velleman K8110 Tremor Tremolo Effect Pedal Instruction Manual

June 12, 2024
Velleman

velleman K8110 Tremor Tremolo Effect Pedal

velleman K8110 Tremor Tremolo Effect Pedal

Let’s get started!

velleman K8110 Tremor Tremolo Effect Pedal

WHAT’S IN THE BOX

What’s In The Box

ASSEMBLY INSTRUCTIONS

  1. Place the 2 supplied cover stickers as shown in the images below. Note the orientation of the bottom cover!
    Assembly Instructions
    Assembly Instructions

  2. All resistors are placed in the correct order of usage on the supplied tape. Resistors: R1 to R19
    Assembly Instructions

Tape order:| R12:4K7
R13:47K
---|---
R1:330K| R14:33K
R2:470K| R15:10K
R3:330K| R16:39K
R4:470K| R17:100K
R5:390E| R18:100E
R6:10K| R19:1M
R7:100K| C3:104
R8:470E| C4:104
R9:470E| C9:104
R10:1M| ZD1:3V3
R11:10K| D1:1N4007

Assembly Instructions

  1. 100 µF axial capacitors: C3, C4 and C9
    Assembly Instructions

  2. 2 x Ic: U1 and U2
    Note the orientation of the Ic’s!
    Assembly Instructions

  3. Zener diode: ZD1
    Note the orientation of the Zener diode!
    Assembly Instructions
    Assembly Instructions

  4. . Male connectors: SW1; SW2, RV1; RV2 and RV3
    Assembly Instructions

  5. Diode: D1
    Assembly Instructions

  6. Bc547: T1
    Bc557: T2
    Assembly Instructions

  7. capacitor 471: C1
    Assembly Instructions

  8. capacitor 473: C6
    Assembly Instructions

  9. capacitor 105: C11
    Assembly Instructions

  10. Follow these steps:
    A. Bend the pins of the 3mm white LED as shown in the pictures below.
    Assembly Instructions
    Assembly Instructions
    B. Cut a 7mm piece of 2.4mm shrink tube.
    Assembly Instructions
    C. Slide both the 3 mm white LED and the 3 mm photo transistor in the shrink tube as shown below. No need to actually shrink the tube. This will act as the lightbridge.
    Assembly Instructions
    D. Place and solder this assembly in LD2 and P1. Note the orientation of both cathode pins!
    Assembly Instructions

  11. Dc jack: J1
    Assembly Instructions

  12. capacitor 10µF: C14
    Note the polarity!
    Assembly Instructions

  13. 2 x Audio jack: SK1 and SK2
    Assembly Instructions

  14. 5 mm blue LED: LD1 (do a diode test with a multimeter to find the blue LED)
    Note the polarity!
    Make sure it stands out about 12 mm from the PcB, as shown in the picture!
    Assembly Instructions
    Assembly Instructions

  15. 5 mm white LED: LD3 (do a diode test with a multimeter to find the white LED)
    Note the polarity!
    Make sure it stands out about 12 mm from the PcB, as shown in the picture!
    Assembly Instructions
    Turn the PcB around!

  16. capacitor 220 µF: C2
    Note the polarity!
    Solder on the bottom side of the PcB!
    Assembly Instructions

  17. capacitor 10 µF: C5, C7, C8, C12
    Note the polarity!
    Solder on the bottom side of the PcB!
    Assembly Instructions

  18. capacitor 47 µF: C10
    Note the polarity!
    Solder on the bottom side of the PcB!
    Assembly Instructions

  19. capacitor 100 µF: C13
    Note the polarity!
    Solder on the bottom side of the PcB!
    Assembly Instructions

  20. Trim the leads on the 9 V snapt to 5 cm.
    Assembly Instructions
    Strip and tin both wires
    Assembly Instructions

  21. Place and solder the 9 V snap to the PCB as shown in the images below.
    Note the polarity! RED = +, BLAcK = –
    Assembly Instructions
    Assembly Instructions
    Assembly Instructions
    Assembly Instructions
    Slide 4,5 cm of the biggest shrink tube over the connector. When no battery is used in the pedal this cover should always be used.
    Assembly Instructions
    Assembly Instructions

  22. Place the finished board into the pedal casing and tighten it down with the supplied screws.
    Assembly Instructions
    Assembly Instructions

  23. Shorten all the pins on the footswitch by 1.5 – 2 mm.
    Assembly Instructions

  24. Install the footswitch as shown in the images below.
    Assembly Instructions
    Assembly Instructions
    Assembly Instructions

  25. Install the selector switch as shown in the images below

Assembly Instructions
Assembly Instructions

  1. Install the 2 potentiometers as shown in the images below. Note the placement of the different values!
    Assembly Instructions
    Assembly Instructions

  2. Trim the leads of the 6 wire female connector to 4.5 cm.
    Assembly Instructions

  3. Strip and tin the wires
    Assembly Instructions

  4. Cut 6 x 7 mm pieces of the 2.4 mm shrink tube.
    Assembly Instructions

  5. Solder the wires to the footswitch as shown below. Do not forget the shrink tube pieces and note the colors.Assembly Instructions
    Assembly Instructions
    Assembly Instructions

  6. Trim the leads of the 2 wire female connector to 4.5 cm.
    Assembly Instructions

  7. Strip and tin the wires.
    Assembly Instructions

  8. Cut 2 x 7 mm pieces of the 2.4 mm shrink tube.
    Assembly Instructions

  9. Solder the wires to the footswitch as shown below. Do not forget the shrink tube pieces and note the colors.
    Assembly Instructions

  10. Trim the leads of one of the 3 wire female connector to 4.5 cm.
    Assembly Instructions

  11. Strip and tin the wires.
    Assembly Instructions

  12. Cut 3 x 7 mm pieces of the 2.4 mm shrink tube.
    Assembly Instructions

  13. Solder the wires to the selector switch as shown below. Do not forget the shrink tube pieces and note the colors.
    Assembly Instructions
    Assembly Instructions

  14. Trim the leads of two of the 3 wire female connector to 5 cm.
    Assembly Instructions

  15. Strip and tin the wires of both connectors.
    Assembly Instructions

  16. Cut 6 x 7 mm pieces of the 2.4 mm shrink tube.
    Assembly Instructions

  17. Solder the wires to the 500K and the B10K potentiometer as shown below. Do not forget the shrink tube pieces and note the colors.
    Assembly Instructions

  18. Trim the leads of one of the 3 wire female connector to 7 cm.
    Assembly Instructions

  19. Strip and tin the wires of the connector
    Assembly Instructions

  20. Cut 3 x 7 mm pieces of the 2.4 mm shrink tube.
    Assembly Instructions

  21. Solder the wires to the B100K potentiometer as shown below. Do not forget the shrink tube pieces and note the colors.
    Assembly Instructions

  22. Slide the 3 knobs on top of the potentiometers.
    Assembly Instructions

  23. Plug all the connectors onto their correct plug and close the enclosure.
    Assembly Instructions
    Assembly Instructions

Plug in your gear and play!

CUSTOMERS SUPPORT

Velleman Projects

@Velleman_RnD

VELLEMAN nv – Legen Heirweg 33, Gavere (Belgium)
vellemanprojects.com

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals