CleaninGuy SM1050 Walk Behind Sweeper User Manual

CleaninGuy SM1050 Walk Behind Sweeper

Security
The following symbols indicate potential hazardous conditions. It is particularly important to read the instructions with regard to necessary measures of precaution and protection.
The essence of the manual is to prevent the danger of accidents, and most of accidents are occurred during to carelessness about safety operation rules. The best guarantee of getting away from accidents is that the users are careful and cautious, which is better than other prevention. Be careful to your surrounding and people around, especially children, when using the sweeper.

Symbol instructions

General Instruction

1. Be sure to turn the power off and meanwhile take off the key from power switch before any maintenance.

2. Be sure to operate by professionals who are specialized trained when using the sweeping machine. It is strictly prohibited to operate by non-professional personnel.
   No drunken driving, don’t bring accessories and don’t wear long scarf, try to wear uniform to work.

3. Don’t use in such dangerous places which include explosive gas, liquid water and vapor.

4. Ensure the battery in a ventilated zone when charging. It shall promptly charge the battery when the machine stops working or appearing low voltage alarm during run-time, and at the same time, keeping the lid open, getting away from the fire, both of which would prolong the life of the battery and security.

5. the reason why it is strictly prohibited to cleaning the wire rope, belts, high temperature sundry, water, flammable or poisonous and harmful material is to avoid winding, burning the main brush and the side brush, to make it can’t work normally.

6. It is prohibited driving in more than a steep slope or high-speed road meanwhile be careful with sharp corners.

7. When the machine works, we should control the work speed less than 5km/h, and vibrate dust every 30-45 minutes so as to achieve the best of cleaning effect.

8. Turn off the power after using and then try to put it in the house, store or flat place.

Warning!

1. Please read the maintenance instructions before any maintenance and repair operations.
2. Please keep your loosen clothing, hair, fingers and any part of the body away from air inlet of machines and any moving parts.
3. Battery charger should get far away from high heat place.
4. Connecting the battery charger to the trunk circuit while ensuring the voltage and frequency consistent with parameters of charger nameplate signs.
5. Don’t charge the battery if battery charger cable is damaged or battery immersion, besides, damaged machine is also included.
6. The wire of battery charger shall not be used by pulling the machine and meanwhile don’t regard charger wire as the handle.
7. Don’t open voltage switch and start operation during battery charging period.
8. Please don’t be placed in the open air so as to avoid electric shocks.
9. Don’t treat the machine as a toy; especially pay attention to keep the children far away.
10. Remember to take off the key when the machine stops.
11. Don’t drive on the steep slope which is far from its limit.
12. If the thickness of roads waste is more than 2 millimeter, please adjust the running speed of the machine according to adhesion of the ground garbage, and then repeat cleaning operation.
13. Don’t put the cup or the bottle with other liquid water on the machine.
14. The operation duration shall not exceed 30 minutes when the temperature is 40 degrees or above. A t this time, the machine is not only vibrated dust and cleaned dirt, but also rest for 5-15 minutes and then for the next operation.
15. Never put the machine as a means of transport.
16. When the machine is not working, stop rolling the brush to avoid to wear brush, leading to affect the used life
17. Once fire, don’t put out the fire with water just use the power fire extinguisher.
18. Don’t bump the dangerous shell on which may drop down items.
19. Don’t change safety protection device of the machine. Execute according to the maintenance program.

Machine Structure Introduction

Technical Parameter

Battery safety requirement

1. The battery is not allowed to work in a low voltage state, charge the battery immediately once the low voltage alarms.
2. Free maintenance battery and no need of adding electrolyte.
3. To avoid leakage, please keep the battery dry; clean, especially to avoid erosion of pollutants like metal powder.
4. The metal part such as the tool is banned to place on the battery so as to prevent burning out the short-circuited battery.
5. When the battery is recycling please implement according to the local regulations.
6. The fire is prohibited to use when you hand or process the battery.
7. The charging room should be well ventilated.
8. When the sweeper is turned on, it is not allowed to connect or disassemble the battery.

Before Operation
Be careful!

1. Check whether the parts of machine are damaged during transit movement.
2. Close top cover, tighten the dustbin hook and make sure that the machine can work normally.

Start Operation

1. Driving mode
   A. Ensure that the side brushes and the main brushes are in raised position.
   B. Push the adjuster to decline side brushes.
   C. Turn on the power, the side brush will work automatically.
   D. Push the sweeper to the place you want to clean.

2. Cleaning mode
   A. When you turn on the power button, the side brushes will work automatically.
   B. When you turn of the power button, . the side brushes will stop working.
   C. If the working environment is relatively bad, stop sweeping after intervals meanwhile use red button to clean dust in filter.
   D. Check the garbage and empty the dustbin in time
   Notice : wire rope, belts and similar garbage is forbidden to sweep.

One-Button-Control Water Spray System for Dust Suppression

How to Use the Water Spray/ Wet Dust Suppression System?
Like a street sweeper, SM1050B Floor Sweeper equips with two 6501 flat fan water spray nozzles to help control dust with the fine water mist; it is useful in dusty conditions to suppress the dust and keep the air quality and the operator’s safety.
It’s very easy to operate: add water to the tank, start the machine, press the “Watering” switch on the control panel to activate the water spray, and press the switch again to turn it off.

NOTE : Do not use the water spray system on wet surfaces.

Q: Why there’s mud when using the water spray system?
A: The mud may be created due to heavy dust or wet surfaces. We suggest waiting until the surface is dry, then do the sweeping to get the perfect results. And make a regular maintenance plan to keep the dust from building up.

Stop Operation
1. Turn off the key button.

Empty the dustbin

1. Stop and clean filter.
2. unlock hook of dustbin.
3. Pull the dustbin downward, then drag out to empty.
4. Put the dustbin back inside the machine and fasten the locking buckle of dustbin.
5. Finish routine examination for the next work.
6. Push or drag machine

After operation
Please perform the operation before leaving the machine when finish working.

1. Use adjuster to raise the side brushes.
2. Use red button to clean dust in filter.
3. empty the dustbin
4. Turn off the power and take off the key.

If you don’t use the machine for a long time (at least 15 days)
Please do as follow:

1. Check and keep the machine dry
2. Disconnect the battery terminal, recharge at least one time per month

Repair and maintain machines

1. The machine maintenance shall be according to correct routine.
2. Perform strictly according to the maintenance schedule.
3. Perform maintenance operation after stopping the machine, (pulled out the key), remove battery when necessary, please read the instructions carefully about safe sections.

Maintenance schedule

Note : The interval time of the maintenance can be changed, but it has to be decided by the professional personnel who are responsible for maintenance.
Notice : Check the pressure of the main brushes on the ground
Check whether the brush is in the right position , the process is as follows:

1. Operate the machine on the flat road.
2. Keep the main brush stop and rotate for a few second.
3. Check the trace of the main brush, along which you need to see whether the length is 2-4 cm, if not, adjust the pressure between brushes and ground. The screw is used to adjust the height of main brushes from the ground.
4. Please replace when the brush is abrasion, must be adjusted.

Be careful! The normal operation of the machine will be affected if the trace of the brush is more than 5cm, and spare parts will be hot, therefore shorten service life of the machine.

Replace the main brush
Please wear gloves to prevent being scratched when replacing main brushes.

1. Park machine on flat ground
2. Stop sweeping function.
3. Turn off the key
4. Open left side door (Picture 9)
5. Screw off B
6. Screw off 1、2 nut。
7. Screw off 3、4、5、6 nut.
8. Pull out broom A.
9. Remove broom A.
10. Check if there is any rope inside
11. Install new main brush like picture 10.
12. Install round plate and nuts
13. Close left side door.
14. Check and adjust the height of main brush .

Notice: Check and adjust the height of side brushes

1. Check side brush height by follow procedure:
   A. Operate the machine on the flat road.
   B. Keep the machine stop and run side brush for a few second.
   C. Rise side brush, move the machine and then stop the machine
   D. Check the cleaning trace of side brush according to picture 11 (A and B).
   If the cleaning trace is not within normal limits, adjust the height.

2. Press brake pedal

3. Turn off key

4. Open left side door

5. Adjust bolt A to make B fall to suitable position (Picture 12)

6. Lock bolt B

7. Check brush side again

8. If the brush is abrasion, need to change.

Replace side brush
Please wear gloves to prevent being scratched when replacing side brushes.

1. Park machine on flat ground
2. Turn off key
3. Screw off nut A (Picture 13), and press brush to remove it
4. Change new one and tight nut A
5. Check and adjust side brush height.

Machine fault and troubleshooting

Connect wire again
When press accelerator pedal, the machine don’t move| Handbrake is working| Loosen handbrake

Travel switch broken

|

Change travel switch

Main brush don’t work| Contactor is not connected| Reset contactor
Side brush don’t work| Main brush doesn’t get down| Bring down main brush
Contactor is not connected| Reset contactor
The sweeper only sweep when it doesn’t move, or the battery indicator shows less than 4 red grid (Low power)| Battery no power| Charge battery .

If still have problem, suggest to change new battery

Low battery| Exceed battery life| Change battery
Battery broken| Repair or change battery
Note: Other problem please connect us for identify.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>