SENECA T201DCH100-LP TRMS Direct and Alternate Current Transducer User Manual
- June 12, 2024
- SENECA
Table of Contents
T Series – Field converters
T201DCH100-LP – T201DCH300-LP
Contact-less direct and alternating TRMS current transducer
MI004500-E
General Specifications
- Direct and alternating current transducer galvanically insulated from the measuring circuit
- Measurement principle: Hall Effect
- Possibility to measure the direct and alternating component of TRMS current
- No shunt, no wasted power of primary current Circuit and no dissipation.
- Unipolar or bipolar measurement.
- High measurement accuracy: 0.5% ****1%.
- Suitable for Seneca modules with power supply sensors at 12V ****and input 4 – 20 mA.
- Two DIP-Switches selectable ranges.
- Damping filter availability to improve stable reading.
- Suitable for batteries, battery chargers, solar panels, power units and generic dc loads.
- Compact dimensions: 96,5 x 68 x 26 mm.
| 
---|---
http://www.seneca.it/prodotti/t201dch300-lp|
http://www.seneca.it/prodotti/t201dch100-lp
This document is property of SENECA Srl. Duplication and reproduction are
forbidden, if not authorized.
Contents of the present documentation refers to products and technologies
described in it.
All technical data contained in the document may be modified without prior
notice.
Content of this documentation is subject to periodical revision.
Technical features
INPUT
Measure type| AC / DC TRMS or Bipolar DC.
Range 7201DCH100- LP
Range 1201 DCH300-| 0— 50Aor 0 — 100A TRMS; -50 — +50A or -100 — +103A Bipolar
0 — 300Aor 0— 150A TRMS; -150— +150Aor -300 — +300A Bipolar (selectable by
dip-switch.).
Peak factor| 1.
Bandwidth| 1 kHz
Insulation| When a sheathed wire is used, the insulation voltage is set by
sheath properties. On a bare wire, it’s stated to 3 kV iv.
Over-current| 2000 A impulsive, 500 A permanent.
OUTPUT AND POWER SUPPLY
Type| 4 — 20 mA, max. load R,..=600 D. Screw terminals: 0 and 0.
Terminals| Screw terminal pitch 5.08mm for max 2.5 mm’ cables.
Hole diameter| 20.8 mm
Power supply| 9 — 28 V= (between 0 and 0)
Protections| – Polarity reversal – Over-Voltage
Fail indication| < 3.8 mA
Max. indication| < 22 mA
PRECISION
| Range| Precision N| Precision
Over the 2%
of End of Scale| 100 A or 300 A 50 A or 150 A| 0.5% of end scale.
1% of end scale.| 1% of end scale.
2% of end scale.
Under the 2% of End of Scale| 100 A or 300 A 50 A or 150 A| 1% of end scale.
2% of end scale.| 2% of end scale.
4% of end scale.
Resolution| Output: 10 bit (1000 points) Input: 12 bit (4000 points).
Temperature coefficient| < 200 ppm/°C.
Error due to EMI| <1%
Response time| – Fast filter 500 ms.
– Slow filter 1000 ms.
Measure hysteresis| 0.3% of the end scale (typical)
OVERVOLTAGE CATEGORY
Bare conductor| CAT. III 300V
Insulated conductor| CAT. III 600V
OPERATING CONDITION
| Protection degree | IP20. |
|---|---|
| Operating temperature | -20 – +70 °C. |
| Storage Temperature | -40 – +85 °C. |
| Humidity | 10 – 90 % non-condensing. |
| Altitude | Up to 2000 m a.s.l. |
CASE
| Weight | 47 g. |
|---|---|
| Overall dimensions | 96,5 x 68 x 26 mm (without terminals) |
| Box material | PA6, black color |
STANDARDS
| EN61326 (EMC requirements)
EN61010-1 (safety)
---|---
DIP-switches
| Range | Filter (10% — 90%) | Mode | Not Used |
|---|---|---|---|
| 1 | DCH100 | DCH300 | 2 |
| 0 — 100A | 0 — 300A | Filter = 800ms | |
| 0 — 50A | 0 — 150A | Filter = 2000ms |
In the table the symbol corresponds to the switch in the ON position.
The instrument is factory delivered with range:
100A (T201DCH100-LP) or 300A (T201DCH300-LP), 800ms filter and RMS
mode.
Mounting
The device can be located in any position and place, in accordance with the
operating conditions above stated. Use the included holder bracket when fixing
to a DIN rail.
WARNING: High-strength magnetic fields may change the measured output value:
Let avoid closeness to permanent magnets, electromagnets or iron bulks that
cause such a modification of the surrounding magnetic field; try a different
arrangement or
orientation if zero error was greater than expected.
Multi-turn primary winding to improve sensibility
You can increase the sensibility of the device simply passing several times in
the hole with the measuring current, realizing turns with multiplicative
effect:
For example, passing 5 times in the hole, as to see 4 turns, choosing a 50 A
range, you get an equivalent sensibility of 10 A full-scale. When you make
this, let dispose the turns with symmetry in order to preserve accuracy: use
diametric contraposition with 2
turns, cross disposition with 4 turns, with 6 turns at 60° and so on.
Disposal of electrical & electronic equipment (applicable throughout the EU
and other countries with separate collection programs). This symbol, found on
your product or on its packaging,
indicates that this product should not be treated as household waste when you
wish to dispose of it.Instead,it should be handed over to an applicable
collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent
potential negative consequences to the environment and human health, which
could otherwise be caused by inappropriate disposal of it. The recycling of
materials will help to conserve natural resources. For more detailed
information about the recycling of this product, please contact your local
city office, waste disposal service or the retail store where you purchased
this product.
www.logicbus.com
sales@logicbus.com
+1 619 616 7350 SENECA s.r.l.
Via Austria, 26 – 35127 – PADOVA – ITALY
Tel. +39.049.8705355 – 8705359 – Fax +39.049.8706287
Manuals and configuration software are available at
website:
www.seneca.it/products/t201dch100-lp
and
www.seneca.it/products/t201dch300-lp
Technical support: support@seneca.it
Product Informations: sales@seneca.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>