUSKYT00LS.C0M
• Please contact 1-888-HD-HUSKY for further assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>