CYABER Car Battery Jump Starter User Manual
- June 7, 2024
- CYABER
Table of Contents
- CYABER Car Battery Jump Starter User Manual
- Package Content
- Introduction
- Key Features
- Know Your Product
- Powerful circuit protection system – Smart Clamps
- Getting Started
- Turn On your Jump Starter
- LED Light
- QC3.0 & 5V 2.4A Dual USB Output
- Start your Car
- Cautions
- Warranty
- Contact US
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CYABER Car Battery Jump Starter User Manual
Package Content
1 x Jump Starter 1 x Smart Jumper clamps 1 x Type C Cable
1 x User Manual 1x EC5 Cigarette Lighter Adapter 1 x Storage Case
Introduction
Thank you for purchasing YABER YR800 car jump starter. Please read the user manual carefully before you start to use the product.
Key Features
★A Powerful Jump Starter: Car Jump Starter with 2500 amps peak current can
jump starts 12V cars, SUV, truck or van (all gasoline and 8L diesel) in
seconds up to 30 times.
★To encure the faster charging efficiency, this external battery charger is
equipped with two USB Output including USB1 (QC3.0 5V 3A / 9V 2A / 12V
1.5A),USB2 (5V 2.4A) and 5V 2A Type C input.
★Safety Protection: Premium cells, circuitry and safety features protect you
and your device from surge or short circuits.
★ LED Lights & LCD Screen：LED light that has 3 mode: flashlight/ strobe/ SOS,
that could use as emergency tool, extra red warning light can remind the
passing cars if there is an accident. The LCD screen
can exactly show the remaining power and output voltage.
★Convenient wireless charging：If you forget bring a charging cable,this jump
starter is your best choice.10W quickly wireless charger or power bank on the
go.
★Car saftey hammer: The jump starter with hardened sharp Stainless Steel
Points can shatter vehicle windows in an emergency.
Know Your Product
① Jump starting port
② Flashlight
③ QC 3.0 USB output
④ 5V/2.4A USB output
⑤ Type C input
⑥ LCD display
⑦ Power swtich
⑧ Wireless charger
⑨ Compass
⑩ Saftey hammer
Powerful circuit protection system – Smart Clamps
① Red jumper cable (+)
② Black jumper cable (-)
③ “Smart Clamp” plug
Getting Started
Charging your Jump Starter
- Please use a 5V2A/9V2A/12V1.5A adapter to charge the product.(Type C cable is included, adapter is not included)
- Using a 5V/2A adaptor, it will take approximately 5-6 hours to fully charge the unit. In order to extend the battery life it is recommended to fully charge the unit every 3-6 months.
Turn On your Jump Starter
Short press the power switch to boot the jump starter, the display will be
turned on. For energy saving, the jump starter will be turned to standby
mode if there is no operation within 20 seconds.
LED Light
Turn on the jump starter. Long press the power switch more than 3 seconds to
turn on the flashlight mode. There are four modes including illumination, SOS
and Strobe, warning light. Short press the power switch
button to change the 3modes(illumination, SOS and Strobe) or turn off the
flashlight mode. Double press the power switch button to enter the warning
light mode or turn off the warning light mode.
QC3.0 & 5V 2.4A Dual USB Output
This portable jump starter is also equipped with two smart USB outputs that
provide the fastest charging speed(USB1 – QC3.0: 5V 3A / 9V 2A /12V 1.5A; USB2
– 5V 2.4A) for your portable electronic devices, such as
phones,tablets, bluetooth earphones, etc
Start your Car
-
Please make sure that battery level is above 50% before you use it to jump start your car.
-
Insert the plug of the smart clip completely into the jump starter, the green and red lights flash alternately
-
Correctly clip the red and black clamps to the electrodes of the car battery (red to positive and black to negative)(The green light stays on)
-
Start the vehicle.
-
When the vehicle is started, remove the jumper cable from the vehicle battery immediately.
In any of the following situations, the smart clamp turns on protection mode:
| LED Indicator | Situations |
|---|---|
| The red/green led will flash | Ready to work |
| The green light is always on | Work status |
The red light is always on
| 1. battery clamp is reversely connected
— check whether the clip is reversely connected
2. The clamp is short-circuited
—check whether two clamps together connect or connect both cable clamps to the same piece of metal
---|---
The red light flashes slowly
| Back change protection, the voltage of the car battery is higher than 12.6V
-No jump starter needed, the car battery is enough to star your car
The red LED flashes quickly
| The temperature of the clamp exceeds 65(+/-5)degrees— remove the clamp untill the red green led flash
The green light flashes slowly
| The vollage of the starter is too low
–try to replace the startup power supply or change it in time
Cautions
- Use the original smart clip to start the car.
- DO NOT use this unit if any cable clamp or cord is damaged.
- Start only for 12V vehicles,or it will cause serous damages to the unit.
- Do not jump start your car when the battery capacity is lower than 50%.
- Do not connect two clamps together when the starter is powered on. And do not connect both cable clamps to the same piece of metal.
- If the engine does not start on the first try, disconnect it from the car battery and wait for at least 20 seconds before reconnecting. Maximize three attempts in two minutes.
- Once the engine is successfully started, disconnect the clamps within 30 seconds.
EN 06|
Cautions
- Use the original smart clip to start the car.
- DO NOT use this unit if any cable clamp or cord is damaged.
- Start only for 12V vehicles,or it will cause serous damages to the unit.
- Do not jump start your car when the battery capacity is lower than 50%.
- Do not connect two clamps together when the starter is powered on. Andb do not connect both cable clamps to the same piece of metal.
- If the engine does not start on the first try, disconnect it from the car battery and wait for at least 20 seconds before reconnecting. Maximize three attempts in two minutes.
- Once the engine is successfully started, disconnect the clamps within 30 seconds.
| Model | YR800 |
|---|---|
| USB 1 OUTPUT | QC3.0 5V 3A / 9V2A /12V1.5A |
| USB2 Output | 5V 2.4A |
| Type-C Input | 5V 2A |
| Short circuit protection | √ |
| Over-discharge protection | ≦ 13v ± 0.3v |
| Over-temperature Protection | ＞65 ℃ ± 5 ℃ |
| Reverse polarity protection | √ |
| Reverse charging protection | ≧ (12.6v ± 0.3v) |
| wireless charge | 10w |
| Dimension | 1809343mm |
FAQ & Trouble Shooting
Q: How to turn off this power pack?
A: This power pack will power off automatically when no load or charging is complete.
Q: What kind of adapter should I use?
A: You can use the adapter of your phone or tablet..
Q: How long time to full charge the YABER YR800 jump starter? A: About 5-6 hours through the 5V2A AC adapter.
Q: How many times can this product start the vehicle with full capacity? A: Up to 30 times.
Care and Maintenance
- DO NOT put the product under direct sunlight or hot areas.
- DO NOT drop or knock your car jump starter.
- DO NOT disassemble the equipment, it may cause damage.
- DO NOT use chemicals or detergents to clean the product.
- DO NOT place the products in high temperature environment for long. The operating temperature: -20~60℃.
- Check the power of the product at least every three months, and charge the product in time.
EN 07|
Warranty
Our company provides customers with warranty of 24 months from the date of purchase.
Contact US
For additional assistance or warranty cover claim, please contact us: E-Mail:
support@yaberauto.com
For additional assistance or warranty cover claim, please contact us: E-Mail:
support@yaberauto.com
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>