eufy E83121D1 SpaceView Pro Baby Monitor User Manual

USER MANUAL
SpaceView Pro Baby Monitor

WHAT’S IN THE BOX

FEATURE INTRODUCTION

Monitor Features

1 Screen
2 Menu button
3 Navigation button
4 OK button
• Press to confirm the selection
• Press to switch camera display if you have added more than 1 camera
5 Return to the previous level of menu / Talk button
• Press and hold to speak to the camera
• When the menu is opened, press to return to the previous level of the menu| 6 LED indicator
• Red: charging
• White: Fully charged
7 Micro USB charging port
8 Volume down
9 Volume up
10 Power button
11 Zoom button
12 Reset
13 Speaker
---|---

Note: Power adapter varies by region.

Camera Features

SETTING UP THE CAMERA AND MONITOR

Charge the Monitor
Fully charge the monitor before use. To charge:

1. Connect one end of the micro USB cable to the baby monitor and the other end to the power adapter (5V/2A).
2. Plug the adapter into a power outlet.
3. Press and hold the power button for 2 seconds to turn the baby monitor on.

Charge the Camera

1. Connect one end of the micro USB cable to the baby camera and the other end to the power adapter (5V 1A).
2. Plug the power adapter into a power outlet.

The new baby monitor and camera will set up automatically. You are all set to use the products after the monitor and camera are fully charged.

ADDING A NEW BABY CAMERA

The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the following steps when adding extra baby cameras or after resetting a baby camera.

1. Enter menu settings, go to Camera -> Add Camera, then follow the onscreen instructions to start the pairing.
   

2. Press and hold the pairing button on the rear of the camera for 1 second until a notification prompt is heard.

3. Check the firmware version of the monitor (see image below) to make sure your baby monitor and camera are running the same, latest firmware version.
   

To check whether it is the latest version:

1. Visit the website below: https://www.eufylife.com/support/5505/spaceview-baby-monitor
2. Go to the “Firmware Updates” section and check whether your firmware version is the latest version. If not, download the “T8300 SpaceView xxx ‘’Firmware under the  “Firmware Updates” category. Make sure you download the version in the corresponding language.
3. Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware Upgrade Manual to complete the firmware upgrade.

Note:

• The baby camera can be added to the monitor. Before adding the camera, make sure the baby camera is running the same, latest version with the monitor.
• Chrome OS is not supported for firmware upgrades.
• Before you upgrade firmware, use the provided micro USB cable (1m) to connect the device needed to your computer.

USING THE BABY MONITOR

When two or more cameras are added to the monitor, you can manually switch among cameras by pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected baby cameras according to the preset intervals.
Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is resolved once the camera is moved away from the monitor.

PLACING THE CAMERA (WALL & CORNER MOUNT)

1. Use the monitor to test the viewing angle from your desired mounting spot.

2. Mark the screw holes with a pencil.

3. Drill 1/5” holes into the wall and then insert the anchors into the holes.

4. Insert the screws through the mounting holes of the wall mount and screw into the anchors.
   

5. Place the camera on the wall mount.
   
   You can select the way you like to install the camera.

MONITOR MENU SETTINGS

Press and hold the power button to power on the monitor. Press the menu button to open Menu Settings.

Menu Settings

min or Off.
Sound Alert| You can set the baby monitor to alert you when a specific noise level is detected.
Note: Surrounding noise might set off a false alarm.
Lullaby| Select your desired lullaby song. You can adjust the volume by selecting the volume button.
Note: Sound Alert is automatically disabled when the Lullaby function is enabled.
Warning: Your baby’s cry might be obscured by the sound of a lullaby.
Zoom| Zoom in / out
Alarm| • Set alarm on / off
• Specify the duration when the alarm will sound.
• Set the volume
• Set the temperature alert when it exceeds the specified temperature
• Set an alarm clock
Camera| Add Camera
Note: You can add up to 4 cameras per baby monitor.
Delete Camera
Cycle Cameras
Cycles through the list of connected baby cameras according to the preset intervals.
Time Set| Set the time on the monitor.
Night Vision Mode| When Auto is enabled, the camera will change the screen color according to the light conditions in the room.  When disabled, the camera will stick to daylight screen color and will not change when the surrounding environment is getting dark.
Note: We recommend setting this function to On for most of the situations.
Anti-Screen Flicker| Changes the refresh rate of the screen to prevent flickering.
Language| Sets the on-screen display menu language.
Default Settings| Resets all options to their default setting.
Temperature Unit| Select your desired temperature measure unit.
Connect with Us| Contact details

Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts during this interval, even if the conditions are met to trigger an alert.

On-screen Menu Icons

Note: This icon will not appear on the screen when there is only one camera connected to the monitor.
| Cycle Cameras enabled
| Sound Alert enabled
| The sound level of the room the camera is in
| Current time
| The current battery level of the baby monitor
| Current operating temperature

NOTICE

Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 1m (3ft) away). Never use extension cords with AC  Adapters. Only use the AC Adapters provided.

This product complies with the radio interference requirements of the European Community.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: www.eufylife.com
This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so-called power USB is prohibited.
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is 0°C-40°C
The suitable temperature for T8301-C and accessories is 0°C-40°C
When charging, please place the device in an environment that has a normal room temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from 5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using an unauthorized charger may cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8301-C) and 5Vdc / 2A (for T8321-M).The plug is considered as a disconnect device of the adapter.
If you use a third-party charger, the recommended output voltage/current of the adapter is 5Vdc / 1A (for T8301-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE  INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use products that maintain a 20cm distance between the device and the human body.
Operating Frequency Range: 2410-2477MHz The T8301-C Max Output Power: 18.04 dBm(EIRP), The T8321-M Max Output Power: 19.56 dBm(EIRP)
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321- M has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the limb is 0.310 W/kg. This device was tested for typical handheld operations with the back of the device kept 0mm from the Limb.
The T8301-Service has been evaluated to meet general RF exposure requirements and can be used in fixed exposure conditions. RF exposure information: The Maximum  Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use products that maintain a 20cm distance between the device and human body. )
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3-5, 80807 Munich,Germany
Anker Technology (UK) Ltd I Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom

****This product is designed and manufactured with high-quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on the disposal and recycling of this product, contact your local municipality,  disposal service, or the shop where you bought this product.

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3)
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.

FCC Radio Frequency Exposure Statement
The T8301-C device has been evaluated to meet general RF exposure requirements. The T8301-C can be used in fixed exposure conditions. The min separation distance is 20cm.
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm from the body.
RF Exposure Information (SAR)
The Extremity SAR limit of FCC for Handheld is 4.0W/kg.
The device is recommended to use in handheld only and SAR, when handheld, is 1.796 W/kg Worn on body will have unexpected RF exposure RISK.
FCC ID(for T8301-C):2AOKB-T8300C
FCC ID (for T8321-M): 2AOKB-T8321M
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: 1-800-988-7973

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>