robustel DMVPN App User Guide

App User Guide
DMVPN
Version: 1.0.1
Date: 2018-06-29
Status: Confidential

Revision History

Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions.

Overview

DMVPN (Dynamic Multipoint VPN) is a kind of dynamic establishes VPN Tunnel technology. DMVPN uses the NHRP (Next Hop Resolution Protocol) technology to analyze the end address of VPN Tunnel in the Hub-And- Spoke under the network environment; and uses the Multipoint GRE Tunnel port to establish Multipoint GRE over IPSec VPN Tunnel. DMVPN is based on IPSec VPN and GRE VPN.
DMVPN is an App which needs to install into router in System->App Center unit.

App Installation

2.1 Installation
Path：System- >App

1. Please place DMVPN App .rpk file (e.g. r2000-dmvpn-2.0.0.rpk) into a free disk of PC. And then log in router configuration page, go to System->App as the following screenshot show.
2. Click “Choose File” button, select DMVPN App .rpk file from the PC, then click “Install” button of router configuration page.
3. When the rate of installation progress reach 100%, the system will pop up a reboot router reminder window. Please click “OK” to make router reboot.
4. After router power on again, log in configuration page, DMVPN will be include in App Center’s “Installed Apps” list, and the function configuration will display in VPN part.

2.2 Uninstallation
Path：System->App Center

1. Go to “Installed Apps”, find DMVPN App and then click “ ”.
2. Click “OK” in the router reboot reminder pop up window. When router finish restart, DMVPN had been uninstalled.

Parameters Description

DMVPN

Item| Description| Default
Enable DMVPN| Click to enable DMVPN function.| OFF
Hub Address| DMVPN Hub’s IP address or domain| Null
GRE Local IP address| GRE Local tunnel IP address| Null
GRE HUB IP address| GRE Hub tunnel IP address| Null
GRE Netmask| GRE tunnel Netmask| Null
GRE Secrets| GRE tunnel secret key| Null
Negotiation Mode| Select from “Main” and “aggressive” for the IKE negotiation mode in phase 1. If the IP address of one end of an IPSec tunnel is obtained dynamically, the IKE negotiation mode must be aggressive. In this case, SAs can be established as long as the username and password are correct.| Main
Local IP Type| Select from “ID”, “FQDN” and “User FQDN” for IKE negotiation. “Default” stands for “Router’s extern IP”.
ID: Uses custom string as the ID in IKE negotiation.
FQDN: Uses an FQDN type as the ID in IKE negotiation. If this option is selected, type a name without any at sign (@) for the local security gateway, e.g., test.robustel.com.
User FQDN: Uses a user FQDN type as the ID in IKE negotiation. If this option is selected, type a name string with an sign “@” for the local security gateway, e.g., test@robustel.com.| default
---|---|---
IKE Encryption
Algorithm| Select from “DES”, “3DES” and “AES128” to be used in IKE negotiation. DES: Uses the DES algorithm in CBC mode and 56-bit key.
3DES: Uses the 3DES algorithm in CBC mode and 168-bit key. AES128: Uses the AES algorithm in CBC mode and 128-bit key.| 3DES
IKE Authen
Algorithm| Select from “MD5” and “SHA1″to be used in IKE negotiation.
MD5: Uses HMAC-SHA1.
SHA1: Uses HMAC-MD5.| MD5
IKE DH Group| Select from “MODP768_1”, “MODP1024_2” and “MODP1536_5″to be used in key negotiation phase 1.
MODP768_1: Uses the 768-bit Diffie-Hellman group. MODP1024_2: Uses the 1024-bit Diffie-Hellman group. MODP1536_5: Uses the 1536-bit Diffie-Hellman group.| MODP10242

PSK Secrets| Enter Pre-shared Key| Null
SA Encrypt
Algorithm| Select from “DES”, “3DES” and “AES128” to be used in IKE negotiation. DES: Uses the DES algorithm in CBC mode and 56-bit key.
3DES: Uses the 3DES algorithm in CBC mode and 168-bit key.
AE5128: Uses the AES algorithm in CBC mode and 128-bit key.
Note: Higher security means more complex implementation and lower speed. DES is enough to meet general requirements. Use 3DES when high confidentiality and security are required.| 3DES
SA Authentication
Algorithm| Select from “AH_MD596” and “AH SHA1_96” when you select “AH” in “Protocol”; Select from “MD5” and “SHA1″to be used in IKE negotiation. MD5: Uses HMAC-SHA1.
SHA1: Uses HMAC-MD5.| MD5
PFS Group| Select from “PFS_NULL”, “MODP768_1”, “MODP1024_2” and
“MODP1536_5”.
PFS NULL: Disable PFS Group
MODP768_1: Uses the 768-bit Diffie-Hellman group.
MODP1024_2: Uses the 1024-bit Diffie-Hellman group.
MODP15365: Uses the 1536-bit Diffie-Hellman group.| PES NULL
Nhrp Cisco secret| Cisco Nhrp secret key| Null
Nhrp holdtime| The hold time of Nhrp protocol| 60

Go to Status to check the DMVPN connection status.

Copyright© Guangzhou Robustel LTD
All Rights Reserved.

Documents / Resources

| robustel DMVPN App [pdf] User Guide
DMVPN App, DMVPN, App
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>