QUICKIE EASY 200/300 Wheel Chair Instruction Manual

WHEELCHAIR
ROLLSTUHL Easy 200/300

DIRECTIONS FOR USE

www.sunrisemedical.com

If you are visually impaired, this document can be viewed in pdf format at www.SunriseMedical.co.uk.

Wheelchair Components
We at SUNRISE MEDICAL have been awarded the ISO-13485 certificate, which affirms the quality of our products at every stage, from R & D to production. This product complies with the standards set forth in EU and UK regulations. Options or accessories shown are available at extra cost.

Wheelchairs:

1. Push handles
2. Backrest upholstery
3. Sideguard
4. Seat sling
5. Footrest
6. Castors
7. Footboard
8. Fork
9. Quick-release axle
10. Wheel locks
11.  Handrim
12.  Rear wheel

Foreword

Dear Customer,
We are very happy that you have decided in favour of a highquality product from SUNRISE MEDICAL.
This owner’s manual will provide numerous tips and ideas so that your new wheelchair can become a trustworthy and reliable partner in your life.
Maintaining close ties to our customers means a lot to us at Sunrise Medical. We like to keep you up-to-date about new and current developments at our company. Keeping close to our customers means: fast service, as little red tape as  possible, working closely with customers. When you need replacement parts or accessories, or if you just have a question about your wheelchair – we are there for you.
We want you to be satisfied with our products and service.
At Sunrise Medical we are constantly working to develop our products further. For this reason, changes can occur in our palette of products with regard to form, technology and equipment. Consequently, no claims can be construed from the data or pictures contained in this user’s manual.
The management system of SUNRISE MEDICAL is certified to EN ISO 13485 and ISO 14001.
**As the manufacturer, SUNRISE MEDICAL, declares that this product conforms to the UK
Medical Devices Regulation 2002 No. 618.
As the manufacturer, SUNRISE MEDICAL, declares that this product conforms to the Medical Device
Regulation (2017/745).
Notice to the user and/or patient: Any serious incident that has occurred in relation to the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established.
B4Me special adaptations
Sunrise Medical strongly recommends that in order to ensure that your B4Me product operates, and performs as intended by the manufacturer; all the user information supplied with your B4Me product is read and understood, before the product is first used.
Sunrise Medical also recommends that the user information is not discarded after reading it, but it is kept safely stored for future reference.
Medical Device Combinations**
It may be possible to combine this Medical device with one or more other Medical Device or other product. Information on which combinations are possible can be found at www.Sunrisemedical.co.uk. All combinations listed have
been validated to meet the General Safety and Performance
Requirements, Annex I Nr. 14.1 of the Medical Device
Regulation 2017/745.
Guidance on the combination, such as mounting, can be found at www.SunriseMedical.co.uk

Please contact your local, authorised SUNRISE MEDICAL dealer if you have any questions concerning the use, maintenance, or safety of your wheelchair.
In case there is no authorised dealer in your area, or you have any questions, contact Sunrise Medical either in writing or by telephone.
Sunrise Medical
Thorns Road
Brierley Hill
West Midlands
DY5 2LD
England
Phone: 0845 605 66 88
Fax: 0845 605 66 89
www.SunriseMedical.co.uk

IMPORTANT:
DO NOT USE YOUR WHEELCHAIR UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD.
NOT FOLLOWING THESE INSTRUCTIONS MAY RESULT IN PHYSICAL INJURY, DAMAGE TO THE PRODUCT OR DAMAGE TO THE ENVIRONMENT!

Use

Wheelchairs are exclusively for a user who is unable to walk or has limited mobility, for their own personal use, when self-propelling and being moved by a third party (pushed by attendant) within the home and outdoors.
The maximum weight limit (includes both the user and any weight of accessories fitted to the wheelchair) is marked on the serial number label, which is affixed to the crossbar or stabiliser bar below the seat.
Warranty can only be taken on if the product is used under the specified conditions and for the intended purposes.
The intended lifetime of this product is 5 years.
NO NON-STANDARD PARTS are to be fitted, other than those officially approved by Sunrise Medical.

Area of Application.

Indications
The varieties of fitting variants, as well as the modular design, mean that it can be used by those who cannot walk or have limited mobility because of:

• Paralysis
• Loss of extremity (leg amputation)
• Extremity defect deformity
• Joint contractures/joint injuries
• Illnesses such as heart and circulation deficiencies, disturbance of equilibrium or cachexia, Neurological disease patterns, Muscle dystrophy, Hemiplegia as well as for elderly people who still have strength in the upper body.

Contraindications
The wheelchair shall not be used without attendant in case of:

• Perception disorder
• Imbalance
• Loss of both arms, if not supported by a caregiver
• Joint contracture or joint damage on both arms
• Seating disability

NOTE:
Please note that driving a wheelchair requires sufficient cognitive, physical and visual skills. The user must be able to assess the effects of actions during the operation of the wheelchair and, if necessary, to correct them. These capabilities and the safe use of the additionally attached components cannot be assessed by Sunrise Medical as a manufacturer. We cannot accept any liability for any damage resulting from this.
Please refer to the operating instructions of the wheelchair and the additionally mounted components. Instruct the user in the safe use of the wheelchair and the additionally mounted components. Inform users of specific warnings that  need to be read, understood, and respected.
When considering provision, please also note the body size, weight, physical and psychological constitution, the age of the person, living conditions and environment.

Definitions

3.1 Definitions of words used in this manual

the advice is not followed
WARNING!| Advice to the user of a potential risk of injury if the advice is not followed
CAUTION!| Advice to user that potential
damage to equipment may occur if the advice is not followed
NOTE:| General advice or best practice
| Reference To Additional Documentation

NOTE:
Please keep a note of your local service agent’s address and telephone number in the space provided.
In the event of a breakdown, contact them and try to give all relevant details so they can help you quickly.

NOTE:
The wheelchairs shown and described in this user guide may not correspond in every detail exactly to your own model.
However, all instructions are completely relevant, regardless of possible detail differences.
The manufacturer reserves the right to alter without notice any weights, measurements or other technical data shown in this manual. All figures, measurements and capacities shown in this manual are approximate and do not constitute specifications.

General safety notes and driving limits

The engineering and construction of this wheelchair has been designed to provide maximum safety. International safety standards currently in force have either been fulfilled or exceeded in parts. Nevertheless, users may put themselves  at risk by improperly using their wheelchairs. For your own safety, the following rules must be strictly observed.
Unprofessional or erroneous changes or adjustments increase the risk of accident. As a wheelchair user, you are also part of the daily traffic on streets and pavements, just like anyone else.
We would like to remind you that you are therefore also subject to any and all traffic laws.
Be careful during your first ride in this wheelchair. Get to know your wheelchair.
Before each use, the following should be checked:

• Quick-release axles on the rear wheels
• Velcro on seats and backrests
• Tyres, tyre pressure and wheel locks.

Before changing any of the adjustments of this wheelchair, it is important to read the corresponding section of the user’s manual.
It is possible that potholes or uneven ground could cause this wheelchair to tip over, especially when riding uphill or downhill.
When riding forwards over a step or up an incline, the body should be leaning forward.

DANGER!

• NEVER exceed the maximum load of 140 kg, (136kg crash tested), for driver plus any items carried on the wheelchair.
  Please note the weight information for lighter weight options, which are quoted separately. If you exceed the maximum load, this can lead to damage to the chair, or you may fall or tip over, lose control and may lead to serious injury of the user and other people.

• When it is dark, please wear light clothing or clothing with reflectors, so that you can be seen more easily. Make sure that the reflectors on the side and back of the wheelchair are clearly visible. We would also recommend that you fit an active light.

• To avoid falls and dangerous situations, you should first practice using your new wheelchair on level ground with good visibility.

• When getting on or off the wheelchair, do not use the footboards. These should be flipped up beforehand and swung to the outside as far as possible. Always position yourself as close as possible to the place where you wish to sit.

• Only use your wheelchair properly. For example, avoid travelling against an obstacle without braking (step, kerb edge) or dropping down gaps.

• The wheel locks are not intended to brake your wheelchair. They are only there to ensure that your wheelchair does not begin rolling unintentionally. When you stop on uneven ground, you should always use the wheel locks to  prevent such rolling. Always apply both wheel locks; otherwise, your wheelchair could tip over.

• Explore the effects of changing the centre of gravity on the behaviour of the wheelchair, for example on inclines, slopes, all gradients or when overcoming obstacles. Do this with the secure aid of a helper.

• With extreme settings (e.g. rear wheels in the most forward position) and less than perfect posture, the wheelchair may tip over even on a level surface.

• Lean your upper body further forward when going up slopes and steps.

• Lean your upper body further back when going down slopes and steps. Never try to climb and descend a slope diagonally.

• Avoid using an escalator which may lead to serious injury in the event of a fall.

• Do not use the wheelchair on slopes > 10°. The Dynamic safe slope is dependent on the chair configuration, the user#s abilities and the style of riding. As the user’s abilities and style of riding cannot be pre-determined then the max safe slope cannot be determined. Therefore this must be determined by the user with the assistance of an attendant to prevent tipping. It is strongly recommended that inexperienced users have anti-tip tubes fitted.

• It is possible that potholes or uneven ground could cause this wheelchair to tip over, especially when riding uphill or downhill.

• Do not use your wheelchair on muddy or icy ground. Do not use your wheelchair where pedestrians are not allowed.

• To avoid hand injuries do not grab in between the spokes or between the rear wheel and wheel lock when driving the wheelchair.

• In particular when using lightweight metal handrims, fingers will easily become hot when braking from a high speed or on long inclines.

• Riding sideways on to a slope or incline, increases the possibility of the wheelchair tipping over sideways.

• Only attempt stairs with the help of an attendant. There is equipment available to help you, e.g. climbing ramps or lifts, please use them. If there is no such equipment available, then the wheelchair must be tipped and pushed, never  carried, over the steps (2 helpers). We recommend that users over 100 kg in weight do not use this stairway manoeuvre!

• In general, any anti-tip tubes fitted must be set beforehand, so that they cannot touch the steps, as otherwise this could lead to a serious tumble. Afterwards the anti-tip tubes must be set back to their correct position.

• Make sure that the attendant only holds the wheelchair using securely mounted parts (e.g. not on the footrests or the sideguards).

• This wheelchair is not designed to be used whilst weight training and/or when using dumbbells. Only use equipment specifically designed for this purpose.

• Do not lift or carry the wheelchair by the backtubes or the pushhandles.

• When using the lifting ramp make sure that the anti-tip tubes fitted are positioned outside the danger area.

• Secure your wheelchair on uneven ground or when transferring, e.g. into a car, by using the brakes.

• If and whenever possible, during a journey in a specially fitted vehicle for disabled people, vehicle occupants should use the seats in the vehicle and the appropriate restraint system. This is the only way to ensure that occupants will have the maximum protection if there is an accident. When using safety elements offered by SUNRISE MEDICAL and using a specially designed safety system, lightweight wheelchairs can be used as a seat when being transported in a specially fitted vehicle. (See the Chapter on “Transportation”).

• Depending on the diameter and setting of the castors, as well as the centre of gravity setting of the wheelchair, the castors may begin to wobble at high speeds. This can lead to the castors being blocked and the wheelchair may tip over. Therefore, please make sure that the castors are adjusted correctly (see the Chapter “Castors”). In particular, do not travel on an incline without brakes, travel at a reduced speed. We recommend that novice users use antitip tubes.

• Anti-tip tubes should prevent the chair tipping over backwards unintentionally. Under no circumstances should they take the place of transit wheels, and be used to transport a person in a wheelchair with the rear wheels removed.

• When reaching for objects (which are in front of, to the side or behind the wheelchair) make sure that you do not lean too far out of the wheelchair, as if you change the centre of gravity there is a risk of tipping or rolling over. The  hanging of additional load (back pack or similar items) onto your chair backposts can affect the rearward stability of your chair, especially when used in combination with recliner backrests. This can cause the chair to tip backwards causing injury.

• Adjustments to your wheelchair, particularly to safetyrelated components must be carried out by an approved dealer.
  This applies to adjustments to wheel locks, anti-tip tubes, backrest angle and height, lower leg length, COG, Pelvic Restraint Belt, rear wheel toe-in and camber, seat height as well as toe-in and directional stability of the castor fork.

• When using mobility accessories fitted to the wheelchair such as handbikes, electronic power assist, etc, make sure that your wheelchair is fitted with the appropriate castor forks, approved for this use. Please contact your dealer if you have any questions.

• Do not fit any unauthorized electronic equipment, powered or mechanically operated mobility drives, hand-bike or any other device that changes the intended use or the structure of the wheelchair.

• Any combination with other medical devices requires the approval of Sunrise Medical.

• Please note that in certain configurations the wheelchair may exceed a width of 700 mm. If this is the case, under certain circumstances, it may not be possible to use some or all of the available escape routes from a building. It may be more difficult or impossible to travel on public transport.

• Further information and safety instructions can be provided by your authorised dealer.

• For thigh amputees you must use anti-tip tubes.

• Before setting off, check that your tyre pressure is correct. For rear wheels it should be at least 3.5 bar (350 kPa). The max. pressure is indicated on the tyre. The knee-lever brakes will only work if there is sufficient tyre pressure and if the correct setting has been made (see the Chapter on “Brakes”).

• If the seat and back sling are damaged, you must replace them immediately.

• Be careful with fire, in particular with burning cigarettes. Seat and back slings can be set alight.

• If the wheelchair is subject to direct sunlight for a long period of time, then parts of the wheelchair (e.g. frame, legrests, brakes and sideguard) may become hot (>41°C).

• Always make sure that the quick-release axles on the rear wheels are set properly and lock in. If the button on the quick-release axle is not pressed in, the rear wheel cannot be removed.

Warranty

THIS GUARANTEE DOES NOT AFFECT YOUR LEGAL RIGHTS IN ANY WAY.
Sunrise Medical* provides a guarantee, as set out in the warranty conditions, for wheelchairs to its customers covering the following.
Warranty conditions:

1. Should a part or parts of the wheelchair require repair or replacement as a result of a manufacturing and/or material fault within 24 months or for frame and cross-braces within 5 years after delivery to the customer, then the  affected part or parts will be repaired or replaced free of charge. The warranty will only cover manufacturing defects

2. To enforce the warranty, please contact Sunrise Medical Customer Service with the exact details of the nature of the difficulty. Should you be using the wheelchair outside the area covered by the Sunrise Medical customer service  agent, repairs or replacement will be carried out by another agency as designated by the manufacturer The wheelchair must be repaired by a Sunrise Medical designated Customer Service agent, (dealer).

3. For parts, which have been repaired or exchanged within the scope of this warranty, we provide a warranty in accordance with these warranty conditions for the remaining warranty period for the wheelchair in accordance with point  1).

4. For original spare parts which have been fitted at the customer’s expense, these will have a 12 months guarantee, (following the fitting), in accordance with these warranty conditions.

5. Claims from this warranty shall not arise, if a repair or replacement of a wheelchair or a part is required for the following reasons:
   a. Normal wear and tear, which include batteries, armrest pads, upholstery, tyres, brakes shoes, etc.
   b. Any overloading of the product, please check the EC label for maximum user weight.
   c. The product or part has not been maintained or serviced in accordance with the manufacturer’s recommendations as shown in the user instructions and/or the service instructions.
   d. Accessories have been used which are not specified as original accessories.
   e. The wheelchair or part having been damaged by neglect, accident or improper use.
   f. Changes/modifications have been made to the wheelchair or parts, which deviate from the manufacturer’s specifications.
   g. Repairs have been carried out, before our Customer Service has been informed of the circumstances.

6. This guarantee is subject to the law of the country in which the product was purchased from Sunrise Medical*

• Means the Sunrise Medical facility from which the product was purchased.

Additional Notes For Australia Only:

1. For goods provided by Sunrise medical Pty Ltd in Australia, our goods come with a guarantee by Sunrise Medical that cannot be excluded under Australian Consumer Law.
2. You are entitled to a replacement or refund for a major failure and for compensation for any foreseeable loss or damage.
3. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
4. The benefits to you given by this warranty are in addition to your other rights and remedies under a law in relation to the goods to which the warranty relates.

Transportability

DANGER!
There is a risk of serious injury or death if this if this advice is ignored!
Transportation of your wheelchair within a vehicle:
A wheelchair secured in a vehicle will not provide the equivalent level of safety and security as a vehicle seating system. It is always recommended that the user transfers to the vehicle seating. It is recognised that this is not always  practical for the user to be transferred and in these circumstances, where the user must be transported whilst in the wheelchair, the following advice must be followed:

1. Confirm that the vehicle is suitably equipped to transport a passenger in a wheelchair, and ensure the method of access/egress is suitable for your wheelchair type. The vehicle should have the floor strength to take the combined  weight of the user, the wheel chair and accessories.
2. Sufficient space should be available around the wheelchair to enable clear access to attach, tighten and release the wheelchair and occupant tie down restraints and safety belts.
3. The occupied wheelchair must be located in a forward facing position and secured by the wheelchair tie down and occupant restraint straps (WTORS tie downs meeting the requirements of ISO 10542 or SAE J2249) in accordance  with the WTORS manufacturer’s instructions.
4. The wheelchair’s use in other positions within a vehicle has not been tested e.g. transportation in a side facing position must not be carried out under any circumstances (Fig. A).
5. The wheelchair should be secured by a Tie Down Restraint system, conforming to ISO 10542 or SAE J2249 with nonadjustable front straps and adjustable rear straps, which typically use Karabiner clips/S hooks and tongue and  buckle fittings. These restraints generally comprise of 4 individual straps that are attached to each corner of the wheelchair.
6. The tie-down restraints should be fitted to the main frame of the wheelchair as indicated in the diagram on the following page, and not to any attachments or accessories, e.g. not around the spokes of wheels, brakes or footrests.
7. The tie–down restraints should be attached as close as possible at an angle of 45 degrees and tightened securely in accordance with the manufacturer’s instructions.
8. Alterations or substitutions must not be made to the wheelchair securement points or to structural and frame or components without consulting the manufacturer. Failure to do so will invalidate the ability of a Sunrise Medical  wheelchair to be transported within a vehicle.
9. Both pelvic and upper torso restraint belts must be used to restrain the occupant to reduce the possibility of head and chest impacts with the vehicle components and serious risk of injury to the user and other vehicle occupants. (Fig  B) The upper torso restraint belt should be mounted to the vehicle “B” pillar – failure to do so will increase the risk of serious abdominal injuries to the user.
10. A head restraint suitable for transportation (see label on headrest) must be fitted and suitably positioned at all times during transportation.
11. Postural supports (lap straps, pelvic restraint belts) should not be used or relied on for occupant restraint in a moving vehicle unless they are labelled as meeting the requirements specified in ISO 7176-19 or SAE J2249.
12. The safety of the user during transportation depends upon the diligence of the person securing the tie-down restraints and they should have received appropriate instructions and/or training in their use.
13. Wherever possible remove and stow safely away from the wheelchair all auxiliary equipment, for example: Crutches, Loose cushions and Tray Tables.
14. Articulating/elevating leg rest should not be used in the elevated position when the wheelchair and user are being transported and the wheelchair is restrained using Wheelchair Transport and Occupant Restraints.
15. Reclining backrests should be returned to an upright position.
16. The manual brakes must be firmly applied.
17. Restraints should be mounted to the vehicle “B” pillar and should not be held away from the body by wheelchair components such as armrest or wheels.

Transportability

Occupant Restraints Instruction:

1. The pelvic restraint belt must be worn low across the front of the pelvis so that the angle of the pelvic belt is within the preferred zone of 30 to 75 degrees to the horizontal.
   A steeper (greater) angle within the preferred zone is desirable i.e. closer to, but never exceeding 75 degrees. (Fig C)

2. The upper torso restraint belt must fit over the shoulder and across the chest as illustrated Fig d and Restraint belts must be adjusted as tightly as possible consistent with user comfort.
   Restraint belt webbing must not be twisted when in use.
   The upper torso restraint belt must fit over the shoulder and across the shoulder as illustrated in Fig D and E.

3. The attachment points to the chair are the inner front side frame just above the castor, and the rear side frame. The straps are fitted around the side frames at the intersection of the horizontal and vertical frame tubes. (See Figs G- H-I)

4. The tie down symbol (Fig F) on the wheelchair frame indicates the position of the wheelchair restraint straps. The straps are then tensioned after the front straps have been fitted to secure the wheelchair.

DANGER!
USER WEIGHT LESS THAN 22 kg (48 lb 8.0 oz)
When the user being transported is a child, less than 22Kg mass and the vehicle involved has less than eight (8) seated passengers it is recommended that they be transferred to an UNCE Regulation 44 compliant child restraint system  (CRS). This type of restraint system provides a more effective occupant restraint system than the conventional 3 point occupant restraint system and some CRS systems also include additional postural supports to assist in maintaining the position of the child when seated.
Parents or care providers may consider the option, in some circumstances, for their child is to remain in their wheelchair whilst in transport due to the level of posture control and comfort provided by the set up in the wheelchair.
We would recommend in such circumstances that a risk assessment be carried out by your healthcare professional and relevant competent persons.

Transportability – positioning of wheelchair tie down restraints on wheelchair
The wheelchair secured with front and rear wheelchair tie down restraints, (Fig.K).
Position of the front wheelchair tie down restraint and the tie down position, (Fig.I).
Position of the rear wheelchair tie down restraint and the tie down position on the wheelchair, (Fig.J).

Handling

Folding up
First remove the seat cushion from the wheelchair and flip up the (platform) footplate. Take hold of the sling or the seat tubes (Fig. 4.1) in the middle, from the back, and pull it upwards until the folding bracket (Fig. 4.2) clicks into place.

Transportation
To move the mobility aid, the folded wheelchair should be lifted by holding the front part of the cross-brace and the push handles.

Unfolding
Push the release lever of the folding bracket (Fig. 4.3) downwards and push both frame halves apart. Then press on the seat tube (see figure). Your wheelchair is then unfolded. Now snap the seat tubing into position in the seat saddle.  This can be facilitated by slightly tipping your wheelchair to the side (Fig. 4.4), as this means that the weight is taken off one of the rear wheels.
Be careful not to get your fingers caught in the crosstube assembly. Fit the seat cushion.

Transporting the Wheelchair
When transporting the unoccupied wheelchair in a vehicle, it should be tied down or strapped in.

Getting into your wheelchair on your own (Fig. 4.5)

• Push the wheelchair to a wall or a solid piece of furniture
• Apply the brakes
• Flip the footplates up
• The user can lower themselves into the wheelchair
• Fold the foot plates back downwards and position your feet in front of the heel loops.

Getting out of your wheelchair on your own

• Apply the brakes
• Fold the footplates upwards with your foot
• With one hand on the armrest, the person should bend slightly forward, to bring the body weight to the front of the seat, and then with both feet firmly on the ground and one foot behind the other, push up into the upright position Fig. 4.6

Quick-Release Axles for Rear Wheels (Fig. 4.7)
The rear wheels are equipped with quick-release axles. The wheels can thus be installed or removed with out using tools. To remove a wheel, simply depress the quick-release button on the axle (1) and pull it out.

CAUTION!
Hold the quick-release button on the axle depressed when inserting the axle into the frame to mount the rear wheels.
Release the button to lock the wheel in place. The quick-release button should snap back to its original position.

Quick-Release Axles for Casters (Fig. 4.8)
Casters can also be equip ped with quick-release axles (1), which can then either be installed or removed without using tools. Fig. 4.8

Options

Tipping Tubes
Tipping Tubes (Fig. 5.01)
Tipping tubes are used by attendants to tip a wheelchair over an obstacle. Simply step on the tube to push a wheel chair, for example, over a curb or step.

Wheel locks
Wheel Locks
Your wheelchair is equipped with two wheel locks. They are applied directly against the tires.
To engage, press both wheel-lock levers forward against the stops (Fig. 5.02 and 5.04). To release the wheel, pull the levers back to their original positions.
Braking power will decrease with:
Knee-lever brake

• Worn tire tread
• Tire pressure that is too low
• Wet tires
• Improperly adjusted wheel locks.
  Knee-lever brake

The wheel locks have not been designed to be used as brakes for a moving wheelchair. The wheel locks should therefore never be used to brake a moving wheelchair. Always use the handrims for braking. Make sure that the interval between the tires and wheel locks complies with given specifications (Fig. 5.03 and 5.05). To readjust, loosen screw (1) and set the appropriate interval. Tighten screw (see the page on torque)

Standard brake

CAUTION!
After each adjustment of the rear wheels, check the interval to the wheel locks and readjust if necessary.

Extension for the Brake Lever (Fig. 5.06)
The extension for the brake lever can be removed or folded down.
The longer lever helps to minimize the effort needed to set the wheel locks.
CAUTION!

• Mounting the wheel lock too close toward the wheel will result in a higher effort to operate. This might cause the brake lever extension to break!
• Leaning onto the brake lever extension while transferring will cause the lever to break! Splashing water from tires might cause the wheel lock to malfunction.

Drum Brakes (Fig. 5.07)
Drum brakes permit safe and convenient braking for an attendant. They can also be set with the aid of a locking lever (1) to prevent rolling. This lever must snap audibly into place. Drum brakes do not independent on the aid of air pressure inside the tires. Your wheelchair cannot be moved when the drum brakes are set.

CAUTION!
Drum brakes should only be adjusted by authorized dealers.

One Hand Wheel Locks
Your wheelchair is equipped with two sets of wheel locks, that operate from the left or the right side. They are applied directly against the tires. To engage, press the wheel-lock lever forward against the stop (Fig. 5.08). To release the  wheel, pull the lever back to the original position.

Braking power will decrease with:

• Worn tire tread
• Tire pressure that is too low
• Wet tires
• Improperly adjusted wheel locks.

The wheel locks have not been designed to be used as brakes for a moving wheelchair. The wheel locks should therefore never be used to brake a moving wheelchair. Always use the handrims for braking. Make sure that the interval between the tires and wheel locks complies with given specifications. To readjust, loosen screw and set the appropriate interval. Tighten screw (see the page on torque).

CAUTION!
After each adjustment of the rear wheels, check the interval to the wheel locks and readjust if necessary.
CAUTION!
Mounting the wheel lock too close toward the wheel, will result in a higher effort to operate. This might cause the brake lever extension to break! Leaning on to the brake lever extension while transfering will cause the lever to break!  Splashing water from tires might cause the wheel lock to malfunction.

Compact wheel lock
Compact wheel locks are underneath the seat sling and are operated by pulling the wheel locks towards the rear, in the direction of the tyre. For the wheel locks to operate correctly, they must be pulled fully against the stops, (Fig. 5.10).
CAUTION!
Incorrect mounting of the wheel lock will result in a higher effort to operate.

Footplates (Fig. 5.11)
There are two types of footplates: platform and divided. They can be flipped up to facilitate getting in and get ting out of your wheelchair.
Lower Leg Length
Footplates
By removing the setscrews (1), the footrest can be adjusted to fit any lower leg length. Remove setscrews, set tubing with footrest in the desired position, and reinsert and tighten the setscrews (see the page on torque).
Make sure that the compo site plastic pad is in the proper position under the setscrew. A minimum interval of 25mm from the ground should always be maintained.

Width Adjustment of the footrests
If the footrest width needs to be adjusted, please undo the screw (1), set the desired width, by positioning 1, 2 or 3 spacers (2) from outer to the inner side and then refit the screws, (Fig. 5.12).

Footboard lock
The footplate locks in automatically when flipped down.
To flip it up the release knob (1) must be pulled. To keep the unlocked position turn knob 1 when it is pulled (Fig. 5.13).
WARNING!
Always make sure to unlock the system to get full functionality!

Divided and Platform Footplates (Fig. 5.14 – 5.15)
Footplates can be flipped up to facilitate getting in and getting out of your wheelchair.
They can also be tilted to six different angles relative to a level surface. Tighten screw (1) firmly on the outer side. By removing the clips (2), the footplate can be adjusted to three different positions toward both the front and rear. For this  purpose, the footplate must be flipped up.
When finished, make sure that all screws have been properly tightened (see the page on torque).
A minimum interval of 25 mm from the ground should always be maintained.

Footrests

Various footboards are available.
These can be flipped up to make it easier to transfer to/from the chair. They are described individually.

Footrest and swing away latch
When fitting the footrests these are fitted in the swung-away position (Fig. 5.17). Then simply turn them inwards until the interlock engages (1). To remove the footrests, use the lever (2) and swing the footrest outwards and lift off. Check  that the footrest is correctly engaged.

WARNING!
The footrests are not designed to be used to lift or carry the wheelchairs with an occupant.
Hanger play adjustment
In case of play the hanger (Fig. 5.18) can be adjusted in the field. The hanger pin (1) is tapered and the play can be reduced when the pin is unscrewed slightly.
Take the hanger off the chair in using the release mechanism.
Use an screw driver and turn the pin (1) in the front carefully to the left. Then test the hanger on the chair. If the hanger mechanism is not working/catching anymore, please undo the task slightly.
If the play is still too large and the performance not accepted, please repeat the task.

Lower leg lengths
By undoing the clamp screw (Fig. 5.19), you can adjust the lower leg length. Loosen the clamp screw, adjust the tube with the footboard to the desired position.
Tighten clamp screws again (see the page on torque). Ensure that the plastic push joint is located under the clamp screw in the correct position.

WARNING!
Do not stand on the footboard!
When transferring, do not stand on the footboard, there is a risk of tipping over and injury.

High-Mount Footrest (Fig. 5.20 – 5.20.1)
The footplates can be flipped up to facilitate getting in and out of your wheelchair.
The footplates can be adjusted within their angle of inclination, relative to a level surface. Loosen the screws (1 to 2). Then set the footplates to the desired angle. Afterwards, tighten all screws. After adjustment, always make sure that all  screws are tightened properly (see the page on Torque). In order to avoid the wheelchair tipping over, make sure that the minimum interval of 25mm between the foot rest tubing and the ground is maintained (with horizontal seat).

Automatic folding footrest
The footrest angle can be adjusted by loosening the screws (1) and turning the footrest. When tightening, please note the torque measurements, (Fig.5.20.2).

Option Elevating legrest (Fig.5.20.3 – 5.20.5)
To remove, pull the lever (1), swing the footplate outwards and then lift the legrest out.
Height Adjustment:
The lower leg length can be adjusted infinitely by releasing the screw (2). Adjust the suitable height and tighten the screw again.
CAUTION!
The distance between the footplate and the ground must be at least 40 mm.
Angle Adjustment:
Press the lever (3) downward with one hand while supporting the legrest with the other hand to take the load off. When a suitable angle is achieved, let go of the lever and the legrest will lock into one of the preset positions.
WARNING!

• Keep hands clear of the adjustment mechanism between the frame and the movable parts of the footrest while elevating or lowering the footrest.
• The footrests should not be used to lift or to carry the wheelchair.
• Risk of trapping fingers!
• When moving the footrest up or down, do not put your fingers in the adjusting mechanism between the moving parts of the footrest.

Lightweight footrest
The footrest angle can be adjusted by loosening the screws (2). Side protection panels can be fitted to the footrest using the mounting holes (3). These prevent the feet slipping off accidentally, (Fig. 5.20.6). Make sure that after any  adjustment work, all screws are tightened correctly (see the page on torque).

Headrest
Headrest (Fig. 5.21)
The headrest can be raised and moved both forwards and backwards. To do this, simply loosen the screw (1 or 2), adjust to the desired posi tion, and tighten the screw (see the page on torque).

Casters
Casters, Caster Plates, Forks (Fig. 5.22)
The wheelchair may veer slightly to the right or left, or the casters may wobble. This may be caused by the following:

• Forward and/or reverse wheel motion has not been set properly.
• The camber has not been adjusted properly.
• Caster and/or rear wheel air pressure is incorrect; wheels do not turn smoothly.

The wheelchair will not move in a straight line if the casters have not been properly ad justed. Casters should always be adjusted by an authorized dealer. The caster plates must be readjusted, and the wheel locks must be checked any time the rear wheel posi tion has been altered.

Axle Plates
Axle Plates (Fig. 5.23)
The position of the body’s center of gravity with respect to the rear wheels is critical for ensuring easy and pleas ant use of the wheelchair. Several positions are possi ble: moving the axle plate (1) backwards along the holes drilled in the frame (2) will make the chair more stable, but it will not be as maneuverable as it would be if the axle plate were positioned farther to the front. You may adjust the seat height by moving the axle sleeve (3) in the axle plate. When finished, make sure that all screws have been properly tightened (see the page on torque).
CAUTION!
It may be necessary to readjust both the heel locks and casters.

Cambers
Cambers (Fig. 5.24 – 5.25)
The camber may be set between 1° and 4°. This makes it possible to increase the chair’s lateral stability as well as its maneuverability. Remove the axle plate screws (1). Adjust the adap ter (2) to the desired angle. Tighten the screws. (see  the page on torque). Raising the camber also raises the overall width of the wheelchair (by about 10mm per degree).
CAUTION!
It may be necessary to readjust both the wheel locks and casters.

Amputee Axle Plate
Amputee Axle Plate (Fig. 5.26 – 5.27)
The larger the wheel base is, the greater is the stability of the wheelchair. The wheel base can be extended by screwing the axle sleeve (1) onto the frame at the desired height. Make sure that the steel pin (2) is mounted correctly in the hole drilled in the frame for this purpose. When finished, make sure that all screws have been properly tightened (see the page on torque).
CAUTION!
Wheel locks must be ad justed for the new position.

Backrests
Backrest angle
Undo the screw A and pull the screw out of its position. Set the desired angle and then re-tighten the screw.
Make sure that the angle is set the same on both sides. Please observe the Nm torque value (see the page on torque).

Variable Angle-Adjustable Backrests (Fig. 5.29)
You can adjust the angle of the backrest to meet your individual needs by pulling on the cord (1). The mechanism automatically snaps into place when you release the cord.

Adjustable Backrest Upholstery (Fig. 5.30)
The sling can be adapted to any degree of tension by adjusting the Velcro fasten ers, (1). The padding in the backrest can be removed through an interior  opening, allowing you to cushionthe backrest according to your individual needs.

Sideguards

Tool Height Adjustable Armrest
Installation: Slide the arm post into the receiver, located on the wheelchair frame, until it stops
Height adjustment:
Slide the arm rest post out of the receiver.
Adjust the position of the hight adjustment bracket (1) by removing the screw (2) and moving it to the desired posiion. Re-fit the screw and tighten it.
Slide the arm rest post back into the receiver, (Fig.5.31).
Armpad Position:
The armpad position can be adjusted by relesing the screws (3), then moving the arm pad to the desired position. Re-tighten the screws, (Fig.6.24).
Adjusting Armrest Receiver
The tightness of the armrest receiver can be adjusted (tightened/loosened) by means of the 2 screws (1) – (Fig.5.32).
Sideguard With Clothes Protector (Fig.5.33)
The clothes protector prevents clothes getting dirty from spray water. You can set the position in relation to the rear wheel by moving the sideguard.
To do this, remove the fixing screws (1 and 2).
After setting to the desired position, re-tighten the screws (see the page on torque).
WARNING!
Neither the sideguards nor the armrests are to be used for lifting or carrying the wheelchair

Sideguards – Clothing Guards (Fig.5.34)
Clothing guards prevent water from splashing up and soiling clothing. Their position relative to the rear wheels can be set by adjusting the sideguards. To do this, remove the screws (1 and 2).
After adjusting the sideguards to the desired position, replace and retighten the screws (see the page on torque).

WARNING!
Neither the sideguards nor the armrests are to be used for lifting or carrying the wheelchair.

Sideguard, Aluminum, Bolt-On with Cold-Weather Protection (Fig. 5.35)
Clothing guards (optional) prevent water from splashing up and soiling clothing.
Their position relative to the rear wheels can be set by adjusting the sideguards.

To do this, remove the screws (1 and 2). The armrests (optional) can be adjusted to the desired height after the screws (3) have been removed. When finished, make sure that all screws have been properly tightened (see the page on  torque).

WARNING!
Neither the sideguards nor the armrests are to be used for lifting or carrying the wheelchair.

Options – One Hand Operation

One Hand Operation (Fig. 5.36 – 5.36.1)
To propel the chair straight forward both handrims must be used. To fold the wheelchair disconnect the telescopic bar by pushing it inward (1). To take off the wheels, press the locking button on the axle (2).
CAUTION!
Make always sure that the connections are set properly to avoid injuries.

Push Handles

Height-Adjustable Push Handles (Fig. 5.37)
These handles are secured with pins to prevent them from sliding out unintentionally. Opening the quick-release lever (1) makes it possible to adjust the push handles to meet your individual needs. As you move the lever, you will hear a  locking mechanism; you may now easily position the push handle as desired. The nut (2) on the tension lever determines how tightly the push handles are clamp ed into place. If the nut is loose after adjusting the tension lever, the push  handle will also be too loose. Turn the push handle from side to side before use to make sure that it is clamped securely enough into place. After adjusting handle height, always clamp the tension lever (1) securely into place. If the lever is  not secure, injuries could result when lifting over obstacles.

Fold-Down Push Handles (Fig. 5.38)
If the push handles are not in use, they can be folded down by depressing the button (2). When they are needed again, simply flip them back up until they click into place.

Pelvic Restraint Belt
DANGER!

• Before using your wheelchair ensure the pelvic restraint belt is worn.
• The pelvic restraint belt must be checked on a daily
• basis to ensure it is free from any obstruction or adverse wear.
• Always make sure that the lap strap is correctly secured and adjusted prior to use. If the strap is too loose it could cause the user to slip down and risk suffocation or cause serious injury.
  The pelvic restraint belt is fitted to the wheelchair as shown in the illustrations. The seat belt comprises 2 halves. They are fitted using the existing seat stay retaining bolt fitted through the eyelet on the belt. The belt is routed under  the rear of the side panel. (Fig. 5.39)
  Adjust the belt position so buckles are in the centre of the seat. (Fig. 5.40)

Adjust pelvic restraint belt to suit the user’s needs as follows:

When fastened check space between the pelvic restraint belt and user. When correctly adjusted it should not be possible to insert more than the flat of the hand between the pelvic restraint belt and the user. (Fig. 5.41)

Pelvic Restraint Belt…
The pelvic restraint belt should be fixed so that the belt sits at an angle of 45 degrees across the user’s pelvis. The user should be upright and be as far back as possible in the seat when correctly adjusted. The pelvic restraint belt should not allow the user to slip down in the seat. (Fig. 5.42)

Anti-Tip Tubes
Anti-Tip Tubes (Fig. 5.43)
Anti-tip tubes (1) provide additional safety for inexperienced users when they are still learning how to operate their wheelchairs. Anti-tip tubes (1) prevent a wheelchair from tipping over backwards. Pushing the anti-tip tubes (1) will move them downwards; they can also be swung forward. An interval of 30mm to 50mm should be maintained between them and the ground. You must swing the anti-tip tubes forward when going up and down large ob stacles (such as a curb)  to prevent them from touching the ground.

Standard Sling

Standard Sling (Fig.5.44)
The sling is equipped with a Velcro fastener on one side; this permits stepless adjustment of the sling. To readjust the sling, first fold up the wheelchair slightly. Then remove the screws (1) and pull the front plugs (2) forward out of the  frame. The sling (3) can then be slid off of the frame. By unfastening the Velcro, the sling can be readjusted. Reverse this pro cedure to reinstall the sling. When finished, make sure that all screws have been properly tightened (see the  page on torque).
WARNING!
For proper safety, at least 50 % of the Velcro surfaces must make contact with each other at all times.

Crutch Holder
Crutch Holder (Fig. 5.45) This device permits crutches to be transported directly on a wheelchair. It has a Velcro loop (1) to fasten crutches or other aids.

WARNING!
Never try to use or even remove the crutches or other aids while moving.

Tray
Tray (Fig. 5.46)
The tray provides a flat surface for most activities. Before using a tray, it first has to be adjusted once to the width of the seat by an authorized dealer. The user must be sitting in the wheelchair during the trial run.

Stabilising bar
Folding stabilising bar This bar is used to stabilise the backrest. To be able to fold the wheelchair, the release lever must be pushed inwards (Fig. 5.47) or released and the stabilising must be flipped downwards. When unfolding the wheelchair, please make sure that the stabilising bar is locked into position.

Transit Wheels
Transit Wheels (Fig. 5.48)
Transit wheels should be used wherever your wheelchair would be too wide if the rear wheels were used (e.g., in airplanes, buses, etc.). After the rear wheels have been removed with the aid of the quick-release axles, the transit wheels can immediately be used to continue riding. The transit wheels are mounted so that they are approx. 30mm above the ground when not in use. They are thus out of the way when riding, transporting, or when tipping to pass over obstacles  (e.g., curbs, steps, etc.).
WARNING!
Your wheelchair does not have any wheel locks when the transit wheels are being used.

Daily Checks

CAUTION!
As the user, you are the first person to notice any possible defects. We therefore recommend that before each use, you check the items in the following list:

• Check for correct tyre pressures.
• Check that the brakes work correctly.
• Check that all removable parts are secure, e.g. armrest, footrest, quick-release axle etc.
• Check for visible damage e.g. on the frame, backrest, seat sling and back sling, wheels, footplate etc.
  If there is any damage or malfunction, please contact your authorised dealer.

Tyres and mounting

WARNING!
Always make sure that you maintain the correct tyre pressure (min. 3.5 bar) as this can have an effect on wheelchair performance.
If the tyre pressure is too low, rolling resistance will increase, requiring more effort to move the chair forward. Low tyre pressure also has a negative impact on maneuverability.
WARNING!
If the tyre pressure is too high, the tyre could burst. The correct tyre pressure for a given tyre is printed on the surface of the tyre (min. 3.5 Bar).
Tyres can be mounted the same way as an ordinary bicycle tyre.
Before installing a new inner tube, you should always make sure that the base of the rim and interior of the tyre are free of foreign objects.
Check the pressure after mounting or repairing a tyre.
It is critical to your safety and to the wheelchair’s performance that regulation air pressure be maintained and that tyres are in good condition.

Maintenance and Care

• Check the tyre pressure every 4 weeks. Check all tyres for wear and damage.
• Check the brakes approximately every 4 weeks to make sure that they are working properly and are easy to use.
• Change tyres as you would an ordinary bicycle tyre.
• All of the joints that are critical to using your wheelchair safely are self-locking nuts. Please check every three months to make sure that all bolts are secure (see the section on torque). Safety nuts should only be used once and should  be replaced after use.
• Please use only mild household cleansers when your wheelchair is dirty. Use only soap and water when cleaning the seat upholstery.
• You should only use genuine parts approved by Sunrise Medical. Do not use parts from other manufacturers, that have not been by authorised by Sunrise Medical.
• If your wheelchair should ever get wet, please dry it afterwards.
• A small amount of sewing-machine oil should be applied to quick-release axles approximately every 8 weeks. Depending on the frequency and type of use, we recommend taking your wheelchair to your authorised dealer every 6  months to have it inspected by trained personnel.
• If you want to store the wheelchair for a long period of time, then no further measures are required. Make sure that the wheelchair is stored at room temperature in a dry place which is protected from strong sunlight. Before using it
  again, the wheelchair should be checked by an authorised dealer.

CAUTION!
Sand and sea water (or salt in the winter) can damage the bearings of the front and rear wheels. Clean the wheelchair thoroughly after exposure.
The following parts can be removed and sent back to the manufacturer/dealer for repair:

• Rear wheels
• Armrest
• Anti-Tip tubes

These components are available as spare parts. For further information, please see the spare parts catalogue.
Hygiene measures when being re-used:
Prior to the wheelchair being re-used, it must be carefully prepared. All surfaces which come into contact with the user must be treated with a disinfection spray.
To do this, you must use a disinfectant as authorised/recommended in your country, for rapid alcohol-based disinfection for medical products and medical devices, which must be disinfected quickly.
Please be aware of the manufacturer’s instructions for the disinfectant you are using.
In general, a complete disinfection cannot be guaranteed on seams. We therefore recommend that you dispose of seat and back slings to avoid micro- bacterial contamination with active agents according to your local infection protection law.

Trouble shooting

Wheelchair pulls to one side

• Check tyre pressure
• Check to make sure wheel turns easily (bearings, axle)
• Check the castor angle
• Check to make sure both casters are making proper contact with the ground

Casters begin to wobble

• Check the castor angle
• Check to make sure all bolts are secure; tighten if necessary (see the section on torque)
• Check to make sure both casters are making proper contact with the ground

Wheelchair / Cross-tube assembly does not snap into position in the seat saddle

• Chair is still new, i.e., the seat or backrest upholstery is still very stiff. This will improve with time Wheelchair is difficult to fold up
• Adjustable backrest upholstery is too stiff. Loosen it accordingly.

Wheelchair squeaks and rattles

• Check to make sure all bolts are secure; tighten if necessary (see the section on torque)
• Apply small amount of lubrication to spots where movable parts come in contact with one another

Wheelchair begins to wobble

• Check angle at which castors are set
• Check tyre pressure
• Check to see if rear wheels are adjusted differently

Disposal/Recycling of Materials

NOTE: If the wheelchair has been mde available to you as part of a charity or medical loans scheme, then it may not belong to you. If it is no longer required, then follow the instructions to return it as given by the organisation that made  the wheelchair available to you.
In the following section, there is a description of the materials used on the wheelchair, in view of the disposal or recycling of  the wheelchair and its packaging.
There may also be special local regulations in force with regard to disposal or recycling, these must be taken into account when disposing of your wheelchair. (This can include the cleaning or decontamination of the wheelchair prior to  disposal). Aluminium: Castor forks, wheels, sideguards for the chassis, armrest frame, footrest, push handles
Steel: Fixing points, quick-release axle
Plastic: Handles, tube stoppers, castors, footplates, armpads and 12” wheel/tyre
Packaging: Plastic bags made of soft polyethylene, cardboard Upholstery: Woven polyester with PVC coatings and expanded combustion modified foam.
Disposal or recycling should be done through a licensed agent or authorised place of disposal. Alternatively your wheelchair may be returned to your dealer for disposal.

| Product Name/SKU Number.
---|---
Maximum safe slope with anti-tip tubes fitted, Depends on wheelchair setting.
Seat width.
Seat depth.
Load Maximum.
UKCA Mark.
CE Mark.
Consult instructions for use.
Date of manufacture.
Serial number.
This symbol means Medical Device.
Manufacturer’s address.
Crash tested according to ISO 7176-19:2008.
Importer’s address
UK Responsible Person
Swiss Representative’s address

Technical Data – Possible seat-height adjustments

Technical Data

Technical Data (Easy 200-300)
Total width: with standard wheels, incl. Hand rims, close mounted

• in combination with desk sideguards: SW + 200 mm
• in combination with aluminium sideguards: SW + 180 mm
• in combination with clothing protection, composite: SB + 190 mm
• A super-narrow handrim attachment reduces the overall width by 20 mm
• Wheels with drum brakes widen the chair by 20 mm

Dimensions, folded:

• without rear wheels: approx. 200 mm
• with rear wheels: approx. 250 mm

Weight in kilogramms:

• Footrests Easy 300: 1,35 kg
• Footrests Easy 200: 0,93 kg
• Chair with no sideguards, footrests or rear wheels: 7,60 kg
• Desk-Sideguards: 3,10 kg

Maximum weight limit:

• Approved for user weights up to 140 kg (136kg crash tested)
• With Light-weight Wheel = 125 kg
• With Proton Wheel = 100 kg
• With Hand Bike = 100 kg

Seat Heights
The choice of frames, forks and castors, as well as the rear wheel size (24”, 25”) determines the seat heights which can be achieved.

The wheelchair conforms to the following standards:

a) Requirements and tests for static strength, impact resistance and fatigue strength (ISO 7176-8)| Yes.
---|---
b) Drive and control systems for power wheelchairs, requirements and test (ISO 7176-14)| n.a.
c) Environmental test in accordance with ISO 7176-9| n.a.
d) Flammability resistance of upholstered parts in accordance with ISO 7176-16 (EN 1021-1/2)| Yes.

Sunrise Medical
Thorns Road
Brierley Hill
West Midlands
DY5 2LD
England
Phone: 0845 605 66 88
Fax: 0845 605 66 89
www.SunriseMedical.co.uk

Documents / Resources

| QUICKIE EASY 200/300 Wheel Chair [pdf] Instruction Manual
EASY 200 300 Wheel Chair, EASY 200 300, Wheel Chair, Chair
---|---

References

• Kørestole, rollatorer, siddesystemer | Sunrise Medical
• Haltija
• Oficiální stránky společnosti Medicco s.r.o. | Sunrise Medical
• Wózki manualne, elektryczne i dzieciÄ™ce. | Sunrise Medical
• Rollstühle, Elektromobile und Sitzsysteme | Sunrise Medical
• Wheelchairs, Seating & Mobility Scooters | Sunrise Medical
• Wheelchairs, Mobility Scooters & Custom Seating | Sunrise Medical
• Rollstühle, Rollstuhlzubehör & Elektromobile | Sunrise Medical
• Kørestole, rollatorer, siddesystemer | Sunrise Medical
• Wheelchairs, Mobility Scooters, Rollators | Sunrise Medical
• Carrozzine, postura e ausili per la mobilità | Sunrise Medical
• Rolstoelen | Zitkussens | Scootmobielen | Sunrise Medical
• Hjem | Sunrise Medical
• Rullstolar, sittande & scooter | Sunrise Medical

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>