PROSCEND 850G-6I Industrial Ethernet Switch Installation Guide

: June 12, 2024
: PROSCEND

Table of Contents

PROSCEND 850G-6I Industrial Ethernet Switch
Product Information
Reset Button:

PROSCEND 850G-6I Industrial Ethernet Switch

Product Information

Product Name: 850G-6I Industrial Ethernet Switch
Version: 1.00

Connecting Power:

The 850G-6I Industrial Ethernet Switch can be powered from two power supplies (input range 20~60VDC). Two power supplies are on the top panel of the switch. Insert the positive and negative wires (AWG 12-24) into V+ and V- contacts on the terminal block respectively and use a flat-head screwdriver to push in and open the wire clamp.

Second Power Supply:
WARNING: The DC power should be connected to a well-fused power supply.

Alarm Relay and Ground:

The alarm relay output contacts are shown as ALM next to the DC terminal block connector. The alarm relay out is Normal Open and it will be closed when it detects any predefined failure such as power failures. The relay output has a current carrying capacity of 1A @ 24 VDC. The switch must be properly grounded for optimum system performance.

LED Indicators:

LED	Description
PWR/RPS	PWR/RPS is powered.
ALM	Alarm for abnormal power status or function.
RJ45 LAN port Link/Act	Ethernet LINK UP.
RJ45 LAN port Speed	Ethernet LINK UP at 1000Mbps.

RJ45 Connector Pinouts:

Pin	Description
1,2	T/Rx+, T/Rx-
3,6	T/Rx+, T/Rx-
4,5	T/Rx+, T/Rx-
7,8	T/Rx+, T/Rx-

DIN-rail Mounting:

STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side of the switch.
STEP 2: Hook the unit onto the DIN-rail.
STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in place.

DIP Switch Setting:

DIP	Function	Description
1 (PWR)	ON/OFF	Primary power alarm reporting is enabled/disabled.
2 (RPS)	ON/OFF	Redundant power alarm reporting is enabled/disabled.

Reset Button:

Function	Operation
Reboot	Press the Reset button for 2 seconds and release.
Reset to factory default	Press the Reset button for 10 seconds and release.

Web Interface: Connect & Login

Factory default IP: 192.0.2.1
Login with default account and password:
Username: root
Password: 2wsx#EDC

NOTE: Please scan the QR Code below to download online resources.

Connecting Power

The 850G-6I Industrial Ethernet Switch can be powered from two power supplies (input range 20~60VDC). Two power supplies are on the top panel of the switch. Insert the positive and negative wires (AWG 12-24) into V+ and V- contacts on the terminal block respectively and use a flat-head screwdriver to push in and open the wire clamp

WARNING

The DC power should be connected to a well-fused power supply.

Alarm Relay and Ground

The alarm relay output contacts are shown as ALM next to the DC terminal block connector as the figure below.
The alarm relay out is “Normal Open”, and it will be closed when it is detecting any predefined failure such as power failures.
The relay output with current carrying capacity of 1A @ 24 VDC.
The switch must be properly grounded for optimum system performance

$PROSCEND-850G-6I-Industrial-Ethernet-Switch-FIG- $2$$

DIP Switch Setting

Reset Button

LED Indicators

RJ45 Connector Pinouts

The pin assignment of RJ45 connector is shown in the following table.

DIN-rail Mounting

STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side of the switch.
STEP 2: Hook the unit onto the DIN-rail.
STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in place.

Factory default IP: 192.0.2.1
Login with default account and password Username: root
Password: 2wsx#EDC

NOTE

Please scan below QR Code to download online resources. Download Link:
https://www.proscend.com/en/product/850G-6I.html

Proscend Communications Inc. All rights reserved.
www.proscend.com