XINJISMART S1 Shark 1 Speaker Instruction Manual

XINJISMART S1 Shark 1 Speaker Instruction Manual

packing list

Specifications

Please read the instructions before use

• Please note that speaker battery life varies with the volume of music being played. If at a lower volume, the battery life will be longer than if the speakers are playing at full volume
• If the speakers need cleaning, be sure to do so carefully. And make sure it is turned off and disconnected from all wireless devices. Do not use alcohol, benzene or other chemicals to clean the speakers and do not allow the speakers to be exposed to extreme heat or cold.
• Try to ensure that no physical damage comes to the speaker by falling, or coming into contact with hard surfaces or sharp edges.
• Do not disassemble the speaker or handle the battery in any way. If a problem occurs with the speaker, please contact the manufacturer for assistance. The battery must not be mishandled or replaced, as this may result in explosions or fire hazards. Therefore, please ensure that any servicing of the speaker is done by the service provider or manufacturer.
• If the speaker gets wet, please ensure that it is quickly and completely dried after coming into contact with water. Please do not allow the speaker to be submerged in water at all costs.
• Please keep the speaker away from the heat source, such as radiators, hot air regulators, ovens or other heat generating instruments, as it is not anti-high temperature.
• To protect your hearing and extend the speaker’s life, it is not recommended to adjust the volume to the maximum for a long time.

Method of operation

| Power on Short press Power off
Hold for 3 seconds
---|---
| Volume up:
Short press
Change to next: Hold for 1 seconds
| Volume down. Short press
Return to last:
Hold for 1 seconds
| Play/Pause: Short press
Receive a call
Short press to receive incoming calls
Reject call
Hold for 1 second to reject incoming call
Hang up call
Short press to hang up another call
Voice assistant:
Hold for 2 seconds to reject
| Disconnect the currently connected device and enter pairing mode: Short press Clear the paired list: Hold 7 seconds
| Enable TWS mode Short press
Disable TWS mode: Short press

Bluetooth Connect

1. Turn on the speaker and its LED indicator will flash blue in color until pairing is complete.
2. Activate the Bluetooth function of the phone and search for “XINJI-S1” Once the speaker has been selected and paired by you, there will be a sound prompt indicating the pairing.

Attention:

• The speaker can automatically reconnect to the last paired device.
• The speaker will automatically turn off if there is no pairing for 10 minutes.

Disconnecting the speaker
To disconnect the wireless connection, briefly press the wireless button.

TWS Connect

1. Confirm that the two speakers S1 are connected powered on, and the Bluetooth of the two speakers is on
2. Press the TWS button on the two speakers at the same time At this time, the LED indicators of the two devices will quickly flash green at the same time; after the pairing is successful, the sound prompt confirms the same, and only one flashes blue light, and the other blue light off, the green lights of the two devices flash twice every 5 seconds.
3. The device with the flashing blue light is the main speaker, follow the wireless pairing procedure to connect the main speaker to your mobile/media device.

AUX mode
To switch to AUX mode, simply connect the speaker to your mobile phone via the supplied AUX cable. If you want to switch to wireless mode, please remove the AUX cable.

Charging time

• Connect one end of the supplied charging cable to the charging input and the other end to a wall adapter, USB USB, etc.
• When charging, the LED remains orange.
• When the speaker is fully charged, the LED will turn on

Attention:

• Low power status: is indicated by orange LED flashing every 15 seconds.

Troubleshooting

A:

• Issue: The device cannot find “XINJI-Sl” on Bluetooth.
• Reason: The speaker cannot be in pairing mode.
• Solution: Restart the speaker to search again.

B:

• Issue: The speaker takes a long time to load.
• Reason: The power output of the adapter is too low, and the consumption of the charging cable is too high.
• Solution: Please choose the adapter with an output that is not less than DC 5V / 2A and use the original charging cable.

guarantee counterparty

www.xinjismart.com© 2022 XINJI Smart. All rights reserved.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that disturbances will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

• Reorient or lose the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.
• See the dealer or an experienced radio/TV technician for assistance.

This device and its antenna(s) must not be co-located or operating in conjunction with another antenna or transmitter.
Radiation Exposure Statement
The device has been rated to meet the general RF exposure requirement in a portable exposure condition without restriction.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>