PROSCEND 850G-10PI Industrial Ethernet Switch Installation Guide

PROSCEND 850G-10PI Industrial Ethernet Switch

Product Information

850G-10PI Industrial Ethernet Switch

The 850G-10PI Industrial Ethernet Switch is a high-performance switch designed for industrial environments. It supports two power
supplies with an input range of 48~57 VDC. The switch features LED indicators for power, alarm, LAN port status, UPLINK, and PoE. It also includes an alarm relay output and supports DIN-rail mounting.
The switch is equipped with RJ45 connectors and supports various pinouts for PoE connectivity. The DIP switch allows for easy configuration of power alarm reporting, broadcast storm control, port priority, and Port 100FX support. The switch also includes a reset button for rebooting or resetting to factory defaults.

Specifications

• Input Voltage: 48~57 VDC
• Power Supply: Two power supplies
• LED Indicators: PWR/RPS, ALM, RJ45 LAN port Link/Act, RJ45 LAN port Speed, UPLINK, PoE
• Alarm Relay Output: Normal Open, 1A @ 24 VDC
• DIN-rail Mounting: Yes
• RJ45 Connector Pinouts: T/Rx+, T/Rx-, V+, V-, X

Product Usage Instructions

Connecting Power

To connect power to the switch, follow these steps:

1. Insert the positive and negative wires (AWG 12-24) into V+ and V- contacts on the terminal block respectively.
2. Use a flat-head screwdriver to push in and open the wire clamp.

Alarm Relay and Ground

The alarm relay output contacts are shown as ALM next to the DC terminal block connector. The relay is Normal Open and will be closed when detecting any predefined failure such as power
failures. The switch must be properly grounded for optimum system performance.

LED Indicators

(alarm for abnormal power status or function), Off: Green
RJ45 LAN port Link/Act| On: Green (Ethernet LINK UP), Blinking: Green (Ethernet traffic
detected), Off: Green (Ethernet LINK DOWN)
RJ45 LAN port Speed| On: Green (Ethernet LINK UP at 1000Mbps), Blinking: Green
(Ethernet LINK DOWN or LINK UP at 10Mbps/100Mbps), Off: Green (LINK
DOWN)
UPLINK| On: Green (PoE PD connected), Blinking: Green (PoE PD
disconnected), Off
PoE| On: Green (PoE PD connected), Off (PoE PD disconnected)

RJ45 Connector Pinouts

The pin assignment of the RJ45 connector is as follows:

DIN-rail Mounting

To mount the switch on a DIN-rail, follow these steps:

1. Use the screws to install the DIN-rail kit at the rear side of the switch.
2. Hook the unit onto the DIN-rail.
3. Push the bottom of the unit towards the DIN-rail until it locks in place.

DIP Switch Setting

The DIP switch allows for easy configuration of various settings. The functions and descriptions are as follows:

Reset Button

The reset button can be used to reboot the switch or reset it to factory defaults. Follow these instructions:

• Reboot: Press the Reset button for 2 seconds and release.
• Reset to factory default: Press the Reset button for 10 seconds and release.

Web Interfac e: Connect & Login

To access the web interface, follow these steps:

1. Factory default IP: 192.0.2.1
2. Login with default account and password:

NOTE: Please scan the provided QR Code to download online resources.

Download Link: https://www.proscend.com/en/product/850G-10PI.html

Proscend Communications Inc. All rights reserved.

850G-10PI Industrial Ethernet Switch Quick Installation Guide

Connecting Power

The 850G-10PI Industrial Ethernet Switch can be powered from two power supplies (input range 48~57 VDC). Two power supplies are on the top panel of the switch. Insert the positive and negative wires (AWG 12-24) into V+ and V- contacts on the terminal block respectively and use a flat-head screwdriver to push in and open the wire clamp.

Alarm Relay and Ground

• The alarm relay output contacts are shown as ALM next to the DC terminal block connector as the figure below.
• The alarm relay out is “Normal Open”, and it will be closed when it is detecting any predefined failure such as power failures.
• The relay output with current carrying capacity of 1A @ 24 VDC.
• The switch must be properly grounded for optimum system performance.

DIP Switch Setting

1 (PWR)

2 (RPS)

| ON: Power alarm reporting is enabled. OFF: Power alarm reporting is disabled.
3 (Storm)| ON: Broadcast storm control is enabled.
OFF: Broadcast storm control is disabled.
4 (QoS)| ON: Port Priority is enabled on Port 2.
OFF: Port Priority is disabled.
5 (Port 9)

6 (Port 10)

| ON: Port 100FX support is enabled. OFF: Port 100FX support is disabled.

DIP Switch Setting

LED Indicators

Blinking:

Green

| Ethernet traffic detected.
Off| Ethernet LINK DOWN.
RJ45 LAN port Speed| On: Green| Ethernet LINK UP at 1000Mbps.
Off| Ethernet LINK DOWN or LINK UP at

10Mbps/100Mbps

UPLINK| On: Green| LINK UP.
Blinking:

Green

| Traffic detected.
Off| LINK DOWN.
PoE| On: Green| PoE PD (Powered Device) connected.
Off| PoE PD (Powered Device) disconnected.

RJ45 Connector Pinouts

The pin assignment of RJ45 connector is shown in the following table.

DIN-rail Mounting

STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side of the switch.

STEP 2: Hook the unit onto the DIN-rail.

STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in place.

Web Interface: Connect & Login

1. Factory default IP: 192.0.2.1
2. Login with default account and password. Username: root Password: 2wsx#EDC

NOTE
Please scan below QR Code to download online resources. Download Link:
https://www.proscend.com/en/product/850G-10PI.html

850G-10PI

References

• PROSCEND is a leading global provider of mission-critical Internet of Things (IoT) connectivity products, services, and solutions with high levels of reliability and security.
• PROSCEND is a leading global provider of mission-critical Internet of Things (IoT) connectivity products, services, and solutions with high levels of reliability and security.
• Industrial 10-Port GbE Managed PoE Switch | Industrial 5G Cellular Router Manufacturer | PROSCEND

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>