Xiaomi Redmi 12 5G Smart Phone User Guide
- June 1, 2024
- Xiaomi
Table of Contents
Xiaomi Redmi 12 5G Smart Phone
Specifications
- GSM / GPRS / EDGE / UMTS / LTE / 5G NR Digital Mobile Phone
- Bluetooth and Wi-Fi connectivity
- RF Exposure Information (SAR) compliant
- Frequency Bands: GSM 900, GSM 1800, WCDMA band 1/8, LTE band 1/3/7/8/20/28/38/40/41, 5G NR band n1/n3/n7/n8/n20/n28/n38/n40/n41, 5G NR band n77/n78
- Bluetooth: 20 dBm
- Wi-Fi: 2.4 GHz and 5 GHz bands
- NFC: 13.56 MHz
Product Usage Instructions
Safety Information
- Read all safety information provided in the manual before using the device.
RF Exposure Information
- Ensure the device is compliant with SAR limits for general population exposure.
Certification Information
- Check the SAR values for head and body exposure at a 5mm distance.
Frequency Bands and Power
- Understand the frequency bands supported in EU areas and their respective power levels.
FCC Regulations
- Comply with FCC regulations when using the device in the US.
FAQ:
What should I do if I exceed the SAR limits?
If you exceed the SAR limits, minimize your usage of the device or use it in a hands-free mode to reduce exposure.
Can I use the device in non-EU regions?
While the device supports specific frequency bands in EU regions, it may not be optimized for other regions. Check with your carrier for compatibility.
Declaration of Conformity
EU Regulations RED Declaration of Conformity
Xiaomi Communications Co., Ltd. hereby declares that this GSM / GPRS / EDGE / UMTS / LTE / 5G NR Digital Mobile Phone with Bluetooth and Wi-Fi 23076RA4BR complies with the essential requirements and other relevant provisions of the RE Directive2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.mi.com/en/certification
RF Exposure Information (SAR)
- This device complies with Specific Absorption Rate (SAR) limits for general population/uncontrolled exposure (Localized 10-gram SAR for head and trunk, limit: 2.0W/kg) specified in Council Recommendation 1999/519/EC, ICNIRP Guidelines, and
- RED (Directive 2014/53/EU).
- During SAR testing, this device was set to transmit at its highest certified power level in all tested frequency bands and placed in positions that simulate RF exposure during use against the head with no separation and near the body with a separation of 5 mm.
- SAR compliance for body operation is based on a separation distance of 5 mm between the unit and the human body. This device should be carried at least 5 mm away from the body to ensure the RF exposure level is compliant or lower than the reported level.
- When attaching the device near the body, a belt clip or holster should be used that does not contain metallic components and allows separation of at least 5 mm to be maintained between the device and the body. RF exposure compliance was not tested or certified with any accessory containing metal worn on the body, and use of such an accessory should be avoided.
Certification Information (Highest SAR)
- SAR 10 g limi t: 2.0 W/Kg,
- SAR Value: Head: 0.978 W/Kg, Body: 0.999 W/Kg (5 mm distance).
Frequency Bands and Power
- This mobile phone offers the following frequency bands in EU areas only and maximum radio-frequency power:
- GSM 900: 35.5 dBm
- GSM 1800: 32.5 dBm
- WCDMA band 1/8 : 25.7 dBm
- LTE band 1/3/7/8/20/28/38/40/41 : 25.7 dBm
- 5G NR band n1/n3/n7/n8/n20/n28/n38/n40/n41 : 26 dBm, 5G NR band n77/n78: 26 dBm Bluetooth: 20 dBm
- Wi-Fi 2.4 GHz band: 20 dBm
- Wi-Fi 5 GHz: 5150 to 5250MHz: 23 dBm, 5250 to 5350 MHz: 23 dBm, 5470 to 5725 MHz: 23 dBm, 5725 to 5850 MHz: 14 dBm
- NFC: 13.56 MHz < 42 dBuA/m at 10m
- 5G connection depends on country, carrier, and user environment.
FCC
FCC Regulations
This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
This mobile phone has been tested and found to comply with the limits for a
Class B digital device, under Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used under the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy. The exposure standard for wireless
devices employs a unit of measurement known as Specific Absorption Rate or SAR.
The SAR limit set by the FCC is 1.6 W/Kg. For body-worn operation, this device
has been tested and meets the FCC RF exposure guidelines for use with an
accessory that contains no metal and positions the device a minimum of 1.0 cm
from the body. RF exposure compliance with any body-worn accessory that
contains metal was not tested and certified, and use of such body-worn
accessory should be avoided. Any accessory used with this device for body-worn
operation must keep the device a minimum of 1.0 cm away from the body.
FCC Note
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Shielded cables must be used with this unit to ensure compliance with the
Class B FCC limits.
E-label
- This device has an electronic label for certification information.
- To access it, please go to Settings > About phone > Certification, or open Settings and type “Certification” into the search bar.
Instructions for Factory reset
- Path: Settings > About phone > Factory reset
- You can quickly erase the local data on the device via “Factory reset”. Data to be erased includes Accounts, Contacts, Photos and videos, Apps, Backups, SD card data, and Other items on this device.
Model: 23076RA4BR