olympia electronics BS-661-A Waterproof Heat Of Rise Detector Instruction Manual
- June 12, 2024
- olympia electronics
Table of Contents
European manufacturers
BS-661/Α
WATERPROOF
HEAT OF RISE DETECTOR
Thank you for your trust in our products Olympia Electronics – European manufacturer
Package Contents
- 1 Detector
- 1 Mounting Accessories
- 1 Manual
General
The user have to read carefully the following instructions, in order to be
properly informed and keep them for future use.
The BS-661/A is a conventional heat detector which integrates the function of
rate-of-rise heat detection. The detector transitions to alarm state when the
temperature reaches 57 °C. Also, the detector transitions to alarm state when
the temperature rises suddenly by 32 °C regardless of the initial temperature
at the beginning of the sudden rise event.
The detector have a visible led and a remote led driver which are light up
constantly in case of detection of fire, till cancelled from the panel.
They are turned off only when a reset command is given from the panel.
The indicator led blinks every 7 sec indicating the normal function.
INSTALLATION
For spacings, heights and all mounting points consult the local/national
regulation or the standard EN 54-14/2018. The detectors must be placed at
least 50 cm away from fluorescent lamps. Cable cross-section should be from
0.5 to 2.5mm .
MAINTENANCE & FUNCTIONAL TESTING
The detector has fault diagnosis function, which automatically informs you
through the onboard LED when detector replacement is required.
The indication LED blinks every 7 seconds. In normal operation it blinks 1
time and if there is a failure it blinks 3 times. These functions combined
with periodic manual testing ensure maximum security level.
It is suggested to carry out a test every 6 months or after a change in the
position of the sensor.
CAUTION !!
After installation the device must not be covered with dust or be painted or
anything else happen that will block the air to get to the sensor. Special
attention must be given during the installation and the use of the device,
since the user assumes full responsibility for proper operation afterwards.
Installation Instructions
CONNECTION DIAGRAM
Dimensions (mm)
Technical Characteristics
| BS-661/A
---|---
OPERATION VOLTAGE| 17-30V DC
START UP POWER CONSUMPTION| 1mA for 2 sec
STANDBY CONSUMPTION| 90μA
ALARM CONSUMPTION| 12mA (with activated on board LED)
TEMPERATURE SENSITIVITY| 57 °C
CLASS| Α2R
INDICATORS| Alarm LED
OUTPUT| To panel / to external LED (BS-572)
DEGREES OF COVER PROTECTION| IP65
PRODUCED IN ACCORDANCE WITH| EN 54-5
OPERATING TEMPERATURE RANGE| 40 to 70 °C
RELATIVE HUMIDITY| Up to 95%
CONSTRUCTION MATERIALS| ABS/PC
EXTERNAL DIMENSIONS ( L X W X H)| 164 x 80 x 45mm
TYPICAL WEIGHT (NET/GROSS)| 140 /185 gr.
GUARANTEE| 2 years
BS-661/A
Waterproof heat of rise detector
EN 54-5:2017+A1:2018
DoP: 921661001_59_001
1922 – CPR – 1968
EGINIO
PIERIAS
60300
GREECE
Warranty
Olympia Electronics guarantees the quality, condition and operation of the
goods. The period of warranty is specified in the official catalogue of
Olympia Electronics and also in the technical leaflet, which accompanies each
product.
This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if
the buyer modifies the goods provided or has any repairs or re-setting done by
a third party, unless Olympia Electronics has fully agreed to them in
writing.
Products that have been damaged can be returned to the premises of our company
for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned
goods and to or not charge the buyer depending on the reason of defection.
Olympia Electronics reserves the right to charge or not the buyer the
transportation cost.
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
[email protected]