BRESSER 88114004D7000 Walkie-Talkies Instruction Manual

: June 12, 2024
: BRESSER

Table of Contents

88114004D7000 Walkie-Talkies
General Warning
NOTES on Cleaning
Warranty & Service
EC Declaration of Conformity
Technical specifications
Introduction
Before using the device
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Walkie Talkies
Art. No. 8811400 WXH 000
8811400 4D7 000

Operating Instructions

88114004D7000 Walkie-Talkies

Belt clip removal

For charging via USB-C cable you need 3x AAA (per unit) NiMH rechargeable batteries.

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

MANUAL DOWNLOAD:

www.bresser.de/P8811400000000

General Warning

Risk of electric shock — This device contains electronic components. Only use the device as described in the manual, otherwise you run the risk of an electric shock.
Choking hazard — Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Leaking battery acid can lead to chemical burns. Ensure battery acid does not come into contact with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with plenty of water and seek medical attention.
Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire, or an explosion.
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Use only the recommended batteries. Do not mix old and new batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands, types or with different capacities. Remove the batteries from the unit if it is not to be used for a long period of time, or if the batteries are empty!
Never recharge normal, non-rechargeable batteries. This could lead to explosion during the charging process.
Rechargeable batteries are only to be charged under adult supervision.
The terminals must not be short-circuited.
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Keep instructions and packaging as they contain important information.

NOTES on Cleaning

Separate the device from the power supply or remove the batteries before cleaning.
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture.

Warranty & Service

The regular guarantee period is 5 years and begins on the day of purchase.
You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms.

EC Declaration of Conformity

Hereby, Bresser GmbH declares that the equipment type with part number: 8811400WXH000 (blue), 88114004D7000 (green) is in compliance with Directive: 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/8811400000000/CE/8811400000000_CE.pdf

UKCA Declaration of Conformity Bresser GmbH has issued a ,,Declaration of Conformity” in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration of conformity is available at the following internet
address: www.bresser.de/download/8811400000000/UKCA/8811400000000_UKCA.pdf
Bresser UK Ltd. · Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

Technical specifications

Frequency:	446.00625–446.09375 MHz
Channel number:	8 channels
Sub-code:	CTCSS 38
Transmission Power:	≤0.5W
Range:	Up to 6 Km in open field
Battery type:	3x AAA Alkaline (NiMH) rechargeable batteries
Device power input connection:	USB-C
Input voltage:	5,0 VDC
Input current:	0,15 A

Introduction

This set includes 2 Walkie-Talkie units: These are communication devices which operate on mobile radio frequencies. They come with 8 channels as well as a backlit LCD screen, enabling you to communicate over several kilometers free- of-charge (up to 6KM in open areas).

Key Functions

BRESSER 88114004D7000 Walkie Talkies - Introduction 1

1. Antenna
2. Light (Flashlight)
3. Display
4. Microphone
5. Power on/off button/Menu button
6. Light on/off button
7. Push-to-Talk button (Call/PTT button)| 8. Monitor & DOWN button
9. Scan & UP button
10. Speaker
11. USB-C connector
12. Portable clip
13. Battery compartment
14. USB-C charging cable
---|---

Before using the device

Remove the belt clip
Before inserting batteries into the device, first pull the belt clip latch away from the device.

Installing the Batteries

Open the battery compartment at the bottom of the battery compartment cover.
Insert 3x AAA alkaline NiMH rechargeable batteries (not included) into each unit.
Normal AAA batteries can also be used, but only NiMH rechargeable batteries can be recharged with the included USB charging cable.
WARNING: Never charge normal, non-rechargeable batteries! They may explode as a result of charging.
Position the batteries according to the polarity marking on the battery compartment.
After placing batteries into correct positions, replace the battery cover and attach the clip.

Charging via USB-C charging cable
The USB-C connector (1) allows you to charge NiMH rechargeable batteries by connecting them to a PC or other USB port.

Using the device

Turning the device on/off
To turn the device on or off, press and hold the Power button /MENU for 3 seconds until you hear a beep sound.
Adjusting the volume
To increase the volume, press the UP ▲ button. Press the DOWN ▼ button to decrease the volume.
Low Battery Indication
The device can detect the low battery level when the battery voltage goes low. When battery voltage is low, the battery icon will flash and a beep will be heard to indicate that the batteries need to be replaced.
Receiving/transmitting communications:
The device is in „Receiving“ mode when it is turned ON and not transmitting. When a signal is received on the current channel, the LCD will display it. When you hold the Call/PTT (push to talk) button, the device switches to “Transmission” mode. Hold the device in a vertical position with the Mic (microphone) 3-5cm away from your mouth. While holding the Call/PTT button, speak into the microphone in a normal tone of voice. Release the Call/PTT button when you have finished transmitting. For others to receive your transmission, they must be on the same channel as you.
Note:
1. The talking range will depend on your surroundings and environment. It will be affected by obstructions such as hills or buildings.
2. Don’t try to use two devices which are less than 1.5m (5 feet) apart. Otherwise, you may experience interference.
Changing Channels
Press the MENU button once, the channel number will flash on the display.
Press the up/down ▲▼ button to change the channel.
Press the Call/PTT button to confirm and return to stand-by mode.
Note: if no button is pressed within 15 seconds during setting, the device will return to stand-by mode.
CTCSS (Continuous Tone Coded Squelch System)
Press the MENU button twice, the current CTCSS code will flash on the display.
Press the up/down ▲▼ button to change the 38 available codes.
Press the Call/PTT button to confirm and return to stand-by mode.
As a license-free radio operating on the 400-470MHZ frequency band, the device has 8 available radio channels. If there are many device users near you, there is a chance that some of the users may be operating on the same radio channel. When using CTCSS, a low frequency tone (between 67250Hz) will be transmitted along with the voice signal.
There are 38 available tones to choose form. You are free to choose one of the 38 available sub-channels. Due to filtering, these sub-channels will generally not be audible so they will note disturb the communication. “OF” in the display means: OFF.
VOX (Hands free function)
The abbreviation VOX stands for “Voice Operated Exchange“. A walkie talkie with the VOX mode switched on is sound-activated, that means the transmission only switches on when a certain noise level is reached. You can set the voice activation level yourself. Press the MENU button three times, the current VOX setting will flash on the display and the VOX icon will display, Press UP ▲ button to set the VOX sensitivity level between 1 and 3 level (level 3 is the high sensitive level). Press down ▼ button until “OFF” appears on the display to turn VOX OFF. Press the Call/PTT button to confirm and return to stand-by mode. In VOX mode, the radio will transmit a signal when it is activated by your voice or other sound around you. VOX Operation is not recommended if you plan to use your device in a noisy or windy environment.
Note: VOX mode will be overridden when you press the Call/PTT button.
Scanning for an active radio channel
Press and hold the UP ▲ button 2 seconds: The “SCAN” function indicator will appear on the display and the channel will scan continuously from 1 to 8. Once an active channel is found, the scanning will stop and you can listen to the transmission. When the transmission on the found channel stops, the canning will resume automatically. Note: If you press Call/PTT button while listening to a found channel, the device will go back to stand-by mode on the found channel.
Monitor
Press and hold the DOWN ▼ button about 3 seconds to activate monitor.
Release the DOWN ▼ button to return to stand by mode.
Setting the Call tones
The device has 10 call tones.
Press the MENU button 4 times, “CA” is displayed and on the current call tone.
Press the UP/ DOWN ▲▼ button to change another call tones.
Press the Call/PTT button to confirm and return to stand-by mode.
Sending a call tone
Press the Call/PTT button once quickly, the call tone will be transmitted on the selected channel.
Roger Beep On/Off
After the Call/PTT button is released, the device will send out a roger beep to confirm that talking stopped.
Press the MENU button 6 times, “RO” will be displayed. Press the UP / DOWN ▲▼ button to toggle the roger beep ON/OFF. Press The Call/PTT button to confirm your selection and return to the stand-by mode.
Backlit display
Press any button except for the MENU button to activate the back light of the LCD display. The back light will illuminate for about 5 seconds.
Battery saving function
When the device has not been used for 6 seconds, the economy mode is automatically activated.
This does not affect the reception of transmission and the stand by mode is automatically re-activated as soon as a signal is detected.
Built-in Flashlight
Your device has a built-in light that can be used in sending light signals (e.g. morse code) or for your lighting needs (e.g. Flashlight). Simply press and hold the button.
Channel and Frequency (MHz)
Channel| Frequency
---|---
1| 446.00625
2| 446.01875
3| 446.03125
4| 446.04375
5| 446.05625
6| 446.06875
7| 446.08125
8| 446.09375

Disposal
Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
**** In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly for- bidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal in domestic waste violates the Battery Directive.
Batteries that contain toxins are marked with a sign and a chemical symbol.

battery contains cadmium
battery contains mercury
battery contains lead

Contact

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way, Edenbridge,
Kent TN8 6HF, Great Britain

@BresserEurope
Errors and technical changes reserved.
Manual_8811400000000_Walkie-Talkies_de-en-fr-es-it-pl-ru_BRESSER-JR_v032023a